Thank you , I want one of these motor bikes ! I'm 62years have wanted a Trials bike for 40 years ! Live in Canada, British Columbia , great place for one of these Babies ! Thanks again for sharing the VID. Gerald Woodward
@OKFrax-ys2op10 ай бұрын
How many hours can be expected on the Honda engine before it’s rebuilt? Considering proper maintenance is done?
@Oldbrokenbones4 ай бұрын
Ever........ we had to do this, these bikes run for ever
@OKFrax-ys2op4 ай бұрын
@@OldbrokenbonesI just bought a 2018 Honda Monty with less than 200 miles on it, time to get cracking!
@pedrodaniz96642 жыл бұрын
Good old honda engines.... never fail
@ROBERTBUDA-RBMV6 жыл бұрын
Hello. How often do you have to replace the piston and rings in this engine? Greetings from Poland.
@Spoonersoutings6 жыл бұрын
One reason why I hate 4stroke engines, good job on the rebuild 👍 only smokers for me cheaper and easier to fix
@mike3004065 жыл бұрын
you got it I would buy 1 if I was loaded just for an extra bike for some 1 to ride etcetc I would take it out to of course but when I seen all the maintenance even the oil change`s its just as much or more than a 2 stroke which you would think shouldn't be
@keithsmith42362 жыл бұрын
@@mike300406 see I used to think that but all 2t bikes eventually required a complete rebuild due to wear.. mains and big end don't have the benefit of a lovely oil sump to keep em well lubed. I've done too many to count. Next bike is a mont see how I get on with it
@darrenfowler69907 жыл бұрын
Just drowned my 4rt! Did you replace the rod?If so what make and part no and where did you get it from? Thanks.
@r6eck7 жыл бұрын
We used Pro X conrod for a CRF250X supplied by Ecosse MX who sell on ebay.Honda don't supply a conrod separately ,its a complete crank from them.If you bend the rod then you will have buckled the piston skirt too.New piston required.All parts used were genuine Honda other than the rod.
@bobellisp59 ай бұрын
Alex noes his way around these bikes
@davidswatton748 жыл бұрын
good work Alex,
@canadapainter6587 жыл бұрын
(I looked it up) it is a low compression bike vs. others and that is why there is no high end speed. It only needs to make you move vs. take off on the slopes...
@juancarloredondo77516 жыл бұрын
hey stive i have honda montesa4rt260 i dont have tank . i want to change the look my plans is card look my problem is i dont have fuel pump of honda montesa and i dont have pgi box what is the similar parts to install for pgi box and fuel pump
@bikeracr7 жыл бұрын
how did it hydro lock-blown head gasket or drowned in a puddle,creek ect.?
@Oldbrokenbones7 жыл бұрын
Crossing a river, fine at the start but got deep at the other side : (
@badlarry1727 жыл бұрын
great film thanks
@mike3004068 жыл бұрын
never thought I would ses such a short stroke how does it run some 1 told me its like a vibration
@Oldbrokenbones7 жыл бұрын
No it's fine...... smooth with shit loads of torque
@gscranage45943 жыл бұрын
Or a short piston!
@edrtaylor7 жыл бұрын
How do you get on with the handlebar tank? Does the siphon work ok?
@r6eck7 жыл бұрын
Siphon works fine, im running a 3 litre acerbic tank ,Clark has my "spare" 1 litre tank.
@Oldbrokenbones7 жыл бұрын
Like a dream
@pepetemega95797 жыл бұрын
Buen trabajo :)
@beppeventura41217 жыл бұрын
what means Hydro Locked Engine ? thank's
@jvboy567 жыл бұрын
Hydro locked is when a engine has a liquid in the top end which will not compress resulting in the engine not being able to turn over and usually causes damage such as you see here (bent rod) a cracked cylinder ,head or gasket failure can cause this problem as well as the engine sucking in water through if the carb becomes submerged
@whalesong9994 жыл бұрын
@@jvboy56 But, how did these get hydro locked? Once had a riding partner in an enduro that sunk his OSSA Plonker in a stream and we had to turn it upside down once on the banks, remove the plug, and turn over and over til it was relieved enough. Was a bugger to restart but he went on to finish w/no rod damage.
@omdoyot30634 жыл бұрын
Buen honda ko uda
@Despertaferro1006 жыл бұрын
Nice!
@dexterthompson18096 жыл бұрын
valves sound loose.
@canadapainter6587 жыл бұрын
what is the top speed of those bikes?
@Oldbrokenbones7 жыл бұрын
On a good day 55mph...
@canadapainter6587 жыл бұрын
Steven = it is funny It got so slow top speed as 250cc. A 125cc regular 4Stroke bike can 110km/h top.
@Oldbrokenbones7 жыл бұрын
It's down to gearing and the purpose it was built for, I'd like to see anything else ride up a near vertical waterfall..........
@canadapainter6587 жыл бұрын
Steven = vertical clime is not bike power it is momentum. Power is there to get momentum.Also I wonder what gearing has to do with it... since a big sprocket in the back can fix torque issue.
@alanglen59025 жыл бұрын
What dreadful music!!!!!!
@mrpantur72806 жыл бұрын
Probs best not to rev a cold engine that's just been rebuilt.
@Oldbrokenbones6 жыл бұрын
Yep! we cheated and had it warmed up first : )
@mrpantur72806 жыл бұрын
Steven Clark oh aha ..
@Oldbrokenbones7 жыл бұрын
Rod from a CR250! call Micky Oats in Glasgow, tell him you need the same parts for a rebuild, same as the Dundee guy's, he's a fine guy, and will have the parts listed........ 0141 332 7374, we ended up changing the piston too, as there was a little slap we couldn't live with?
@fulviozilantra6436 жыл бұрын
Old trial
@gscranage45943 жыл бұрын
From 2004
@grahamwright84474 ай бұрын
Horrible music , turned off .
@alanyeo88293 жыл бұрын
moved on music sucks
@Oldbrokenbones3 жыл бұрын
turn the volume down .................. youtube changed it....... not my selection