More Interesting Things About Friction And Mechanical Heating - It's All So Interesting!

[@LatkaXtreme]

"Lots! Lots, and that's metric lots as well as imperial lots!" is going straight to my vocabulary

[@camifracelli631]

+1 for heat pump. You might even be able to connect the compressor directly on the 2nd shaft. Get everything you need from an old fridge: don't forget the safety valves. And good luck for your cold. :)

[@Tater1337]

most compressors are completely sealed, so it is still impractical, and most require a minuimum RPM, so you'll have additional losses in whatever gearing or other power conversion you use those losses will most likely be in heat, and be harder to harvest than the plan he has already

[@thoughtfox2409]

@@Tater1337 One could use an old Truck engine as a compressor, though. All you have to do is adjust the Valve timing so that they can in fact compress air, and with the high volume of those engines a low rpm should be feasible. And trashed engines (where the issue isn't the engine itself) are quite cheap

[@Tater1337]

@@thoughtfox2409 cheaper than a few metal plates? and trying to convert an engine for a compressor will NOT work well for a heat pump

[@Tater1337]

@@thoughtfox2409 simple answer to this, how many old truck engines do you see used for compressors? sounds good in theory, and has been used a few times in practice, but.......

[@thoughtfox2409]

@@Tater1337 You don't see that many old truck engines used as compressors because most high-volume low pressure compressors are industrially used. And a business would never buy the cheap redneck solution, but a brand new piece of equipment. Why? If a Business can write off either a few euros or a few thousand euros for tax purposes they will always choose the few thousand euros. Aditionally to that, screw or turbo-compressors are less maintenance heavy than piston-compressors, so they are cheaper to run long term. And very few private uses need the few thousand liters per minute an engine turned compressor could provide. As far as the unsuitability goes: Yes, usually you would want high pressure low volume, however, a diesel engine usually works at 14:1 to 25:1 compression rates. So if you were to change these around at least 8 bar should be possible. Thats roughly the same compression that most house heat-pumps work at. So you don't even need a truck engine for high volume, a car engine is probably enough, and those are dirt cheap if bought for scrap value.

[@TheNomadluap]

If you're worried about mechanical losses in the gearing, one way to mitigate that is to put the gears themselves in the fluid. Then the "waste" friction of the gears isn't waste at all!

[@everettrubel7112]

You could build an insulated workroom around or over the gearing at the bottom and get a heated workroom for free.

[@ooslum]

Hey Tim, may have been said but the favorite for energy storage is a sand battery. How about stirring the sand to heat it, like a huge rock tumbler, low speed high torque can be used by large diameter tumbler and small diameter for high speed low torque. The paddle could be made variable diameter or pick up more if available energy rises. Cheers

[@GradyHouger]

That's a great idea for my daydream of manufacturing sand.

[@peterlarson233]

If your metal plates gain weight from the friction, you can exchange them with somebody else whose plates lose weight from friction. Keep trading them back and forth and you'll solve each other's problems!

[@lordneador3724]

this guy trades!

[@sinisterhipp0]

Flawless

[@Manigo1743]

If his plates gain weight from friction, wouldn't everyone elses plates do the same?

[@rasmuslymo]

What about a watercooled aircompressor. Then you get compressed air for the workshop, and heating of the water.

[@totherarf]

Now That is a good idea!

[@ZwilnikSF]

Connect the air powered loco in reverse to the windmill and use its pistons to compress air for it. If you have a water jacket around the pistons and air tank they should also generate a fair bit of heat :)

[@SCronin944]

Tbh best idea in the coments yeat yeat

[@dennisolsson3119]

That is basically halft of a heat pump and an awesome idea!

[@rasmuslymo]

I want to build one now LOL

[@KrisHarbour]

Hi Tim, just an idea to get some more RPM if you look at my waterwheel build I used a shaft mounted 20-1 gearbox. they are called shaft mounted conveyor gearboxes. I have found that the one I used only get slightly warm when running at 16rpm with 2kw going through it. So I have 16rpm getting geared to 320rpm. then a 2.4-1 pulley belt drive that takes it up to 768rpm to run a 8pole induction motor. The loss in this setup is very low. nothing gets more than just warm to the touch. if you did a 5-1 pulley from the gearbox you could achieve some high rpm. 20 rpm x 20 = 400 rpm. then a 5-1 pulley =2000 rpm. there is losses but for 2kw the loss is in the region of 200-300w Also because a lot of the loss is happening in the gearbox itself and you are trying to make heat. that heat could be recovered from the gearbox as well. it would add complexity but is possible. The belt drive though would be to complicated to recover the heat so that would be lost But the closed gearbox unit could have a heat exchanger on it. I do like the induction heater idea. Neodymium magnets are so expensive and corrode. because size won't be much of an issue for you ferrite magnets could be much cheaper for the same magnetism and they have the benefit of not corroding much at all. these are big and reasonably priced www.first4magnets.com/rectangular-c35/152-4-x-101-4-x-25-4mm-thick-y30bh-ferrite-magnet-20kg-pull-p2549#ps_0_2570|ps_1_726 if you want any info on the gearboxes just send me and email mate. Great video.

[@wayoutwest-workshopstuff6299]

Thanks very much, Kris. I didn't know such things existed - I do now though!

[@MisterTalkingMachine]

Some old automotive AC systems used compressors that were powered directly by the engine belt via a pulley, I think such a thing could be a good candidate for running a heat pump if you can get your hands on one, I've also heard (though correct me if I'm wrong) that some hobbyists have built heat pumps / refrigeration systems using propane as a refrigerant.

[@arjovenzia]

As an electronics engineer, I would obviously default to a generator, but I really respect the mechanical approach. I honestly would have never of thought of it as an option. But I like it, alot. and the vibe im getting is your doing this for the fun of the project, not profit or anything like that. I think your on a pretty good path, you could do alot with 1kw of constant heat. Hope your feeling better soon Mate

[@paradiselost9946]

can you explain how to get a generator to deliver power on the same rate as wind power, the cube of the velocity? ie, double the RPM, produce FOUR times the output. then theres the whole issue about jacobs law and exactly where the power is appearing, in the generator? or in the load? so you get the generator to increase its output in proportion with the wind, but whats the point? wheres that power going? whats it doing? as per above, jacobs law... the generator is only half the issue. the load itself is the other half. to "increase the generators output" requires the load also change to allow for that... yknow, ohms law and all that, its not simply a matter of "increasing the generators output" as its dependent upon the load as well... and as we keep being told, wind doesnt deliver its power reliably, predictably. its erratic and fluctuates wildly. how to match that to the ideal load with a generator and maximise our yields when we have no idea what the power source is going to do next? batteries? that can only accept so much charge before wasting excess energy as heat? eventually degrade and need replacing? rely on mysterious black boxes that love to release magic smoke? as an uneducated highschool dropout, im doing my best to get as far away from electronics and generators as possible. magnets and conductors? great. far better than friction based ideas. electronics and generators? no thanks ;) heat is easily stored, easily produced, and whilst not overly convenient... is relatively easy to convert into electricity, as required, and thats relatively straightforward when you have a power source that behaves in a predictable manner. what do we mostly use electricity for anyway? to make heat.

[@optroncordian7863]

You do not need rotational speed, you actually need linear speed to make the hydrodynamic friction work. So, instead of increasing the RPM, you can increase the diameter of the rotating element, thus reducing the losses from gearing.

[@mrMacGoover]

5:35 "The plates seemed to have gained weight " 😅 those are some magical plates you got there!😂

[@timothymeyer3210]

or just wet plates

[@sivansharma5027]

@@timothymeyer3210 No, wet plates wouldn't gain that much weight. It's 100% definitely MAGIC!

[@Jettaheizer]

Thinking of friction - what about car or even truck (lorry) brakes? They´re made to turn kinetic energy into heat and release it into the air (or in your case water) around. You could stack brake discs and pads inside a pot and control the friction with a spring pressing on the whole stack. The more rpm the windmill turns, the more pressure on the spring so alongside to the heat you get kind of a governor for the rpm of the mill. My idea is four brake pads, then the disc and then again four pads. Then the same setup again and again. The discs are turned by the shaft while the pads are held by some kind of track so they can move a little up and down (as necessary depending on the wear and tear) but not sideways. I´ve got lots of ideas for this, but no possibility to test it myself.

[@Nelo390]

Just absolutely make sure they aren't asbestos based (they still exist in america), also you probably want a way to contain the dust because any of it is absolutely unhealthy :(

[@vladimus9749]

What about cutting up a second disc and using that as the "pads" or simply sandwiching the discs without pads? Brake pads are made to take most of the wear while providing a quiet smooth, fast braking experience which we don't care about. Discs are made to provide a friction surface and dump their heat into the surrounding area which is what we want. I guess it also depends on economics of what he could get the cheapest. So many experiments!

[@lafayettehighball106]

That is what I suggested on the last video. Glad someone else thought that too.

[@paradiselost9946]

pads waer out. brake rotors wear out. make dust. squeal. need maintenance. servicing. eddy currents, magnetic induction, does not.

[@CNCmachiningisfun]

I made an induction heating device, a few decades ago, that easily boiled water, when operating at 400 RPM. It had 16 magnets, arranged on the face of a 400mm steel disc. These faced an aluminium plate, with a clearance of about 4mm. When spun at a mere 400 rpm, the plate soon reached 200 degrees C, and turned water into steam :) . That's the way to do it, in my humble opinion.

[@wayoutwest-workshopstuff6299]

I'm intrigued - that sounds too small, but perhaps they were big magnets? Do you have a video of it?

[@CNCmachiningisfun]

@@wayoutwest-workshopstuff6299 Yeah, it was rather small, but that was all my antique lathe could handle :) . The magnets were 50mm tall, about 35mm wide, and 12mm thick. Being glued to a 6mm thick disc of steel, their output was enhanced, due to the magnetic circuit afforded by that backing plate. What's good about this design is that it does not impose any real load on the spindle, while it is beginning to spin up, which makes it better for use with a wind turbine :) . If I did this again, I would use a bigger disc, to match the base of the water heating vessel, and add more magnets.

[@elizjan4689]

This is a video in which someone tests this: kzbin.info/www/bejne/m4ukpKCEmrd4jqMsi=FC70LtGaE2L7rPVn And in this video, someone is building something similar from scratch: kzbin.info/www/bejne/epiboImIadBoes0si=NjFKTYlI4uWIKOiR I think this is a good idea, in which the elements practically do not wear out, but very expensive due to the prices of magnets.

[@paradiselost9946]

@@CNCmachiningisfun i did it as well about a decade ago. been a few channels try it with angle grinders and copper pipes and various efforts and you just have to laugh at them as they all missed the important aspects... WHERES THE EDDY CURRENTS? it seems a common theme :). 200mm backing plate off a big speaker, shallow 16mm pockets (no glue!). yes, enough to locate them, bridge the unused poles, but not enough to short the magnets out to themselves! i think it was 30 of them... alternating polarity neo magnets worked far better than one pole only. obviously! planned a spiral, somehow the g-code stuffed up and yeah... just a single row. a "brass disc"... not sure, i suspect its some weird copper alloy... but worked. could be better? could be worse? iunno! a leadscrew to vary the air gap and braking force. all pivoted for a load cell. then they banned motorised bikes here and i shelved it 80% finished and pinched the magnets and now its just rusty junk? my mistake was spinning the disc, not the magnets. oops. but this idea has been lurking in my head for a year or so now, and im looking at various bits of scrap again... i have to make a dyno anyway. about 100HP capable this time. hold the copper plate still this time and add water cooling!

[@CNCmachiningisfun]

@@paradiselost9946 Your new project sounds interesting :) . And, yes, it is nice to see that you properly understand the workings of these devices. When I developed mine, I couldn't help but compare it with the mechanical speedo in an older car, as the stator plate always wanted to take off, and follow the rotor. My next one will serve as a feedback system for engine RPM management, using the speedo mechanism.

[@jpeg1991]

Thanks Tim. I'm enjoying this latest rabbit hole

[@tracybowling1156]

I love when you have a big project going. And I love when you nicely prove how smart you are! You are a gentleman!

[@MikePerreman]

Your reasoning for using plates makes sense. While I still think it would be feasible to get the magnets up to speed, I agree that it would be quite expensive. The death of many ideas, lol I wonder if higher-viscosity fluid inside of the paint can would be able to convert more of the torque into heat.

[@wilsonlaidlaw]

Tim, I would suggest looking at a company called Kora in Germany, who specialise in making small mechanically driven heat pumps for wind power.

[@FishyBoi1337]

Heat pumps are a miracle, technology connections has explained it again and again a bajillion times better than I ever could!

[@assassinlexx1993]

Car air conditioner is much simpler. With a small compressor that is belt driven. The hot side radiator could place in water to heat or a fan to blow heat. Of course the cold side radiator will give cooling for summer.

[@23bcx]

If you are already treating the steal plates as consumable, rust is a good thing. Iron rusting is an exothermic reaction, it adds some minimal heat to the system.

[@everettrubel7112]

They sell those hand warmers that are just little bags of sawdust and iron filings that slowly oxidize when you take them out of the plastic packaging.

[@weldyboy-R-]

When I will moving the heavy iron in the water, I get warm. Just get into one jacket with a friend and take turns mixing after 12 hours for sleeping. We will be warm all winter without fuel. Just have enough food. Thanks, this one tip I was needed.

[@SimonHollandfilms]

great idea Tim. a Cambridge science friend told me to heat water with our large water wheel, in our mill. i went down the gears and electricity generator route and only managed to turn 4kw of water power into 50v at 1 amp of electricity...we should have heated water. i was going to stir water in an old lagged hot water cylinder snd pre heat the hot water in the house.....fascinated to see what is the simplistic method of friction heat. following your ideas with great interest

[@Brennannnnnnnnn]

Get well soon!

[@benjaminshropshire2900]

One up side to this project; converting energy to heat is literally the only thing you can do with 100% efficiency. If you want to keep things slow, consider a piston pump. Just a close fitting, but still leaky, piston pushed back and forth in a long tube should work. All the work needed to push the water thought the small space around the piston would go to heating the water. It would also have the advantage that it would be trivial to make it circulate water into a larger tank (or tanks). A little fun with an automotive type thermostat and you might even get regulated water temperature.

[@graemezimmer604]

Hi Tim. I'm glad you mentioned Induction Heating. It is probably the simplest of the "no contact" methods, and the need for high speed can be avoided by using a larger diameter. Even a large annular ring would do. (although there are many designs on the web for directly driven wind generators which have a relatively small diameter). But when you think about Induction heating, then it's only a simple step to generating electricity directly. Having your energy in electrical form has so many advantages. The obvious method is to use a surplus AC motor connected as a generator. You can pick up large motors for scrap metal prices. Further, if you don't need a precise frequency, you could do away with speed regulation. You'll find many designs on the web for people using AC motors as wind or hydro generators. Likewise there are many designs for home-made Generators using magnets embedded in wooden disks. I think you should definitely be thinking about homemade AC or DC generators to convert wind energy to heat. P.S. I still think that Solar electric heating is the way to go. I heat my small shack with a fairly large solar array, set of Lithium batteries and a heat-pump Air-con. Last night was down to about 3 degrees and my air-con was drawing about 300 watts continuous. And this morning the batteries were back up to 100% by midday. However the secret is very efficient insulation (double glazing and heat-exchange ventilation), while the payoff is perfect thermal regulation with zero maintenance.

[@bendordoy4815]

I did miss your comment about a heat exchanger in your previous video hence why I suggested a generator powered by the windmill and a heat pump, but I look forward to seeing you work on this idea and any others.

[@thetubbe_drawing]

Awesome series I can't wait to see the finished windmill friction based water heater

[@abigailpip112]

I hope you feel better soon Tim. Thanks for the video. Interesting. It will be good to have an independent view on heat pumps. I'll look forward to your investigations

[@everestyeti]

Know how you feel, had Man Flu three weeks ago and I'm still getting over it. 😂🤣 Hope your feeling better soon. 👍

[@bensiemers5094]

A mixture of glycol and water should eliminate your rusting issues and a screened settling chamber above your magnet may be helpful. Very interesting! 😊

[@gearhead1302]

Heat pump is a great idea. Also the commenter was right about the efficiency. It's calculated by energy used vs energy moved so it can be above 100%. The steel friction plate idea just creates too much particles and wear. Have you looked into the torque converters? Converters can generate tons of heat with mostly torque not rpm. The stall is greatly variable. Like your videos I will keep watching.

[@SteveBueche1027]

My in-laws use black tubing in a coiled fashion and have the sun heat to tube which in turn heats the water. An inexpensive pump would run it where needed and it stays clean. This is how they get a heated swimming pool at no charge. I hope you’re feeling better soon.

[@totherarf]

I see a tiny flaw in this one ...... Ireland! It is known more for its lazy rain (it goes right through you rather than around) as opposed to sunny days! ;o)

[@redoktopus3047]

Tim said he wants the heat mainly for the winter. I also mentioned this because they work great for heating water! I think he's dead set on the windmill route tho. Even if he would gain quite a bit of savings for most days when the weather is mild and the sky is cloudy. Solar Water Heaters are a thing in Ireland tho! But Tim is a guy who likes to do things himself :D

[@alaricsnellpym]

If you have a low RPM shaft, you can have a gear train bringing that up to high speed and then spinning some paddles and put the WHOLE LOT in a singke vat of oil. So you get the high RPM spinning paddles in oil, and all the losses from the gear train are just added heat into your oil (which is then heat-exchanged onwards) and wear will be very low. The water -cooled workshop air compressor idea in another comment is excellent, though, and basically asimple heat pump too :-)

[@dfishpool7052]

Hi Tim, thanks for the entertaining video - loved the bit where the plates gained weight - always knew Ireland was a place where magic happened! Get well soon; looking forward to the next stage of this adventure.

[@RealLuckless]

For the issue of needing an additional fan or pump along side the compressor to go with your heat pump option: You are building this to fit to a windmill that you want to use to concentrate heat... You can use the same 'fan' you're running your windmill with on your cold side, and your hot side fan can be whatever you were going to use to move the hot water from your friction generator. The sides of your windmill become your heat-capture 'radiators', warming your chilled fluid by allowing the same wind driving your windmill to blow over them and transfer energy into the system so you have more heat energy to pump out to your hot side. It may be more cost effective to build it as a relatively small refrigerant loop heat exchanger inside a larger brine tank/loop. The thermal safety wiring on things isn't really any more complex than you would need for your friction based machine - You do probably want something on there to monitor that your friction core isn't running dry and turning into a glowing lump waiting to fling itself apart after all... Remember: Every machine can become a smoke machine if you run it badly enough.

[@enterprisestobart]

This is a scaled down version of an idea I had for the 70MW range of turbines (using recycled truck/train/marine engines as the compressor). Also if the site is built over an old mine (preferably flooded) the heat energy can come straight from there (albeit better suited for district heating) If conventional vapour compression gas is not available, a humid air medium could be used.

[@londonnight937]

Tim, if you do end up building a windmill, make sure to make it huuuge. This way, it's going to be amazing no matter what.

[@timeflysintheshop]

Hey Tim! I know you want to invent and build, but if you manage to build the wind mill, you could get a heatpump style water heater (they are available in the USA) and drive the compressor with the mill instead of a motor. Then you would have a proper hot water tank from which you can use the hot water for whatever purpose you like.

[@spoder5043]

thank you for this follow-up video. the induction heaters may require high speeds, but there is less friction and torque required to drive them. I'm sure you already are aware of this, just wanted to comment this anyway lol. I'm still rooting for the generator though

[@rusty911s2]

Loving this and hopefully a nice distraction from man flu! I'm with you Tim, keep it simple, slow and within the whole windMILL ethos.

[@joshuadelisle]

I just had an idea for you. Why not a belt drive on a fixed pipe filled with water. The rubber belt or even leather will give great friction. It's also used as a method of fire by friction if I recall. Edit it's called thong friction fire method. Also you can roll a ring the width of the turbine and use that as the belt drive for maximum speed ratio instead of the slower drive shaft. Cheers J

[@wayoutwest-workshopstuff6299]

good idea Josh - except some of the heat generated would be in the belt, maybe? and be lost as the belt circulates?

[@joshuadelisle]

@@wayoutwest-workshopstuff6299 ah so because the belt moves it's constantly being air cooled while you're water pipe is constantly being heated. Seriously watch some tutorials on the fire thong. Also surely you've cut bailing twine with bailing twine, it's the same thing. I bet you'll get as good of heat with very little wear on your parts. Worth a try?

[@wayoutwest-workshopstuff6299]

Yes - always worth a try : - )

[@HenrikLaurell]

Very interesting subject!! Following with interest. Really hope you come with a good solution. In the summertime you could let water through tiny but long tubes placed on the roof or similar. When sunny the temp could get very high.

[@andypeter7537]

As you said in the film the term efficiency for a heat pump or refrigerator is misleading. Efficiency describes the output compared to the input. i.e. the proportion of the energy driving the heat pump that is responsible for “moving” the heat from the cold reservoir to the hot. You may have a 50W motor driving the compressor delivering 40W of work (80% efficiency) The coefficient of performance (COP)is the term that can be above 100. The 50W heat pump moving 100W of heat from cold to hot has a COP of 2 or 200%. Love the channel one of the best available.

[@yt650]

I find all of this information very interesting and hope it continues. I have one thing to add that has nothing to do with generating the heat. My suggestion would be whatever you want to warm up such as a home or workshop the first thing that you do is super insulated. I'm not talking about insulating beyond stupidity, I'm talking about taking advantage of every opportunity you can to keep the heat that you make within the structure. Many people do not realize that even burning wood for a heat source uses air inside your structure which you have already heated and you're using it for combustion and it's going up the chimney. In the case of using wood as a heat source, an outside combustion air source would be a good idea for your woodstove, pellet stove etc.. Keep up the good work.

[@Tater1337]

agreed, 90% of heat loss is thru air leaks, not from poor insulation values and probably more prominent in an area that has enough wind to turn a windmill

[@yt650]

@@Tater1337 If one turns on their clothes dryer or bathroom ventilation fan, air is blowing out of the structure and must be replaced by the ambient air and whatever that temperature is outdoors that is going to come indoors through every possible tiny leak. They have a mechanism for testing such problems and it is astounding where the leaks come from and most people including me would not have imagined.

[@Nelo390]

I fully agree with this! a few cans of expanding foam can go a long way. There are some expensive ways to pressurize a building and blow aerosolized silicon which then collects in small air gaps that air flows out through, but it's likely too much hassle for him, and too many thousands to bear. A good eye and can of spray foam would do much the same thing though, for a much lower cost.

[@yt650]

@@Nelo390 You are absolutely right . This is not something I thought of, I was taught this and this was proven to me. People do not think that once the air goes up the chimney for combustion or out through the dryer vent, it must be replaced by outside air through every crack. A dedicated source of air for combustion for example woodburning prevents this from happening.

[@Tater1337]

@@yt650 yet, I am amazed there is not more "cut your heating costs in half with this ONE SIMPLE TRICK" because yes, fixing air leaks works sooo well, guess how I know

[@D-B-Cooper]

I hunted down where they came up with the claim that a heat pump is 300% efficient. Turns out they call a toaster 100% efficient and the heat pump is three times more efficient. Moral of the story is not to heat your house with a toaster.

[@mtttony]

With a heat pump you only need a fan if you don't put out enough collector panels, if you have to small a collector like a heat pump designed for a flat or high-rise it will freeze without a fan but if you have space you can put out as many collectors as you like.. And the good thing is the collectors are very cheep.. you could even use large panels of of the back of drinks cabinet fridges.. Thank you keep up the good work from Tony in Glasgow..

[@Tater1337]

the goal is uses for a windmill, not heating water. also break the 3 rules of simple, easy, and cheap that he is following

[@henrikhv5084]

well, I learn from you, and I listen, so keep them comming. cheers from Denmark

[@sammusson5317]

I'd suggest using oil instead of water for the inner tank as I think rust will be more of an issue than you think. If you put the gears under the fluid as well then the gears are nearly 100% efficient as they lose efficiency through heat. Do as much gearing as you want under the fluid and you are not limited to metal on metal friction. I prefer the heat pump idea. See if you can pick up an old cheap freezer or fridge pump. Lot's of interesting ways of getting the heat to pump (air source, ground source , solar water heater, compost/manure heaps)

[@DrBorisIngram]

Good idea about reducing the number of energy conversions so using friction is a good wheeze imho. To increase it even more you make the rubbing surfaces rougher by pitting or some welding blobs or some such which will also wear but create more friction while it is rough. Also, if you add some weight to force the plates together, more friction too - the resisting force is mu, the friction coefficient, times the applied load - so if you squeeze the plates together, it will be harder to turn and generate more heat, but you must balance against the rotating speed - the work you get out is force times velocity, so a bit of experimenting to find a good balance. Good luck and get well soon

[@Tater1337]

you want the surfaces smoother, not rougher. maximum friction surface

[@feldbahnkanal8194]

When will the narrow-gauge railway continue?

[@schwuzi]

It costs too much money. You can donate to see it sooner.

[@carld3184]

I will vote for two different type systems: 1) a shaft driven air conditioning compressor connected to provide heating or cooling as needed. The air conditioning compressor shaft would be mechanically driven by your windmill with the reduction gearboxes mentioned by Kris in another comment here. The crankshaft rotation speed would not be very high so you would need a large volume compressor. It might be necessary to be able to connect more than one shaft driven compressor to the large driving gear or chain so that under higher wind conditions more heat can be generated and stored. Instead of commercial refrigeration gases you could use a mixture of mostly propane with some butane, study AZEOTROPE. The whole contraption would be located inside the rotating head of your windmill the heat that is generated would be transferred with a heat exchanger liquid, think about the hydraulic connections in an excavator. Yes, propane is flammable and explosive so precautions have to be taken. I built a home-made air conditioner using car antifreeze as the heat transfer liquid for our boss under his detailed instructions when a summer student in a maintenance shop in the 1960s. 2) build a very large circumference alternator that can produce significant amounts of electricity at slow rotational speeds using only copper coils and iron cores from used transformers, no need for large numbers of magnets.

[@covishen]

The science of thermal dynamics is almost magical. It's way beyond me. Good luck and I am really excited about what you cook up. Thanks for bringing us along!

[@boelwerkr]

About heat pumps. If you're only interested in the Heat itself generated by compressing gas. You can do it with a cheap air pump. No expensive gases needed. Imagine an insulated bicycle pump connected a one way valve (tire valve) to a water cooled turbo inter cooler (insulated) and a needle valve to the outside. The pump will create pressure and heat that will transferred to the water in the inter cooler and the needle valve will make sure the system will stay unter pressure to make the heat exchange effective. If my rough calculation is right, you will only get 125% to 150% efficiency this way. But that's just a bonus for you. You only need 5-8 bar to create quite a lot of heat. I remember melting (softening to the point of deforming) a cheap plastic bicycle pump in the heat of summer while pumping up a big tire.

[@rjung_ch]

Cheers Tim, I'll look at the article. 👍💪✌

[@fredrikb3543]

I totally love all the practical simplicity of all your projects. Ofc. there is more advanced tech on everything. And ofc. you can buy all tech and build it. But going back to some roots of engineering, taking the scrap that dont cost much or anything at all, invest time and thinking. Then come up with a project that is amazing to watch. Bake this toghether with some really charm talking and real knowledge. as I said I love it. Your videos inspire, Alot of the videos you made inspired me and gave me ideas. I am also sure that you really enjoy your projects and use your brain to make it as simple as possible to fit the needs you have. Thank you for your channel. It is very entertaining and soothing. I really hope this project continue in a form that suits your needs! Regards!

[@arandomvisitor6878]

suggestion: carve impeller like channels into the plates and use oil instead, should signifficantly reduce wear while also circulating the fluid for better heat transfer. don't know if it would be better or worse at heating though, on one hand the oil is experiancing friction on the other it might be less than steel on steel

[@coltmapes6075]

This is fascinating. I really want to know how an oil would change the outcome from the design you have.

[@michaeleitel7186]

Do you remember your steam machine cylinder? If you pump water through a small hole the energy you need for pressing is converted into heat. You only need a crankshaft (ball bearing) and the rod is pumping water in circle on the bootom of your mill. Use some screw (needle valve) to find the optimal hole diameter.....

[@IstasPumaNevada]

Thanks for once more patiently explaining your thought processes. :) I love the idea of a heat pump but I wonder how well it would work at the varying RPMs that would be provided by something like a wind turbine. And either way it definitely drives up the complexity and cost over just steel plates rubbing away.

[@lalala-oh8fw]

i was going to say this. friction based systems is the way to go. maybe not steel on steel but friction none the less.

[@victoryfirst2878]

YEARS AGO my neighbor made a friction heater using a dryer part of the washing machine. Worked like a champ. I was just amazed at the heat this made with very little electricity being used. I bet this technology is being suppressed by the powers that beeeeeeee. Nice video Sir. Hope you beat the cold, that usually SSSSUUUUUCCCCCCCKKKKKKKKKSSSSSSSs

[@AkkerKid]

What about a highly viscus oil or paste? Machine the plates to have tiny oil channels in them extending out radially and use the thickest oil you can find and maybe mix in a grease to thicken further. The oil channels will ensure there is a small gap between the plates once they wear in but then wear should dramatically drop off afterwards. Want more friction? Put a little pressure on the plate sandwich like a clutch. Want to run at lower RPM? Make the thing WIDER. Added benefits: it won't evaporate, it won't rust, great thermal properties, it could go above water's boiling temperature without pressurizing, the right oil can self-regulate to lower it's viscosity (friction) as temperature rises.

[@mitchamus]

Hi Tim- thinking about your heat exchanger design- what if … the last turning plate in the stack was slightly larger that the rest and on the outside, had some fins to create a centrifugal pump? You could then shape the container (the paint bucket) to have an incoming and outgoing port, to the circulate the heated water (or oil) around a heat exchanger coil inside the insulated tank? This would probably make the heat transfer more efficient. You might even be able to do away with the heat transfer tank altogether if the pumping action is good enough to run a hydronic heating system directly for example…

[@climberjb]

Another +1 for a heatpump. You can get the parts for cheap/free from an old fridge, freezer or air conditioner (although not that many of thoes in Ireland) and can get what looks like more than 100% efficiency!

[@Nico_0900]

what you also can do is using very viscous oil. that'll slow down the abrasion of the metal plates and increase friction by quite a lot. it should even be possible to not have the metal plates touch each other and still create a lot of heat when the oil is viscous enough.

[@tommfuller]

My door bike trainer uses rotating magnets rotating in an aluminium housing to convert rotation into heat. No rubbing or wear, and you can control how close the magnets are to the aluminium to control the torque…maybe second hand “turbo trainers” could be a useful source of parts.

[@tommfuller]

And they come pre geared to work at bike pedalling rpms …like 30-130 rpm sort of thing.

[@Nelo390]

I have seen cody's lab do a similar thing and it works quite well!! Magnets can be expensive and hard to get though, especially neodymium.

[@pgtmr2713]

Why wouldn't a generator be more efficient? A generator uses magnets to pull electrons through a metal, eddy current braking does the same thing. Except with a generator you can dump all the electricity into a load designed to create heat at one single point. Resistor, bulb, heating element.

[@paradiselost9946]

@@pgtmr2713 because a generator is NOT SUPERCONDUCTING. it has resistance. and its in parallel with the load. series? parallel ;) what happens when you have equal resistances? half the power is dissipated in BOTH. lenz law demonstration... magnet in a copper pipe. resistance is the pipe itself. the conductor and its induced opposing eddy currents. cut a slot in the pipe, theres no eddy currents, no lenz reaction. change the pipe for a coil. short it out. lenz reactions. eddy currents. wheres the voltage? you have to break the closed loop to measure it. you cant actually measure it. it doesnt exist. you only have current as a magnetic field and a "virtual" emf due to the resistance of that conductor. you put a resistor across... as it gets larger, more "open circuit", the voltage increases, you measure more drop across the load, as current flow through the generator AND the load reduces. you overlook that due to current flow, some power must always be lost in the generator itself. "jacobs law". your generator is only "efficient" if its of much lower resistance than the load, and the output of it is well below what it can actually deliver! if it were to deliver full power to an equal resistance, you could only transfer HALF the power, and the rest will appear as heat in the generator.. but that would actually be when its 100% efficient! efficiency is a bit like statistics, you have to be careful about WHAT theyre measuring and comparing ;) an eddy current brake on the other hand confines all that current to one conductor, and all that current appears as heat, due to currents through resistance. its like water brakes... you could make a water pump, hydraulics, the fluid, pump, and hydraulic thingy get HOT. but the task required that... say, i was running a pressure washer. or bobcat... excavator? whereas if i wanted to actually just make HEAT? or a dyno, a variable load to test engines? i would plumb the pump to itself and work on that, why do i need the whole excavator?

[@Rouverius]

Very cool! (sorry for the pun) Praying you feel better soon.

[@faragar1791]

If you're going to have heat exchangers between the liquid around the friction plates, and the water in the storage tank, you could put other materials around the friction plates to generate the heat. Maybe instead of water, fill the friction plate container with oil, sand, or salt. Solids like sand or salt could generate more friction and more heat at a lower RPM.

[@du7ch384]

Tim, just a thought but why reinvent the wheel spinning discs that generate heat with a friction material have been used on cars for decades it's disc brakes you could stack brake discs on a shaft and the callipers could give you a varying degree of friction spun up in water etc to transfer the heat, even the pads are "consumables" for ease of service. as a mechanic I usually think car parts, whatever you build will be amazing and cant wait to see it.

[@Allan_aka_RocKITEman]

Starting at about 05:50 in this video... I commented under the previous video about minute steel particles from those plates becoming entrained in the working fluid and being pumped around the system. The way you plan to set up your heat exchanger would eliminate the problem, although I presume the water would have to be emptied and refilled from time to time due to the buildup of metal in the liquid {even with a magnet in the container}.

[@emil62627]

If you want to convert your windenergy into heat the maximum efficiency you can achieve (without a heatpump) is 100%. So 1 Joule of Kinetic Energy into 1 Joule of heat. If you use friction you will almost immeadiatly arrive at this efficiency. The problem is you can only heat up the water near the wind turbine and thus you need to transport the hot water in pipes. This lead to transport losses. Depending on the insulation and the outdoor temperature I would not underestimate these. Heat transfer is proportional to the temperature difference. For example: 40C Water and 20C ambient-> 20C temperature difference 40C Water and 0C ambient -> 40C temperature difference and thus double the heat loss. You need the heat in the winter and thus you would have to insulate the pipes very well in order to keep the losses reasonable (or even bury them) - wich is expensive. The efficiency of typical electrical generators is about 80%, the rest is lost to heat. So if you would chase the highest efficiency you could liquid cool your generator (also use the cooling water for heating) and use resistive heating (like standard waterboilers or kettles). Then you would achieve the same efficiency as the friction solution. If you do not cool your generator and use resistive heating you still end up with a efficiency of 80% - because resistive heating is 100% efficient. But electricity is a lot easier to transport than heat. Just lay some cables and you can transport it with significantly lower losses than heat - without pumps and worrying about insulation or leaks or ….. Transporting electricity also gets more efficient the colder your cables are. And the cost of the generator (alternator of old car) + cables + resistive heaters would probably be the same or even less than the friction heater + heat exchanger + pipes + insulation. While being a lot more „comfortable“ To sum it up: due to transport losses when transporting hot water and cost of pipes and insulation I would assume that converting your energy to electricity and using resistive heating is the best option in terms of efficiency and cost.

[@OntarioTrafficMan]

Exactly. Tim says that converting energy types involves losses, which is true, but so do transportation and mechanical linkages. Although you lose up to 30% of the energy converting it to electricity, the rest of the process has negligible losses.

[@rodblod9526]

You also have to consider efficiency loss in the magnets at higher temperatures.

[@wayoutwest-workshopstuff6299]

I can't argue with any of that - but you're forgetting storage of energy. Heat storage in an insulated tank of water is a lot cheaper than a bank of batteries.

[@emil62627]

@@wayoutwest-workshopstuff6299yes of course. Assuming the house you want to heat already has a hot water boiler installed I would just use that for storage. In this case the energy storage for both methods is the same. If it does not I would still recommend storing the hot water inside of the house - this way any heat loss contributes to heating the home. Just because you use a different method for heating the water doesn’t mean you have to store it differently. But I totally get it - if you would want the simplest solution you would work a boring office job, pay your bills and don’t worry about anything but football. But this is clearly not the way you are - thus do what you would like and what is interesting to you. Best of luck with your tinkering 😊

[@aggese]

I agree

[@bigunone]

Tim doesn't think outside the box, he asks what box? Spent semester in college studying solar water heating, it is forgotten, with everyone one the solar power band wagon, it can be a fairly simple way to do such things as heat your house,

[@johnfreiler6017]

Get well soon, and do investigate the magnet idea at small scale before you drop it. I agree the heat pump idea is too fiddly for what you're looking to do.

[@hulkgqnissanpatrol6121]

In all the aquaponics, fishtanks ect I have always put some steel bolts in the tank's as when the colonised beneficial bacteria help break down the iron and over time the bacteria turned the souroundings into a iron sludge. The same happens inside car radiator's ect. You'll always have some kind of erosion. The magnets spinning past blocks of copper can get so hot it can melt aluminium and have zero affects on longevity ect.

[@thebeautifulones5436]

Instead of all steel friction plates, use aluminium. The aluminium oxide will be worn away and the pure aluminium metal will oxidise and release a lot of heat and also hydrogen from the water. All very complicated though. I myself have bought 3kW of used PV panels for $100 and use them to heat water with an old kettle element. No MPPT or inverter is required.

[@zacharybowers3]

Have you thought about using a Savonius wind turbine for your traditional windmill house? By incorporating a 90-degree conversion to a central shaft, you could directly drive a spinning disk. This design eliminates the need for belts, simplifying the system and reducing potential maintenance issues. the disk would be quite large, and the tank would have to be engineered for the shaft to go through the middle. then you would have your subfloor just above. you may not even have to circulate the water to heat the first floor. I would have to draw this out to explain. would take a very large perfectly weighted disk.

[@PatGilliland]

A couple of thoughts Bigger plates to reduce the rate of wear A more viscous working fluid to increase the overall friction. Motor oil full of metal bits might actually be more effective.

[@thedave7760]

some type of adjustable spring to compress the plates would allow you to use all the torque when the wind changes. If it's a not so windy day then lessen the tension on the spring to keep things running then when the wind blows you can tension up the spring to get the most friction.

[@lalala-oh8fw]

And then use a ball type govener like on a old steam engine to adjust the spring pressure on the fly

[@msx80]

We're just one latent heat mention away to become Technology connections

[@rosseastman2134]

For a source of cheap magnets - perhaps you can find a school or business with a lot of old IT gear. Spinning hardrives contain a couple of very strong magnets, and the drives themselves are practically worthless after a few years service - I have 10 knocking around right now that are just essentially waiting to be destroyed securely, and that's just one nerd's worth!

[@mrclaus859]

Thanks for posting

[@gonzo_the_great1675]

Even crappy alternators can be 60% efficient. And resistive heating is 100% efficient. My gut feeling is, lot of energy is going to be lost bringing mechanical power down to the ground. So an alternatior in the head would be technically the best arangement. But where's the fun in that. Wonder if a cheap low power heat pump idea could be made from a fridge compressor system. Run from generated power. A bit of care taken in removing it intact and pressurised. Though you are only going to get low temps from it. But could make a preheater for another system.

[@kasbakgaming]

The main problem I can foresee with the friction heater is in the exchange. It certainly would work to heat up water, as your clever testing shows, but how efficiently can that heat be exchanged into the water you actually want warmed up? That's an open question, and I think perhaps you might need to run a second experiment with a primary container that is sealed up a bit better than your first paint can test, and place that into a second container to see how well it heats (of course the best exchanger will be one designed to maximize surface area, but this basic set up would work for a test). Other methods like electric might lose some efficiency in the conversion, but would that end up being more efficient over all because it could heat the water directly? Again, that's an open question. I am intrigued by the idea of a wind powered heat pump. The main question there is whether or not you can get a high enough pressure. If you were curious to try it, old school heat pumps used ammonia for their exchange gas; still a potential for danger when under pressure and breathing, but certainly safer and cheaper to obtain for testing purposes than other refrigerants. Since you mentioned induction heaters, would there be any reason you couldn't do that in combination with the friction heaters if you're using steel plates? Perhaps using electro magnets rather than rare earth magnets? If you do end up trying a design like that, consider if you can make a double shaft and have the plates rotating one direction while the magnets rotate the other, you're effectively doubling your speed without having to make the contraption actually spin any faster.

[@Gersberms]

Here's another crazy idea: what if you used one of the high-speed options, but put the step-up gearbox in the same water vat you're trying to warm up? That way any heat generated by those gears isn't actually lost. Since gear boxes are often sealed and lubricated units, I wonder if it could operate under water.

[@davelowe1977]

I think friction heating is a bad idea. Personally I'd calculate the max energy from the wind using an appropriate equation, then size the othe components to suit. I'd either use an old torque converter or a dynomometer and a heat exchanger from an old combi boiler. They're ready made and available at scrap prices. Vibration and throw will destroy your primary side container and a single plate exchanger system will not transfer any useful energy.

[@TAWithiam]

I can think of only one heat pump setup that'll meet your requirements. Traditional heat pumps use hermetically sealed compressors require making electricity, however, you could probably pull the entire air conditioner out of a junked car. They are belt driven at not particularly high speeds (using a mechanical seal rather than being hermetically sealed) and would probably do the job. You can just dunk the hot side radiator in a cooler and pump water through that cooler.

[@fishyerik]

It is somewhat complicated to generate power, but that also has a lot of advantages, like more ways to optimize output to varying wind speeds. Also, power is always useful, even when the heat storage is at capacity. Using the power to pump heat pump can make the heat gain more than compensate for additional transmission losses. Gearing to increase speed can be done in few steps with large gear ratios. Although generating power, and then use a heat pump is "involved", I wouldn't be surprised if generating meaningful heat more than occasionally by friction, without having to manage the system very frequently turns out to be more difficult in practice. Motors that can be converted to generators and heat pump systems that could be use after some modification/repair and refill is discarded every day. That said, I'll be more impressed than surprised if you manage to make a reasonably practical system based on friction.

[@DielectricVideos]

The whisk, impeller, or orifice designs might work well at low speed if you use a high-viscosity working fluid, such as a gear oil. A non-newtonian fluid such as cornstarch suspension might also be useful, and could even serve as a sort of speed governor for the wind turbine. I also like the heat pump idea, as if the coefficient of performance is 2-3, then the powertrain and electric generator (assuming electric drive) could be as little as 50%-33% efficient and still break even with direct friction heating.

[@HansWeberHimself]

Hope you feel better soon!

[@unusualfabrication9937]

if you are going to do plates, make sure to preload them against each other, so there is always a certain amount of pressure ensuring good contact. also, friction is proportional to normal force (in this case, clamping force btw plates)

[@WowCoolHorse]

I was down on the metal on metal at first, but I think if you filled the tank with a mineral oil (or maybe even just used motor oil?) that would make the system last longer, and maybe even generate more heat due to the higher viscosity of the oils instead of water. All you'd have to do is have a little magnet in there to collect all the rust and other bits, to keep them away from jamming the whole thing up

[@AutomationKing9]

All you really need is a state change material or in other words something that you can cause to condense and then boil under controlled conditions. This is how most cooling systems work and is exactly how heat pumps work. If you get a pump and a valve/backpressure regulator along with two air tight containers piped together you can make a heat pump to gather heat from the air around one side of the unit and transfer it to the other side and into either air or liquid. You can technically do this with water if one of the vessels is under a vacuum but it would be easier to use a substance that is liquid at the desired temperature when under a specific amount of pressure. Something like propane is a great example, at ambient pressure it is a gas but if you compress it to 2-3 bar it will turn into a liquid again. The higher the pressure the hotter it can be when it is a liquid. Also of note is that you can do this with air as well in a closed loop with just two heat exchangers, one on the high pressure discharge and one on the low pressure suction with a backpressure regulator in between. Just compressing the air will increase its temperature both through friction from the compressor and because during compression you’re adding energy to the air. The first heat exchanger transfers the heat to your water and then you go through the valve to the low pressure side of the unit, which will drop the the temperature of the air by around 17 degrees c for every 1 bar of pressure drop, you then use the other heat exchanger to transfer ambient heat energy to the air and then it gets re compressed and continues the cycle. You can also do this with a non sealed system where the air is just released out of the valve after going through the first heat exchanger. The goal is to have the compressor never stop operating so you’re always flowing the air. If you add a liquid cooling jacket to the compressor you can also scavenge that heat while cooling the compressor in order to make the whole system that much more efficient. If you want more details or just want to pick my brain on anything let me know. I’m a controls engineer who works with industrial equipment and high horsepower compressors as well as a tinkerer who likes to solve problems from new angles because “that’s the way we’ve always done it” is my least favorite excuse to do something.

[@replikvltyoutube3727]

I think opting for more thinner metal pieces would be better. You have to consider that thick metal is mostly metal in your mechanism, and thin metal will be more water. The only thick one may be the top one to compress them. Another thing for compression maybe bolt the stator plates together. I would coat a rotor shaft in some kind of plastic or heat insulator material to not wick out the heat.

[@RubyRhod]

If efficiency is your goal, generate electricity directly on the main shaft - at 20 rpms. Using some sort of wooden gears to turn the axle downwards, making heat with friction and somehow transporting this heat may be the most inefficient way, even more inefficient than anything else you explained. again: electricity at the main shaft, transport that with >99% efficiency to where you need to heat and voila - done.

[@Tater1337]

I know of no generator that can generate at 20 RPM besides, violates the cheap, easy, simple requirements

[@RubyRhod]

@@Tater1337 (bike) hub dynos do. So there is that. But they are usually limited to about 5W of power. But there are tons of generators available that can deliver way more power at low rpm. Keep in mind steady voltage or the wave form of AC just doesn't matter (but usually does in other applications).

[@PermireFabrica]

Tim, I really suggest looking further into induction-based solutions. I bet, with a few copper plates and some magnets, you have already more friction torque than your metal on metal solution! If you don't believe me, use a magnet and move it in front of a copper plate, the force is really surprising. As the easiest solution use an electric motor (one with permanent magnets) put the whole motor in the water and short the leads. Simple but effective.

[@radioroestig9638]

technically you don't need high rpms for most of the alternative heating methods you mentioned, you need high surface velocity. For induction heating, you could either spin a smaller disk really fast (with efficiency loss in gearing), or a large disk turning relatively slowly. What would a 1 meter diameter steel disk do, turning at 400 rpm, through a strong magnetic field?

[@Tater1337]

got he 400 or so magnets he'd need? he pointed that out

[@Nelo390]

@@Tater1337 He's pointing out having the magnets stationary outside the wheel, so you'd need less.

[@Tater1337]

@@Nelo390 then you get into the whole nightmare of coils on the moving part, slip rings, cost of copper, and all sorts of other issues. still need magnets, still need copper wire, and you need to engineer a sturdy enough frame to get the air gap between the two significantly small enough to reduce losses I highly suggest everyone read "HOMEBREW WIND POWER" By Dan Bartmann

[@Spedley_2142]

You'll lose more energy bringing the power down from the top of the windmill than you would installing a generator at the too directly. Also, almost energy losses are to heat so not really a loss if you can keep it contained.

[@andrewt9204]

The only loss of a generator would be the generator itself if you were heating with a resistive heating coil. Generators are usually around 87-92% efficiency, the resistive coil is 100% efficient at turning electricity to heat. Plus you also gain the benefit of being able to charge some batteries when water heating isn't needed.

[@LincolnSayger]

I'd think a Sterling-engine-type heat pump would be fairly elegant. They don't have a lot of moving parts, and the compressor is the pump for moving air from the hot side to the cold side and back. I'm no engineer, though, so I could be wrong.

[@thebokworm]

with your issue about the speed of the magnets, you could achieve those high speeds with flywheels it also could just be large flat discs use the 400 rpm you might have free from the final drive of the windmill itself, and onto a fly wheel and it might be a fast enough speed at the edges, the heating plate could also be hollow, less to heat as well

[@jamesdaniels4774]

How about using the turbine to power the flywheel on the compressed air engine! And use that as your compressor. As for gearing maybe a belt or chain drive would be more efficient way to get a gear ratio and transport the power down the ground level

[@shofixi1316]

Problem with heat pumps in winter is where do you pull the heat from? The cold outdoors ? I would look into Dynamic Heat Generator.. Love your content Cheers

[@PatGilliland]

There's been some success with drilling below the frost line to get to soil or the water table that's warmer than ambient. Not classical geothermal of course but same principal over a smaller thermal gradient.