A setup and demonstration guide of motion detection on Hikvision CCTV
Пікірлер: 112
@sasak52625 күн бұрын
Thanks mate, it really helped me a lot. Greetings from Sydney Australia
@glenchallis3281 Жыл бұрын
Thank you DAC Security, very helpful explanation of how to setup Motion Detection !
@DIY-UK2 жыл бұрын
that is very informative, really good presentation, thank you. i will set up my system in similar way.
@kwameohenedanso1272 ай бұрын
Great
@garyj21433 жыл бұрын
Very informative and really helpful. Thanks for the information/assistance provided 👍
@Linux4Ever20113 жыл бұрын
Excellent demonstration, thank you very much.
@1976kona3 жыл бұрын
Thanks what a really helpful video , I was struggling with notifications, all sorted now 👍
@pauld7803vvvrtyt2 жыл бұрын
Watched several videos on Hikvision's MD and have to say this is by far the best, so thank-you. Just one question though, not so long ago whilst setting up motion detection some of the squares within the grid used to go red when motion was detected, which made things a lot easier for removing bushes etc when they blow in the wind. I seem to have lost that facility now, can you throw some light on this please and how to get it back. Thanks again guys.
@DACSecurity2 жыл бұрын
You can’t turn the red squares off so seems strange it would disappear. Maybe try putting the squares in the whole picture and see what happens if picks things up again. Possibly there’s no movement or sensitive is very low and not detecting. You could switch the recorder off and back on again to see if that helps. Thanks
@pauld7803vvvrtyt2 жыл бұрын
@@DACSecurity Thanks for taking the time to respond, its appreciated. I had already tried everything you mention and more. Including making sure Dynamic Analysis for Motion is enabled. Im using the DS-9632NI-I8 running V4.61.000 build 220507 if it helps. I've also tried via the web using the local IP address of the NVR, IVMS 4500, the NVR itself and even the camera's individual IP addresses. And whilst I can clear the red squares ok for each camera and then choose the areas I wish motion to be picked up by clicking on the pertinent squares, it still doesnt show any movement like it used to when motion is detected. The other settings havent been touched including the sensitivity which is 60. I'm pretty confident you guys will work it out as I'm at a complete loss now. Thanks again.
@DACSecurity2 жыл бұрын
Is the tick box enabled on each camera to switch motion detection on?
@pauld7803vvvrtyt2 жыл бұрын
@@DACSecurity Yep, all ticked. As mentioned above, the motion detection is working and I'm able to highlight the squares I want the motion to be picked up and remove the areas I don't. But crucially I want to be able to view certain areas to see if motion is detected or not before removing them. I'm wondering if the latest firmware versions have removed this facility, although there's nothing mentioned in the notes Hikvision disclose associated with each firmware update. Thanks again for your assistance on this matter. Also can you guys supply the latest IP camera's that HV have released?
@pauld7803vvvrtyt2 жыл бұрын
Just to also confirm the settings in the Arming Schedule and Linkage Method within the motion section appear to be ok. The arming section is completely blue and I have A->1 ticked within the linkage method and D1 ticked, being the camera name. I'm not entirely sure this would have anything to do with my issue however.
@micaicm97478 ай бұрын
Great videos any help with line not a grid set up for motion detection - is there a video on this please
@Aleziss2 ай бұрын
Why it's not possible to set continuous recording WHIT motion? It would be super easy to find events on the time line and at the same time have 100% recording...
@ChaosDragonYT Жыл бұрын
I have the same device but i have a problem i live in a apartment and there is some lights that light if someone is walking and that is causing my camera to send me a alarm thinking it was someone any tips ?
@DACSecurity Жыл бұрын
A difficult one tbh if the light is motion activated as it will see the changes. All I can suggest is decreasing sensitivity, decrease the amount of squares and scatter them about. Apart from that not much else you can do
@kyngsley1 Жыл бұрын
Good video. I have nvr DS 7616NI-Q2 7 Camera HNC 344-XD. I can't seem to intrusion or cross line motion to enable. After enabling and drawing box or line when I click to save I get invalid operation. Can you please advise
@DACSecurity Жыл бұрын
Not all cameras and machines have the ability for line crossing etc , thanks
@bobmanp86532 ай бұрын
whats the difference between event and motion?
@MrTs123453 жыл бұрын
THANK U
@Chichilcitlalli2 жыл бұрын
what is the distance that the motion sensor can cover? i have heard that it is very short, the object has to be only a few feet away for it to work otherwise it won't detect any movement at all
@DACSecurity2 жыл бұрын
No not true. I'm not sure on the distance but it can be very sensitive to the point its far too sensitive. There is adjustment settings to decrease and increase as required. Thanks
@Chichilcitlalli2 жыл бұрын
@@DACSecurity yeah, the argument is not about sensibility, it's about distance, yeah it can be very sensitive or not at short distances, at longer distances it just stops detecting moving very well.... say at 20 feet....
@arendelle_ok2 жыл бұрын
when i use this software. and with my own webcam. will it works ??
@rowanmoore4824Ай бұрын
Hi I am using HIK Vision HVR which is using HVR 4.0 interface. Not all of the interface screen is visible, the edges are partially missing sides top and bottom. I have tried changing the aspect ratio on my TV but it doesn't solve the problem is there a setting for this adjustment in the interface? Fingers crossed you can help.
@DACSecurityАй бұрын
@@rowanmoore4824 you can adjust the screen resolution in the DVR / NVR menu also This will be the section you need to change it to fit
@DACSecurityАй бұрын
Click the cog on the top bar and look for VGA/HDMI Resolution and adjust as required. Remember to click apply after. Adjust until you find the correct one Hope that helps you Cheers
@rowanmoore4824Ай бұрын
@@DACSecurity fab all sorted. I also used you motion detection video to set it up it was spot on. Thanks for your help 👍
@PokoTomy Жыл бұрын
Hi, Do I have to buy a Hikvision camera, which has motion detection on own, or it doesn't matter, and the DVR will do its own work (if the camera doesn't have recognition feature)? Thanks, Tamas
@DACSecurity Жыл бұрын
It’s built in the dvr so any camera will work
@ThirumalaiAPash Жыл бұрын
Hikvision 7a08 model supports this?
@garyj21433 жыл бұрын
Can you constant record and also enable/run line/intrusion detection (run them in parallel)? Whilst still continously recording?
@gjorg1024 Жыл бұрын
I have the sensitivity set to 20 and it still picks up every bit of movement, rain , bugs , wind dust etc especially at night. Any tips or advice to fix this issue ?
@DACSecurity Жыл бұрын
Make sure the camera is clean, no spider webs Also on the grid part where you set the areas up, use less squares and spread them about
@gjorg1024 Жыл бұрын
@@DACSecurity thanks ! My setup is different I don’t have the grids, I have to draw the motion area.
@willdomenik88662 жыл бұрын
Another question, if i may, I really appreciate these videos on the NVR 4.0. I have a question, if I set up an Admin password and then additional users accts, is there a way to "lock down" the cameras, that i added for viewing? What happens now, i have 50 cameras out of 200 that are on several "pages" and sometimes my team will accidently hit a camera to view and it moves off that page and onto another, which in turn creates a domino effect, where several cameras have been moved from their original page. I then have to place the cameras back to where they were originally. Is there a way to prevent this?
@DACSecurity2 жыл бұрын
Yes I know the problem as someone in our office keeps doing the same. sadly I’m not aware of a way to stop this. It bugs me rotten also as there not keeping the flow I want.
@DogScreenTV Жыл бұрын
Can you run the full recording AND motion detection at the same time?
@DACSecurity Жыл бұрын
Yes
@bobwaterfield72223 жыл бұрын
Nice video. Do you have one showing how to set up a PTZ camera movement when a Bullet cam detects motion? I have that same NVR firmware (4.5) in my NVR thanks
@DACSecurity3 жыл бұрын
Not at the moment sorry
@willdomenik88662 жыл бұрын
Good day, question to ask, on setting up the Motion detection area. If i place the grid on a door, & setup the schedule, will I still record the whole area as it did before or will just the door will be recorded? (I will still need the whole area recorded as before). Thank you so much for this video. Really helps.
@DACSecurity2 жыл бұрын
Hi , it would only record the grid area. Are you setting up a schedule for the notifications?
@willdomenik88662 жыл бұрын
@@DACSecurity the schedule has to be 24/7, unfortunately the area surrounding this door must also be recorded. I have several cameras on other doors with the same setup, door and areas must be recorded and the added inconvience (lol) there are always people milling around these sites.
@willdomenik88662 жыл бұрын
@@DACSecurity Thank you so much for the quick reply.
@DACSecurity2 жыл бұрын
What you could do is set the camera or cameras up for continuous record so it records the whole picture all the time. Then switch on motion detection also using your grid and the grid area will send alerts to your phone. Hope that makes sense
@DACSecurity2 жыл бұрын
Watch the video from 6:30 and select your camera and put to blue continuous. Then switch on motion detection where you create your grid and alerts. This will record everything and use your grid for notifications when people around
@johnloftus42853 жыл бұрын
How do I get rid off the bleeding on my hi look when go on to system click it then go into event enable its starts bleeding how do I turn the bleeding off or down please fantastic system but driving me mad
@DACSecurity3 жыл бұрын
I've never used hilook so not to familiar with the software but you will probably have to find the section within motion detection and untick audible noise and apply it.
@johnloftus42853 жыл бұрын
@@DACSecurity yes I'm sure there is my friend will have a go again soon thanks for getting back to me
@xunit942 жыл бұрын
Hi, is there a way to have constant recording WITH motion detection so I can get notifications while the camera records everything around the clock?
@DACSecurity2 жыл бұрын
Yes of course. Go to the video at 6.33 and keep all cameras set to the blue colour so there in continuous record. Then go to motion detection and tick the box to turn on and setup your motion areas as per video. Hope that helps.
@blogdosaulo3 жыл бұрын
Hi! Thanks! In my Hikvision DVR the option "Motion" and "Event" are recording equal. I would like recording only "human bodies" on "event" option. How I fix that?
@DACSecurity3 жыл бұрын
Is it an Accusense machine ?
@blogdosaulo3 жыл бұрын
@@DACSecurity Yeah! On the "event recording" option, DVR records all motions equal "motion recording". However the alarm only sounds when human bodies are detected.
@chihuahua_mama_1984 Жыл бұрын
Hi there, was wondering if you can help me. I have a Hikvision DS-7608NI-I2/8P NVR. Last Friday my security company was at my house swapping it out for a new one and they must not have set the date right because yesterday I went to play back footage and it was saying it was Tuesday, October 18 (when in fact it was Monday, October 17). I reset the date yesterday at noon to Monday but the problem is when I go to play back today Tuesday, it is showing me yesterday's footage (I guess because it was showing as Tuesday yesterday morning until lunch). When will the recorder catch up and record in real time or is there something else I need to go? Live play is showing the correct day and time as of noon yesterday, Monday 10/17. My security company is absolutely terrible and are of no help but as a last resort I will make them come back out.
@DACSecurity Жыл бұрын
Options are you leave it to record until the hard drive is full and re-records over itself or you wipe the hard drive completely and it will all start fresh with the correct date from the beginning. As it is it will always show the wrong day until is recorded back over that day . Best just to leave it as is and it will sort itself out. Thanks
@chihuahua_mama_1984 Жыл бұрын
@@DACSecurity The NVR started recording correctly yesterday at exactly the same time I updated the date the day before.
@renebernhardtangkilisan96842 жыл бұрын
hi can it recorded when motion detection only ? what type of NVR Hikvision do you using ? Thanks DAC SECURITY
@DACSecurity2 жыл бұрын
Yeah thats what the video is showing you how to setup. It's DS7200 Series DVR . Thanks
@zacharygonzales2543 Жыл бұрын
how can I capture the pics and videos on my phon
@DACSecurity Жыл бұрын
kzbin.info/www/bejne/hmHZZ2qvfdGEqrM
@justintemp3 жыл бұрын
Which app is that? I have ivms 4500 and there are so many false. Positives
@DACSecurity3 жыл бұрын
This app is procontrol+ but you can also use hik-connect. There has been a couple updates to the app since this was made so may look a little different. Thanks
@justintemp3 жыл бұрын
@@DACSecurity any plans to do updated vid? I can't seem to get rid of the false positives
@DACSecurity3 жыл бұрын
We will do but we have other videos in the making just now. Thanks
@justintemp3 жыл бұрын
Which hik app is it as I cannot see hik-connect in the app store... Do you have a link?
@DACSecurity3 жыл бұрын
Hik-connect was removed from the app store but you can get it from hikvision website
@chihuahua_mama_1984 Жыл бұрын
Hi, I am getting error messages when trying to share or download and view downloaded mp4 clips from my Hikvision NVR. The only way I can view the clips is within the Hikvision app or directly on NVR. How can I download a clip and share it to someone on via text message to view on their iphone and how can i email a clip for someone to view on their computer? These seem like basic functions. Please let me know if you have any ideas.
@DACSecurity Жыл бұрын
If the clip is on the pictures and videos section on the app you can send via WhatsApp or Facebook messenger The file will be too big to send by txt or email
@DACSecurity Жыл бұрын
The part you mention mp4 file, is that when you have downloaded onto a usb stick? Try downloading a free software called videolan and you should be able to play using that software
@chihuahua_mama_1984 Жыл бұрын
@@DACSecurity hi there, cannot send via facebook messenger, error says "unable to send to messenger". it's not that the file is too big, I think the file format mp4 is the problem.
@chihuahua_mama_1984 Жыл бұрын
@@DACSecurity no, the mp4 is what I am getting when I try to email it or text it and then its unplayable
@chihuahua_mama_1984 Жыл бұрын
@@DACSecurity I'm really wanting to be able to text clips I download from the app and them be playable on an iphone, is that not possible? this seems simple
@damirsvegovic7162 жыл бұрын
what android sw do you use ? there is no standard HIK SW ? ims 4200
@DACSecurity2 жыл бұрын
Do you mean the app on my mobile ? If so it’s procontrol+ or Hik-Connect. What you see on the tv is just the software the DVR comes with
@mattjames88 Жыл бұрын
Had to turn mine off as wind and rain was setting it off every 2 mins
@DACSecurity Жыл бұрын
Depending on the machine you have the newer models have human and vehicle detection so eliminates a lot of the false alarms
@defaultgreen3 жыл бұрын
Hello. I need my Hikvision to beep the whole tone during the movement. Otherwise you just sleep through it 🤷♂️
@DACSecurity3 жыл бұрын
I can't help you on that mate. It only beeps as you have already heard.
@Jerryclinton8873 жыл бұрын
What if it does not work
@jeeteshsingh94523 жыл бұрын
Hi there - is GUI 4.0 a PC app? Or is this something which is installed on the NVR box?
@DACSecurity3 жыл бұрын
Its the user interface on the machine, so basically the software menu
@jeeteshsingh94523 жыл бұрын
@@DACSecurity cheers mate. I have a Hikvision DS-7616NI-K2/16P NVR. How can I get this GUI 4.0 installed on it? Do you have any video on this which I can view?
@leomerino39063 жыл бұрын
Is it possible to have 24 hrs recording along with motion?
@DACSecurity3 жыл бұрын
You can do it that way and use the motion to send the alerts
@minime18jd3 жыл бұрын
Does it detect dogs in backyard?
@DACSecurity3 жыл бұрын
Depends what model machine you have. The new machines have human and vehicle only detection but the older models picked up everything and usually stuff you didn't want
@nickg20273 жыл бұрын
hi, instead i get to draw an area? I cant get the grids? Thanks Nick
@DACSecurity3 жыл бұрын
Thats the new model you have. I will be doing a video on that shortly. You basically draw the area or areas you want to cover by created boxes or other shapes. Just make sure you right click the mouse to join the boxes you make. Hard to explain but hopefully helps a bit
@nickg20273 жыл бұрын
@@DACSecurity I will keep an eye out for that one, im hoping to set a zone within a zone to beep when someone enters
@DACSecurity3 жыл бұрын
@@nickg2027 I will try sort it next weekend.
@nickg20273 жыл бұрын
@@DACSecurity awesome thank you!
@kenfoster30182 жыл бұрын
Thanks. Right clicking the mouse, that's what l'm looking for.
@murry0012 жыл бұрын
You get a weeeeeeeeeeee film clip on your phone
@mcgourtyplastermouldings14423 жыл бұрын
What model number is this please?
@DACSecurity3 жыл бұрын
Its a DS7208 the last 2 numbers depends on size of machine. 08 is a 8 camera machine.
@mcgourtyplastermouldings14423 жыл бұрын
👍
@mcgourtyplastermouldings14423 жыл бұрын
Can you draw 4 line crossings and 4 intrusion box’s on this model?
@AMCSecuritySolutions3 жыл бұрын
hello sir please confirm me 7108HQHI-K1 compatibilit