MotoGadget Bar End Mirror [unbox and Install]

[@Mounty2010]

At 09:58 you say, if you take off the extra shell, it will fit in, but you can not tighten it. I think you missed, that you can tighten it using the screw under the black end cap. Tighten this screw will "spread" the slotted shaft of the adapter, until it sits tight in your handle bar. It does not matter if you use the optional adapter shell or not. The shaft and the shell will spread, thats why they are slotted.

[@garyholloway3327]

Hey Mike, greetings from over the pond. Just bought some Motogadget bar end mirrors for my Low Rider S and after reading the instructions, I really wasn't sure how to install them. After watching your video, you've made it all perfectly clear, even down to modifying the spacer if I need to. Brilliant! Thank you so much.

[@LifewithAnnaBee]

You really do make everything look so easy! 🥰🙌

[@ClutchFirst]

Oh, how I wish that was the truth. On a good note, every minute spent during production is a pleasure. 😊

[@marcusmartin3308]

Hello , Where do I get those black screws for the brake and clutch reservoir once taken off the mirrors? Thanks

[@ClutchFirst]

You can some generic ones online or Amazon. A pair should run you about $10.

[@markdunbar8219]

Been searching for bar end mirrors for my zh2 for a wile think these are the ones 😁 great review they look awesome thanks Mike greetings from the Uk 🇬🇧👍🏻

[@dieseldad60]

What screws did you put back in for your reservoirs? They weren't the same ones that came out and the right side one is reverse thread so not so easy to find. Any hints as to what you put in there would be greatly appreciated!

[@ClutchFirst]

It would have been a rough season without these motogadget mirrors. No more elbow action when overtaken in traffic.

[@Robostever]

Is there any vibration to the mirror at highway revs?

[@governordnyce3244]

My dude Mike back at it again. Great product reviewed by the best in the game. 👊🏽

[@ClutchFirst]

Thank you DNyce. I’ve still got ways to go in the KZbin game. 🙌🏽

[@Twoclickchris]

What screws did you use to replace the long stock screws with ?

[@Itisallagame]

Yeah where did that short screw come from?

[@Luna_cy8]

Yeah so bullshit to not explain that

[@Farhan.DucatiS1k]

how are these to the CRG bar ends I am trying to decide..

[@MrKingJavo]

Where did you get those replacement mirror screws from?

[@_AnanasIEgenJuice_]

For direct mounting on OEM bar end weights. Do you have the max diameter of the inner clamp of the mirror? Basically how wide a bar end weight can it mount on? And also if you could give an estimate to how low a diameter bar end weight it can mount and tighten down on?

[@Evil.Industries]

3 videos on these mirrors and still no install on the hyper. I guess that leaves room to make a 4th, 10 minute video 😂😂 It's all good, I'll figure out if I need extra hardware or spacers when I pull the guard off.

[@ClutchFirst]

The install starts at 6:41. I laid out time stamps in the description. The intention is to give information not mislead. Thank you for watching and welcome to the channel.

[@jairomotovlogs]

Great video Mike! Could you tell us what screws you replaced the OEM mirror/reservoirs screws with? Thanks!

[@ClutchFirst]

You can find some generic ones online or you could check Amazon. A pair runs for about $10.

[@jairomotovlogs]

@@ClutchFirst Thanks for the response, I know the bolts were Metric 8x1.25, however it went on fine for the left side (clockwise to install) but I think the right side is actually a different thread pitch as it’s not going in (counterclockwise)

[@dblhelx]

Yet another great video! May I ask where one can get those stock mirror hole block off bolts? Thank you!

[@timdrazba9489]

What size screws did you put back in your reservoirs? Dimensions? I know one has to be a right thread and the other has to be a left thread, but can you tell me where you ordered them?

[@dhruvzeevlogs]

Hi brother, Where can we get it please give the link to buy it.

[@huythai7326]

Nice videos. I have a question about the adapter. Does it fit the threaded handlebar? I am thinking of purchasing these but not sure it works on threaded handle bar. Btw my bike is yamaha fz 07

[@jonathanlin2583]

So sleek looking. Another amazing video sir! 🙌

[@ClutchFirst]

The video does not do these mirrors justice. They are super thin and stylish. Thank you for watching Jon.

[@Jason-hk4uq]

What was the torque spec you used for the silver bolt that adjusts the mirrors?

[@brettsewell701]

Are those plugs in your bar end weighted. They should be to cut down on handlebar vibration. I have these mirrors but not fitted yet as they don't work with my weighted Rino bar ends

[@楊文良-i5k]

Excellent jobs

[@gregreynolds9708]

Nice vid, camera work too. TMI about the packaging IMO. Brown box equals cheaper cost? Love the shirt.

[@migueltavares3815]

Hello. Whats the name of this model ?? Nice video👌

[@bostonstock3315]

I have a 2007 gsxr 600. Bought these same mirrors, bar ends and all.. I opened up my bar ends and they are just long screws, no brass parts, they just screw in. I can’t get the bar end to mount flush. Any ideas?

[@ClutchFirst]

Hit me up on IG and DM me some pics.

[@benlim3196]

The mirrors... they dont come in pairs? you have to get them individually?

[@kataloganz]

nice video! I have a question: what if I want to install the original bar end weights?

[@MotovationUSA]

Unfortunately theses mirrors can’t be mounted with the OEM bar-end weights.

[@Da.Onus.Burger.618]

GOOD, because the factory ones were made for people who don’t have shoulders! 😂😂😂🙌🏾

[@MotovationUSA]

Agreed! These really do help get your view outside the shoulders.

[@ClutchFirst]

In mine, it was all elbow when overtaking. Thank you for watching and welcome to the channel. Subscribe to help the channel grow.

[@alx116]

I got the rizoma bar end weights on my streetfighter.Can I install these bar mirrors with the rizoma on?

[@jaycasiller2888]

Can these fit Ducati Hypermotard RVE without removing the signal light handguards? Or what are my options. Thank you.

[@AlastairT00]

If you use a longer bolt could you replace the bar end weight?

[@aaa33849272tw]

One question plzzz, I have a Diavel 1260s. What adapter should I chose? Is it the uni one?

[@aaa33849272tw]

My bike is Diavel 1260 what adapter should I chose for motogadget?

[@pandababyrider5925]

Awesome video. Do these mirrors vibrate at speed? Thanks

[@ClutchFirst]

Around 140+ you’ll experience a bit of vibration. At that point, you won’t be looking behind you. They are really good mirrors and I’d recommend them.

[@pandababyrider5925]

Thanks a million! I’ll be getting them for the V2

[@ClutchFirst]

@@pandababyrider5925 link is in the bio. Thank you for the support and don’t forget to Subscribe.

[@AlastairT00]

What is the inside diameter of the mirror clamp? And the outside diameter of the bar end?

[@soldifalsi]

Two question for you bro: 1) can I put this mirrors on Rizoma bar end plugs? 2) which support do you use for GoPro?

[@ClutchFirst]

I’m using the GoPro Handlebar Pole Mount. It will run you about $30+. You can mount the mirrors on a bar end plug but it will have an unfinished look. Meaning, you can’t use the provided end caps. But, it’s definitely doable. Thank you for watching. Subscribe to help the channel grow. 🙂🙌🏽

[@JuuustYeet]

hello, question about these mirrors, would it be possible to install them along side lever protectors?

[@MotovationUSA]

Bar ends or lever protectors. One or the other, not both without some modification on your end.

[@gabkalderon]

can someone tell me if these are too small? is field of view ok? I'm not sure if go for the blades or the page version. I'm afraid the page will be too big

[@ClutchFirst]

Both are great option. Which bike do you own? I specially went with that style because it fits the StreetFighter lines. The field of view is irks perfect for me. MotovationUSA.com/cfny

[@gabkalderon]

@@ClutchFirst z900. ended up getting the pace. Wil larrive in a week or so. 🤘🏻 thanks for the reply

[@kikoy08]

I would rather have mirror that breaks than having this with a price tag 10x breakble bar end mirrors

[@jorgecalderon2233]

Do you have a chrome mirrors ?

[@redrockracing4571]

Where did you get that replacement screw on the OEM mirrors that were removed?

[@MotovationUSA]

You can check online for a pair. One is standard and the other counter.

[@shehkh]

@@MotovationUSA Mike do you know what they are called to be able to search online? Thanks…

[@liljonwithnoh]

Are you guys in Canada?

[@harleycharlie5330]

I feel like for the that money the hardware should be right

[@daniesloria1]

Hi ! Do you know if they are universal ? I have a HD Sportster S …..

[@MotovationUSA]

Take a look at the Rizoma Cut Edge mirrors. They are a universal mirror and come with adapters to install 3 different ways. Take a look at our video "Rizoma Cut Edge Mirrors - Unbox and Install." They are brand new from Rizoma.

[@gsxrunit]

Can these work on 2018 Bmw S1000rr?

[@S1knaked]

Do these fit on 2022 bmw s1000r?

[@DJKOSTAS1000]

Do this fit in on 2003 Kawasaki z1000 ?

[@yudho4874]

What kind of mirror do suitable for street fighter bro?

[@MotovationUSA]

You can actually fit the CRG and MotoGadget mirror less mirrors on the StreetFighter. We actually have a few videos on the channel showing both on. Also you can always install one of my favs, Rizoma Spy R. All links are in the description.

[@MotovationUSA]

You can actually fit the CRG and MotoGadget mirror less mirrors on the StreetFighter. We actually have a few videos on the channel showing both on. Also you can always install one of my favs, Rizoma Spy R. All links are in the description.

[@howards.stormesii9804]

Where did you get that shirt, I want to buy one!

[@ClutchFirst]

Yeah man, that shirt is one of my favorite. It’s Kyle Wyman’s pit crew shirt. You should be able to purchase one on his official site or hit him up on IG to grab one for yourself. Thank you for watching and welcome to the channel.

[@MotovationUSA]

More merch will be coming VERY soon, with the new livery. Keep an eye here www.shopmotooption.com/collections/all/kwr

[@m.sakthi8127]

Link

[@amazonledlights]

Hello, I am the manufacturer of LED headlights and like your video. I really want to have an cooperation with you. I have sent you the message via Instagram. Looking forward to your reply.

[@stephencarbajal5657]

The hand motioning needs to stop🤦‍♂️ great review otherwise way to animation