Motorized Bicycle NT Carburetor Cable Installation

Step By Step instructions on installing your throttle cable into your standard NT carb. It will also work for CNS and Speed carbs as well

[@skodziarz7503]

The most intense tutorial I've ever seen. Straight to the point and simple. Thank you.

[@ricks247]

I was almost there, missed the lining up of the slot on the plunger. You saved me ages of messing around. Thankyou

[@TightTautog]

very straight forward, and helpful, that is the kind of video I want to watch. Thank you!

[@Studyyou]

ये wire लगाने से क्या फायदा होता है

[@loganbeeman3854]

Never dealt with these style carbs before and have an old Mikuni that's just like this, rusty carb broke the cable trying to take it off need to replace so really helpful for me thanks a ton

[@yZEEHC1]

Finally a video that actually gives me the information I'm looking for.

[@ryankline5282]

Your video was so much help because we did not know that the pieces had to lineed up and your video was the one to help so thanks so much.

[@childofanovelty]

Thank you so very much. Would not have been able to assemble my first motor with out your help. :)

[@childofanovelty]

your channel just got subscribed

[@lecobra418]

Thank you, straight to the point, crystal clear, the kind of video I'd like to see more often.

[@Thesyndicate11111]

Golly, thank you so much! With the help of your video I was able to install my first carb.

[@fredmelendez4547]

you guys just saved me from more our of work on my 89 lt230 thanks so much

[@gerryballuta]

Now this is helpful

[@pollocksjones7789]

helpful and straight forward, cheers.

[@charlescurtis1042]

Thank you for posting

[@dasturm7504]

simple and straight to the point thanks a bunch

[@trackernichols]

Love the video! So simple! Thank you!

[@MyView-ui4uo]

Thank you for this video, you helped me figure out what i did wrong :D

[@ericmorgan2673]

No bs straight to the point

[@Sharker2468]

thank you! chinese instructions are notoriously hard to follow

[@mg-pm7mh]

yes very helpful Thank You!

[@saiesafari9640]

very helpful. thank you. have a good 2018

[@slimeyt5449]

once I've put it together, it won't allow the bike to go and just stays at a speed

[@brandonkramer764]

ROGHT

[@02afu]

PerFecT bro 👍

[@ismokecannabis602]

dude you fkn Rock...thanks

[@edwardsixx6344]

So question what do I do if there isn't a spring on the inside? How do I replace that spring?

[@victorsdirtbikes9790]

Very nice, thank you.

[@ulissestoralla198]

Very helpful

[@Yeastlord]

I’m new to motorcycle repair so bare with me, I bought two carbs ready to go for my build but can’t figure out how to remove the inside round slide with the needle so I can install the throttle cables

[@macmotorizedbike3834]

Nice ..Mikuni vid would be nice as well

[@jackrides1463]

Thank you, well made

[@InfinityIsM3]

Malfunctioning of this pin can cause high acceleration?? Uncontrollable??

[@jessihawkins410]

legend. thank you

[@naosabes2589]

Thanks bro

[@sodiqolamide7204]

Nice one 😁😁😁

[@Dr_KAP]

Does the pin sit in the slider really loosely? I have another tiny little clip thing it’s like a u shape? Not sure where it goes, on the inside of the black slider thing or on the outside where the pin sticks out!?

[@robertdaniels5755]

How do I get the cap to stay on the carburetor that holds the throttle cable it keeps popping off?

[@th3n3wn3wb5]

Is the pacman clip needed?

[@justinlawrence3668]

Yo thanks so much

[@Billy-Boggs]

My bike won’t fire up putting bbr tall bars on my pit bike and I had to put a new cable on it and she don’t wanna fire up sounds like it is not getting gas

[@JonahNAloha]

Ordered my carburetor last week, and it didn’t come with a Pac-Man clip. The needle came with a c clip. Could this be the reason why my idle runs high for a bit then drop down after I hit the throttle?

[@josephamato8234]

I installed perfectly ,but when I pull the throttle handle, it doesn't return back. The spring is correct. I even filed down some plastic inside the lever on the kill switch.??? Can someone help me???

[@kiran__jojo]

Thankyou

[@sctstone]

Can you tell me where I can find a throttle cable with the proper crimped end to fit into the round disc? I have found a lot on line but the crimped on barrel is sideways compared to what I need and what you have in the video. Replacing a broken cable.

[@MrMwmussel1]

I'm working on a OLD Honda c102 and I can't get the throttle cable unhooked from the carburetor. Should it just slide out once the cap is unscrewed, or is there a screw I'm overlooking the would be holding all of it in?

[@ytchronic_elote3884]

I did this to put a new throttle cable and when I turn on my quad and it revs up super high and I don’t know how to fix and yes I did get the right size can sum one help me out pls

[@BlownMoneyENT]

When I pull the throttle, I don’t accelerate and the motor doesn’t rev . What is the problem so I can fix it

[@Jp11130]

Cable won't go all the way inside 1 inch left outside What's problem ?

[@Danielmieczyslaw]

you very very good

[@_harleydavidson_iron8832]

very well 🌿🌿🌿🌿👌👌👌👌

[@subhashjainyoutuber8673]

👍👍

[@Johnjohn-eo6mb]

where can i buy high temperature red clutch friction pads

[@fortex7074]

Niceeelyyy

[@Cleanish_n54]

Where can I buy the Pacman clip and the needle I do t want to buy a new carb

[@peterfarineau7642]

so I need to know something if I'm leaking gas while the throttle is down that means I need to lower the pain right

[@toothytube]

Probably not, vacuum draws the gas into the carburetor as the needle (gas) and slide (air) are raised by the throttle cable. Gas entering the carburetor by gravity is usually indicative of of a stuck or defective float or float needle. That's how the "tickler" primer works, it temporarily lifts the float in a position that allows the float needle to slightly flood the carburetor with raw gas for initializing a cold start. Whereas the choke creates more vacuum to maintain a rich mixture for the duration of the warm-up period.

[@educationadda7764]

Jhakaas

[@prafulingle3661]

Bajaj Platina ki accelerator wire double kyu Hoti Hai kripya ek video Banaye

[@ivancornejo8619]

Where can I get the spring?

[@Martybrown-kc4xg]

wat size cable do i need for 125 pit bike

[@nikolasbenitez8088]

What the name of that throttle cable

[@noumanali576]

Agar wire Ka agay Kuch na hi to Kia lagaiye

[@5xgreentv33]

Mine would stay straight it goes to one side

[@coolmw2player]

where to get ur channel logo on shirt please

[@mahantheshmantu436]

I want TVs we go acceletre carboter pistin

[@jordon2loud806]

“KC fitted run bout 150”

[@SomalidocumentryTV]

Good 'but with Voice it would be More better

[@damianterrazas6249]

WHERE CAN I FIND THIS PACMAN CLIP

[@MarcusG40]

You ever find it?

[@jukeidricbagley9953]

Way to get right to it

[@dakdalj2523]

Please video carburator pz 30

[@jaxon7144]

I got swap the sprin

[@galaktikastukstantis9229]

Mine is stuck and I cant get it out

[@302diamondstate7]

Daumantas Mikalauskas ur slide is stuck so is mine it came apart about a week before I tried fixing it and now is almost like it's welded to the carb

[@galaktikastukstantis9229]

302 diamond state actualy it magicly fell out

[@Realitygetreal]

that end is easy other end on an ATV???

[@austinpenn1587]

I lost my pac man ring, can I go without it?

[@L3nzu]

no

[@stylesonwheelzllc]

were can i get a pack man clip

[@andyholden8554]

did you find the somewhere to buy the Pac man clips?

[@dorianfrancisco6562]

No but it still works good but most likely online I made mine if u have a little washer and some nail clippers it will work

[@dorianfrancisco6562]

Andy Holden I just looked online and couldn't find em online u might have to make one let me know if u have anymore questions

[@andyholden8554]

Thanks will have a go tonight.

[@damianterrazas6249]

I can’t find the PacMan clip

[@gurumayumkrishnamanisharma5066]

Tvs xl100 same video

[@JacKas-q7f]

Muzyczka do szału doprowadza

[@Hurtn4aSquirtn11]

Thanks mate great work...

[@kishorlangade4219]

Thanks

[@cutiegirlsbriannasisters4494]

Thanks bro

[@StandFast1611]

Thanks

[@bikramnaik9267]

Thanks