Motorola Moto G Screen Repair & Disassemble - Fixez.com

[@webdevelopertimofeimihhail3502]

You are lifesaver. Already order third screen with frame, because there was no dynamic. But it seems that it is easy to install. Thank you very much

[@pwillo1]

Great video - really clear instructions. Note to others - take great care when removing earpiece speaker (5:19 in video). I neglected to soften adhesive with heat gun before trying to remove speaker, as advised in the video, and damaged it. I had to buy a new replacement part which worked fine once installed. In answer to other queries, I installed the speaker with the raised, higher contacts aligned to top of phone.

[@Zalfrin]

I aligned my bumps to the bottom and speaker works fine that way too. Seems it doesn't matter. One thing I did do that wasn't in the video was to move the metal mesh that covers the earpiece from the old screen to the new. It's thin but maybe it helps the speaker maintain contact with the PCB. Also looks better with it in place IMO. :)

[@Pinkslee]

Thank you for this tutorial! At first the phone wasn't turning on, and I assumed I messed up. I plugged the phone in via microUSB and after about 30 seconds the screen lit up displaying 0% power; the battery was completely drained. After charging for 10 minutes the phone works great now! Thanks so much.

[@vinceadams1581]

My phone and screen worked fine, after replacing screen with one I ordered from Fixez. Color was good. Swiping was good. Resolution was good. A few things I think the video might should've noted: 1. Make sure you remove all 14 torx screws. Count them. They are small, dark and hard to see where they are hiding in place. I left one in an pried forever until I realized it. 2. The ear speaker piece came out in four pieces instead of one. It's the speaker, plus a piece of black mesh, plus a small frame, plus the wire mesh stuff that's visible. Might try heating it and pushing it from the front side to get the whole thing out to pop out the backside in one piece. Also, I'm not sure it's important but i suspect it is - note the orientation of it. 3. There was a small white flexible neoprene piece that went around some window. I just happened to notice the new piece didn't have it, so i had to remove it from the old assembly and insert in the new. The video didn't mention it. Also, there was a slender piece of foam rubber about 3/8" long in another place near the battery connector ribbon that was on the old piece but not the new. So I moved it and re-used it too. I would say compare the old assembly to the new assembly to spot any differences, and move any pieces as necessary. 4. I made do without a spudger. And I used a sharp knife instead of a pick. Lastly, I used a 10X lupe magnification in order to see the small stuff before I did anything, so I would know what I was working on. Thanks for the good video and quality parts. I feel like I can get another 4 years out of my moto G 1st generation.

[@potatosei2103]

How did you manage to disassemble the speaker?

[@faridwicaksono6387]

Sir, what is the name of that very little screws

[@owenmcdermott5592]

Very nice, clear complete step by step instructions. The way it should be done! Thank you again and keep doing it.

[@GoldFellaTim]

it makes me cringe that every time is see a video with the moto g, no one knows how to take the back cover off.

[@HypnoPantsOnline]

It's all about making it so complicated you'd rather buy a new phone than repair it.

[@Vanessinha91Pucca]

Complicated? I just pull from the USB slot no tools need

[@alex_frizzell]

you know you can remove the back cover without using any tool...just put you thumb on the M on the back and pull up with your other hand at the usb port.

[@Fixez]

+AlexFrizzellProductions Thank you for this information.

[@fael097]

+AlexFrizzellProductions you know this video is about selling useless tools, right?

[@Fixez]

The video is used as a reference point to assist anyone in repairing there own device if required. We also recommend tools required for the repair.

[@eduardom.e6717]

THANKS FOR THIS VIDEO! Yesterday i broke my phone screen and today, with this video, i was able to replace it. Again, THANKS!!

[@Fixez]

+Lachlan Keene You're welcome. Thank you for watching!

[@datom4002]

Fixez.com can i change only sensor ?

[@ChristianGibbons777]

Where are the Plastic opening tools on your website??? Also

[@ChristianGibbons777]

Also, is the Anti Static Wrist Strap meant to be a substitute for the Heat Gun basically???

[@joeynrg]

Hi thanks for a great video. I've got a working moto g again. Had the same issue with the earpiece not working but stuck some foam double sided fixing tape to lift it up against the connection on the board. You might want to just add that tip in the write up as I've noticed a few people with the same issue in the comments. Thanks again

[@Zalfrin]

Hardest part for me was finding the tiny volume and power buttons when I lost them on my carpet. :D Other than that, went very smoothly. Thanks for the video.

[@aca1790]

Fantastic Video. I understood every detail and you explained it so well step by step for all us amateurs that are going to be doing this for the first time. What place do you recommend to get a replacement screen from that doesn't cost an arm and a leg? Thanks again and keep making these great videos and also for saving me a lot of money on doing it myself instead of taking it to a repair shop that usually charge an arm and a leg.....

[@ChristianGibbons777]

New viewer BTW💗from Canada🇨🇦Awesome😎

[@brucemcisaac1241]

Really helpful - my clumsiness damaged the earpiece when removing it but everything else went fairly well - a very good guide. Thank you.

[@Fixez]

+Bruce McIsaac You're welcome, thank you for watching! Just an FYI, we offer the earpiece here www.fixez.com/motorola-moto-g-earpiece-speaker

[@LPFan33]

the music was way too loud / totally unnecessary

[@leeabrahams9889]

***** Agreed it really is too loud!

[@bbb-un9hq]

I thought it distracted from the content. But the tutorial seemed quite comprehensive.

[@juliosalcedo6737]

Xa Ia I agree

[@matchuclassic9887]

+Shrek Your name is way to over used and your comment is unnecessary. Win win

[@yairshimshoni2907]

Thanks for the video! It is very helpful. For the sake of your next videos, please consider removing the musical sound track, or significantly decrease its volume. It is definitely disturbing and makes it harder to follow the instructions. Thanks!

[@sxycrml01]

Awesome vid. Will be fixing my daughter's phone when I get off today.

[@Fixez]

+Frances Simmons Great, good luck.

[@hyperspacey]

Thanks for the videos, got my other half's broken phone working in no time.

[@diegosaroka3724]

Very useful video. I´ve just succesfully repaired my Moto G with spare screen/digitizer bought from Amazon. The video is very easy to follow. Thanks.

[@florenceamber1]

Thanks for the video. i used it to help me replace my cracked screen after purchasing a replacement screen and display assembly from you guys. Everything seems to be working well, except when i make calls, the person i call hears an echo. What do you think the problem is?

[@joshuastone7750]

Great video and site. Ordered from them and Screen looks and feels like original. The only problem was that they covered up the notification light window (which is between the front camera and the speaker) with adhesive.

[@Yadzay]

Hi mate, thanks for the vid. I was able to replace my screen, however, nothing comes up on the display, I can see that the backlight is working but I just get a gray/black screen. Any Ideas why this might be?

[@NotouriousNateBros1]

Hey what soloution or epoxy do you use or alternative would you suggest when re apply the screen......secondly would the phone continue to be water proof after?

[@DionTholen]

Very informative video *****, thanks! I was wondering if I only want to replace the battery, is it just as simple as order a new one, open the phone remove the old one, then align the new battery and close the phone up again? Is there no special tape or adhesive required?

[@walterwhite-tx3ei]

very nice video...explanation is easy and simple...thanks...

[@petrosbarmpounakis6139]

Guys great video i want to ask if this is still gorilla glass thanks in advance

[@carlosmunoz2541]

Hi, I just saw the video and I wonder if there is any chance to send a photo or a short video of my bike g to make sure if the screen really is broken, and if to be true buy the items for repair.

[@cranem258]

I bought a replacement part that comes with the LCD and Touchscreen combo, So in that matter, I don't need to disassemble it all, just exchange the frontal speaker in the old combo to the new one, right?

[@alexmeiser-stedman7851]

hi what sort of adhesive strip is that? standard double-sided tape cut to size? how long do you apply the hairdryer heat for? i'm anxious that too much heat will damage other parts. thanks

[@alexmeiser-stedman7851]

Thanks!

[@halinameza8265]

question! the motherboard connector in the 1st gen is the same as in the 2nd one? I just broke it and i will like to know if the old one could work

[@alessandrorusso4846]

I would like know if inside moto g there are warranty seals? Is there any seal that makes it clear if the cell has been disassembled?

[@maurycykaczmarek9998]

Awesome! Very good guide!

[@bukky5352]

hello,i got my moto g screen broken,though its working perfectly well,do i still need d lcd+touch screen or just the screen alone?also which one is digitilizer tough glass?can u pls explain.

[@lisaslifestyle]

Thank you for helping me to fix my phone. 😀👍

[@Fixez]

No problem! Glad everything worked out for your repair!! Thanks for watching!

[@unleashthedog]

Very good video! (Apart from music a bit too loud.) Question: I have to Moto G, one fell in the water a few months ago and then died. The second fell on gravel a couple days ago and glass shattered, but LCD is working perfectly, as well as touch digitizer. I am wondering if i take them apart up to the point i have motherboards detached and swap them. Screen on the one that fell in the water seems perfect, my gf said that it had some watermarks, but I connected it to the charger and screen looks perfect when it briefly turned on for charging. After a while it started flashing going from a blue screen to the icon of battery exausted - i think it's not charging at all. Now "wet" phone is not giving any sign of turning on.

[@bukky5352]

hello,i got my moto g screen broken,though its working perfectly well,do i still need d lcd+touch screen or just the screen alone?

[@EU_z_Auta]

Very good tutorial :) What is the song name?

[@Fixez]

+Kawur Mobile Thank you for watching.

[@darkmemories8201]

To which countries are you shipping the display? Is it possible to send it to Germany?

[@abhisek1da1rockstarr]

Hey! In my case, my phone's outer glass is just broken but the touch works fine and the display is good too. So If I get just the outer glass, Can I fix it without needing the LCD assembly?

[@ltmikepick]

Thank you! It was very helpful. I succsessfuly installed it on my GF Moto G. Big Thanks.

[@ComandanteJ]

I have a Moto G gen 2 (XT1068), is this guide still useful for that particular model?

[@imranino]

Got everything ready to fix it only to find it impossible to remove the screen with a T5 torx. Make sure you have a T4 handy as well, or else you'll need to abandon halfway though like I did!

[@sabaalkhatari7787]

thank you ^_^ you just make it easy

[@jaycartier]

On the website is there a way to see the Canadian prices? Or are the prices international prices or something?

[@Fixez]

+MLGKFC420 All Prices on the website are in USD.

[@Akshay-pc3yc]

hi there! which is the touch screen connector here? are the touch screen and display connectors separate? if not, can you please point out the touch screen connectors on the flex cable?

[@Fixez]

The digitizer connection is shown at 3:00.

[@Akshay-pc3yc]

Fixez.com Thanks! I found my XT1033 doesn't have such a connector for digitizer. :-( it has only that black wide ribbon connector.

[@zi-gaming4529]

Thank you.Very good.

[@Fixez]

Our pleasure!

[@YatharthRai]

Is it for the 1st Gen? What models do you support? And, are the replacement parts original?

[@YatharthRai]

and another question, does it come with a digitizer? Apparently, I have a leaking LCD.

[@Fixez]

+Yatharth Rai Yes, first Gen model shown on this video. You would get the LCD and Touch screen digitizer assembly through our site and this would be a high quality OEM compliant replacement screen. www.fixez.com/store/motorola/motorola-moto-g

[@amstanton1992]

Is it possible to replace the micro-sd card in this model? This is the one I have, and haven't been able to figure it out.

[@kamakasi_banned]

Here is a question. i did a screen replacement for a friend. No problem went smoothly. But when i put screen on using the 3m double sided tape i pressed it firmly and used heat and even used baby clips to squeeze it together. Even after all that and it cooled down the screen still started to seperate from the adhesive. Any ideas on why?

[@Gordonflash1977Tanner]

Great guide, the only difference was mine needed the t4 torx not the t5..

[@ericfithian8208]

Thank you!! got as far as beginning to remove the multi connector, then thought... yeaahh,, probably should get some help. video much appreciated!

[@podye1]

Can you guys please make a video repair for cracked f3 optimus screen I bought one for 16.99 free shipping on Amazon and nervous to do it without a tutorial also after u use the heat gun do you have to use it to reheat the adhesive from the new screen or just screw everything back together? If so can you guys upload asap I'd appreciate it if u guys can

[@Calomi]

HI!. If u can help me... I read in the comments that isn't possible or is hard to separate only the glass from the lcd (if only the lcd is broken), so why I see people selling only the gorllia glass on the market?, I have to overlap this with the other glass? or is it a scam? what do u think/know about it? Nice video! :D

[@Fixez]

+Camilo Berríos The LCD is fused to the front glass panel. We do not recommend replacing only the glass nor LCD. Specifically on this model, it's simply not worth the repair process. You can purchase the LCD and Touch screen assembly for roughly $29.99 please review this here www.fixez.com/store/motorola/motorola-moto-g

[@humbertohernandez1738]

I'm going to replace my moto g screen right now, I got the screen and everyting but I don't have those strips. do I really need that? and if I do, where can I get it? I hope your soon response since I'm about to repair it

[@MerlinandJesusrock]

Thank you, this has literally made me so happy :))))))

[@SuhasRW]

Hi *****, I have a Moto G (2013) which has a hairline crack on the screen which is barely visible. The phone works perfect but the crack bothers me so I thought I'll fix it. Since there's no damage to the touchscreen/digitizer I can replace the front glass only right? I'm confused on this touchscreen/digitizer/LCD setup. So please explain what method I should use. Thanks!

[@CandleMcMurphy]

Excellent tutorial thanks.

[@vanessabayer11]

I tried using the t5 screwdriver but it didn't fit into the screws (too large). Is it t4 torx screwdriver?

[@PeteBurden]

Thank you very much. Nice video. XT1039 (White). Of course, I ordered a black replacement screen, not a white one, not realising which bits were white. But my son doesn't seem to mind the new look. On mine there was a small yellow bit of plastic underneath the blue protective screen, over the smaller connector to the screen. I had to open this up in order to flip the ribbon cable connector. But nit sure why I did this anyway as the new screen replaced that part. Getting the speaker the right way up was tricky. I didn't look to see which was it was before it came out - it fell off the broken screen. I noticed in the comments that it may not matter. I put the sticky up bits towards the top of the phone, and it works. Also I was left with a slight bulge where the ribbon cable came in - meaning I couldn't quite clip the mid body on properly. But doesn't seem to affect the phone, and is covered up by the outer shell. I probably didn't seat the ribbon cable properly somehow as it came through the hole. But all those Torx screws - I couldn't be bothered to open it all up again. BTW I also agree I am not sure they are T5 (could be T4?) but T5 seemed to work.

[@kennethlee8566]

do you know where I can buy a moto g screen my screen is completely cracked

[@saturn16]

Hi Fixez.com, I'm just about to replace the screen of a friends phone, he has the Moto G. I've done a few Samsungs, but had the frame Digitizer and screen for those replacements. I'm going to have to remove the old screen from the frame this time. How hot do I need to go to remove the screen?, I have a lazer temp gun. :-)

[@saturn16]

***** I have changed the screen and digitizer. When I turn the phone on the screen only glows. It is getting power but does not display anything. I can call the phone and it rings and vibrates. What have I done wrong do you think?

[@saturn16]

Just to add. The LCD connector is clean, I was very careful not to touch it.

[@akshaytanwar667]

Can u tell me cost of replacing sim slot in moto g 2nd gen.

[@Inferryu]

Hi, I have a MotoG xt1032, I need a specific screen or is compatible with all the models? Also, do you ship to Mexico?

[@Inferryu]

+Inferry Forget the shipping question, I just found the answer on your site, I'm still unclear on the screen thou.

[@Inferryu]

+Inferry I see the screen with the housing is on sale in the site, assuming it comes assembled already, will I need any adhesive strip for something else?

[@Fixez]

+Inferry We offer worldwide shipping, once at checkout you will see the options available with pricing. We have this assembly that would be compatible www.fixez.com/store/motorola/motorola-moto-g/motorola-moto-g-display-assembly-and-frame This model with the frame would not require any adhesive. We will however include a strip of adhesive and a free pry tool with your purchase as a courtesy. Please contact us if you have any other questions. Thank you

[@notmyyoutube84]

hello .i have the gsm one. is the display compatible with the cdma one? because I can buy a new cdma moto g with 50$ ,and replace my ugly looking one :)

[@naumansm3]

Hi, I recently replaced my screen+digitizer in my moto g phone. Both the display and the digitizer worked well (although the red was slightly less 'red'). There was a small area near the top where the touch screen sometimes worked, sometimes didn't. I removed and re-inserted the ribbon cable for the screen and then the digitizer stopped working. When I repeated it, the screen also stopped working, though the LED backlight worked. Thinking I broke the ribbon cable, I ordered a new one from another vendor. This new screen also doesn't work at all (only LED works). But the touch screen works fine. I did an ADB screen grab using the USB to computer and I can 'see' what the phone screen background image is being trasnmitted to the screen, but I don't know if the circuit is damaged or this screen is bad too. Any ideas would be greatly appreciated. Thanks, Nooman

[@NublixMc]

How long is the adhesive meant to set?

[@Fixez]

+Nublix // Gaming It varies, should not be to long though. Use your heat source and apply slight pressure so it adheres better. Possibly 5-10 minutes should be sufficient.

[@ADQAutomotive]

Does the glass separate from the digitizer?

[@Trev11444]

If I have two of these phones, one with a broken screen that is currently on a plan and the other with internal issues, can I take the entire display assembly from the bad phone and swap it out the the phone on the plan and without having to visit my provider or anything? Will the "in use" phone recognize that anything has even occurred?

[@Fixez]

You should be able to swap out the motherboards without any problem.

[@Trev11444]

Awesome. Thank you!

[@metalron84]

At the Display assemply connections, i ripped the chip like bit that was attached to the flex cable and the motherboard, does that mean the end of the screen?

[@metalron84]

***** drive.google.com/file/d/0B63dHydZ3tsEV25ybjVFb0NTbzZIUTRuQ21pYkI5LVBadTJn/view?usp=sharing here' a link of its state, is there a possibility to use the glass? I needed it for another phone :/

[@PersistantPigeon]

hi at around 8:03 i cant seem to keep it down and have it all connected how do i do this???? help 111

[@Fixez]

+redmcq The ribbon cable should have a small amount of adhesive on it. If the new part doesn't feel free at add a little.

[@Maya-qy1nu]

Hello, is it easy for a not expert to change the display? Do i have to buy the tools or not? Sorry my Bad englisch: p

[@Maya-qy1nu]

***** yes i had visit your Website. So what would you recommend: to buy a new Smartphone or to repair it?

[@chavapasanchez1525]

you can get the tools for cheap on amazone there tools are expensive including the screen,i bought my screen and my tools on amazone cheaper and fixed my phone

[@fredericocolon224]

how is it replacing the 1st generations Moto G with the expandable memory?

[@xjem1754]

I've ordered my new screen already from Amazon. Do I need the antihesive to reasemble the phone.

[@T0KY0MARUI]

Hey do you end up fixing the screen ? Do u still remember the price u paid for the screen ? Thanks

[@joesagay9541]

There s a horizondel blue lines in the screen can it b fixed without replacing

[@sammorris1459]

Hi, it seems that most replacement screen assemblies don't include any kind of metal speaker grille and the existing one can't be removed from my broken screen (can it?). I noticed that upon replacing the screen the speaker is no longer securely fitted and rattles / vibrates badly - do you know how to remedy this? Thanks

[@sammorris1459]

Thanks for the reply. Is there any way you could get one of these to the UK?

[@waeldeleandreas]

Awesome Video super detailed perfect !!!

[@pereirarfc]

I just assembled my screen with frame, but after the assembly there was no backlight in the screen i can see that is working but is almost impossible to see anything, i reassembled the old screen and there is backlight, i think it is a screen problem but can you please give me an opinion about this? Did i do anything wrong?

[@borstarcic2197]

Hi, can you help me. I replaced the screen as instruced, but the touch doesn"t work!! What should i do?

[@borstarcic2197]

***** I did but the touch still doesnt work. I"m using voice control and a mouse now.

[@pari7663]

Do it also change the touch of the phone

[@GianlucaBruno01]

hi, does the display for xt1032 and xt1039 (4g) are the same?

[@Fixez]

+Gianluca Bruno Yes, they would be cross compatible.

[@dipi71]

First, you should make sure the phone's Android OS is shut down and the phone is completely switched off. Second, if you'd read the Moto G manual, you'd know you don't need tools in order to remove the back cover. Third, you don't bend the battery connector as you do at 2:32; even if you went on to dispose of the battery, it is bad practice.

[@evelynricahrds2461]

Lacks a few subtleties, like pointing out if you don't get completely under the ear speaker that you may accidentally rip it apart.

[@lidiacovella7318]

i broke the lcd but not the glass, do i have to replace the complete display assembly?

[@sashamarinichev]

I think the chances of damaging the screen when replacing the frame alone are quite high, right? Seems that they're glued solidly to each other. Help me to decide=)

[@Fixez]

+Саша Мариничев Yes. That is correct. Are you looking to just replace the frame?

[@sashamarinichev]

+Fixez.com yep, it has some nasty scratches

[@silviuguseila2552]

Hi, can you please advise, my phone started making high pitch noise, then no sound. Restarting sometimes made it work for a few minutes. Could it be the speaker? Seems to be very related to software as well as when the sound is not working, no video can be played, as if the drivers are missing. I cannot film a movie either. Does this makes sense to anyone? Thanks!

[@picko19]

Amazing thanks! My phone is like new again! 100% recommend this video. Cheers Fixez.con

[@Fixez]

+picko19 You're welcome. Thank you for watching!

[@hoyle600]

Can you help me with my Nexus 7 2013 edition I think I need to replace my logic board I just replaced the screen

[@dazaro3]

Thanks,good video.

[@duonghaxuyen]

I assembled the phone and realized I forgot the protective plate for the LED. My phone works well now. Should I tear things apart and insert this guy back in or just leave him? Thanks

[@TheIcekake]

Is it alright if i just glue them back together without an adhesive tape?

[@MijailAgipUriarte]

***** you removed the tape form the framework, then from the sides of the LDC display, then you didn't put it back on the video. So? Am i missing something?

[@carwynball4269]

Thanks for that. Really helpful.

[@harishkrishnan7540]

I am from India, does this site deliver to india?

[@SYEDIHTISHAMULHAQ]

does it have a JTAG port

[@nurseduckett]

the bits it tells you about are fine but the bits missed out are annoying: I bought screen attached to plastic frame you will have to transfer the speaker, cloth cover and grill and these are glued together and onto the screen! Don't forget the small foam grommet between the glass and front camera and the mic cover at the bottom - green plastic thing. otherwise all good

[@macchiatogurl91]

what I want replacent with is the side borders not the screen,where the bezel is..can you replace that part..I wanna make me phone look its new,coz my bezel has a lot of cracks on it...is that possible?...

[@devdattn1168]

+lea rodriguez You have to buy the frame of the screen

[@johndrippergaming]

when I connect the charger only the notification light turns on with or without battery what could be the problem? power button does nothing, cannot access fastboot or recovery menu either :/

[@northernirishgamer6534]

Does this work with Moto e?

[@Fixez]

+ Vincent Felix We apologize for the inconvenience. Reach out to our support team. [e-mail] We'll make this right for you.

[@patrickkelly6350]

Hi there i put the new screen on and it now flashes every 6 to 7 seconds. Can you suggest something please. Thanks pat

[@Fixez]

+Patrick Kelly Is the device powering on and powering off?

[@DevinJuularValentine]

Hello, I have followed the steps and the screen works - but the touch capacity is not working. What could I have done wrong? I have re-checked the connections. Any idea?