Step-by-step on how to mount a scope to a CVA Cascade using a Wheeler Engineering FAT Wrench and leveling system.
Пікірлер: 26
@keithcox3350 Жыл бұрын
Great camera work on this video! Your instructions are simple but you don't miss a step...everything covered. Thanks!
@kirkoutdoors8806 Жыл бұрын
Thank you!
@codyevans8769 Жыл бұрын
Can’t wait to see how that thing performs this turkey season!
@MOLLYLAB20117 ай бұрын
Well done. Thank you.
@rodog504 Жыл бұрын
Was looking at this but not a fan of proprietary magazines. Noticed they were out of stock on their website when doing research. Weatherby or a cva/Bergara are what I'm looking to get though.
@limajuliett3406 Жыл бұрын
Happy with the talley rings?
@kirkoutdoors8806 Жыл бұрын
So far, they have been great!
@triph4 Жыл бұрын
Did you get medium or high rings?
@kirkoutdoors8806 Жыл бұрын
High
@jrod78684 ай бұрын
Are these rings the "extended" model or regular?
@kirkoutdoors88064 ай бұрын
Regular
@mattc51859 ай бұрын
What Talley rings did you use?
@kirkoutdoors88069 ай бұрын
High with a 50mm scope
@brianrichards56947 ай бұрын
Egw has one
@RepublicofTX Жыл бұрын
I’ve never used levels or a torques wrench. I eyeball the shit and go with it, just go by feel on the screws too (I do use Loctite though). Never had an issue and all my reticules are straight 🤙
@brookesross463711 ай бұрын
Lots of warrior buying these rifles.
@Oregon-airguns7 ай бұрын
I’m to the point that i just won’t buy a gun unless it has a picatiny rail
@coyoteodie4458Ай бұрын
EGW has a solution for almost every rifle. And great customer service.
@ronl384 Жыл бұрын
That did not look like 20in/lbs torque.
@kirkoutdoors8806 Жыл бұрын
How much do you think it was?
@kirkoutdoors8806 Жыл бұрын
The top of the red mark indicates the torque value. Were you looking at the top of the white?
@ronl384 Жыл бұрын
@@kirkoutdoors8806 At the 40 second mark-it looks to be set about 15-18in/lbs
@APACHE529CREWCHIEF Жыл бұрын
You’re bubble wasn’t fully centered
@kirkoutdoors8806 Жыл бұрын
Listen to the audio 2:14-2:25. The right edge of the bubble touches the right line each time I use a level on the receiver and the scope. This makes the scope level relative to the receiver. Touching it to the line eliminates the dead space you would have on either side of the bubble if it were centered, making the measurements more precise.
@averystoller2419 Жыл бұрын
Oh the people of KZbin 😂
@brookesross463711 ай бұрын
@@kirkoutdoors8806 Man this @apache529crewchief is a freaking warrior when it comes to recoil and bubbles. I have a very similar setup. Differences being that I used Talley style Leupold base/rings, Same scope on top of CVA's 7mm rem mag. I love it. I love the idea of using the line as a reference for the bubble to get it as accurate as possible. There are few places on this rifle that are flat. Therefor making it very difficult to see the bubble at times. Thanks for the tip. Great video.