23000 RPM - Reuse 24V Super High Speed DC Motor from DEAD Printer - Brushless BLDC Motors

[@MrElectron]

BEST BATTERY CHARGER DIY VIDEO - kzbin.info/www/bejne/kH-WpJR_gceMi9ksi=9_nLu0vKOqfn4zi_ *Join this channel to get access to perks:* kzbin.info/door/WFbPzBb7dCyCWuBA-DBrMAjoin *Mr.Electron Patreon's Page* - www.patreon.com/mrelectron *Hindi Channel* - www.youtube.com/@Mr.ElectronHindi *Alternator Channel* - www.youtube.com/@mrelectron_alternator *Watsapp Channel* - whatsapp.com/channel/0029VaQmmRaFCCoWOf7huh3G *BUY Brushless Motor Controller* : bit.ly/2UV9Ybb

[@nathanjackson2072]

I need this brushless motor speed controller, but the link won't work

[@narendrakumardhaneliyanare4718]

Good luck

[@deathincarnatesplace]

i want one that plug into american wall socket for garage fun.please email if you find.

[@AidenPearce806]

Mr Electron what is thr third wire used for

[@mrbojinkles22]

Never click a bitly.

[@icraftcrafts8685]

Hey man. great project. When you took off the magnet section, there were drill holes for balancing on the outside. if you put them in the same place they were, the vibration will be gone/much less.

[@DesertSessions93]

Must have been one heck of a printer!

[@markoscoli]

Parafusando o estator errado 6:34. Os fios deve ficar por baixo entre o estator e a placa de fixação.

[@free4logix]

7:42 reminds me one of ElectroBoom's video.

[@AidenPearce806]

free4logix yay another person who watches him

[@ray-charc3131]

Usually, this motor stayed in the original circuit board is less powerful than d.c brushed motor. Did it become powerful one after using your circuit board? I think you need to change to muti-strong magnetic pieces instead keep on using the original ring magnet!

[@sosscs]

What is that circuit you connected to the motor at 7:31 ? Is it a potentiometer circuit to control the voltage?

[@ErCanEverything]

Nice work👍👍👍🙂🤝

[@Proektirovshik]

Лайк, подписка! 5 копеек вставлю. Замени флюс на твердую светлую канифоль. На лужение трех проводов обычно уходит 3 секунды. Провода зачищай перевернув на 180 градусов губы кусачек. Тогда они не соскальзывают, а снимают изоляцию.

[@domingodeejayable]

lol man you got it all figured out I respect that but you got to mount that motor(big or small) properly before testing the max rpm it can pull off

[@hardnachopuppy]

Can you make a video about changing the weak magnetic strip inside the motor to strong neodymium magnets

[@siggyretburns7523]

I tried by just guessing the quantity, distance apart, and polarity. I resoldered the coils for the "Y" format. It was a no go. I know the ESC worked too. I ran a magnet on the original magnet to find the number of magnets and polarity, but that may be the problem in the first place. Reconfiguring the coils means the magnetics probably need to be reconfigured as well.

[@norbertk.1473]

Die Musik im Hintergrund bei Minute 4:53 : Ist das die 5. Symphonie von Ludwig van Beethoven? Und gespielt von Chicago Symphonieorchester?

[@MrElectron]

Sorry, i never really checked. I just liked , so i used it in my video.

[@ПрофессоркислыхщейДуплейНикола]

Уважуха автору видео не имея элементарных наборов отвёртки инструментов снять видео и набрать 2 млн просмотров это круто

[@NoName-og2nb]

на 3млн просмотров всего 17тыс лайков? представляю, сколько там дизлайков...

[@csn_-7662]

5:00 that how you don't do it. It's called cold solder. And what kind of printer works on 24v and needs to rev up to 23k rpm lol

[@roberthalbrooks9669]

Now... What are you going to use it for? Give a purpose or use for your findings! Neat video!

[@Aina1054.]

for fun

[@DR_dicasereparos]

Brother, What is this board that you connect the motor wires to?... thanks

[@wilfridkolarik7174]

Good realising for motor and good satisfaction ideas. Class

[@MuhammadYaseen-vx5hw]

so nice power of a BLDC motor...

[@surajkumar-pg2nc]

nice video, can you please tell the back ground score

[@AlexAlex-ex5bc]

Паяльщик из тебя ещё тот!! Учись паять, не боися погреть место пайки, припой должен сам растечься, не надо припоем замазывать...

[@alro4505]

Он не электрик, он диайвайщик. А это совсем другое. Посмотрите какие у него бокорезы ржавые.

[@AlexAlex-ex5bc]

@@alro4505 ✋Тем более! Диайвайщик должен быть универсалом- все должен уметь! 😂😉

[@youssefamer5264]

السلام عليكم ممكن استفسار الدائره التي تعمل علي تشغيل الماتور ما كيفية صناعتها ارجر الرد

[@KJ7JHN]

What model of printer did this come from?

[@johnviernesministries300]

what kind of ESCa did you used for that kind of motor sir?

[@5starcrafts97]

How much thrust can it generate ??

[@joseluissanchezmedina4207]

Ese variador de frecuencia que tienes te ayuda mucho

[@kavtech_midi]

ist torsion strong enougth to used as spindle cnc?

[@mouldykev]

Can you show us this one generating power as an alternator. Kev

[@naimi3059]

My brother, where did you get the engine?good job

[@sarag]

How much load this can picks ??? Means we can use it in drone ?

[@MrElectron]

sure you can !!!

[@sarag]

@@MrElectron thanks

[@LoganT547]

That would be an extremely powerful drone 😂

[@philippepastor3703]

Very good for a mini metal lathe 👍

[@manikraitong7481]

Can we make this as a generator for mini hydro power generation

[@mrelectron_alternator]

Hello

[@safiyassuleiman1988]

Nice video good work, pls can you make a simple ESC driver using MOSFET, thanks alot

[@GeorgeZaharia]

don't know about you, but i like the music finally someone that knows how to properly balance sounds.

[@siggyretburns7523]

It sounds like graduation music for nerds. 😂

[@electronic7979]

Very good video 👍

[@MrUmbraya]

You're a genius man. Thanks so much for doing this!

[@lachlanbird9688]

Thank you for the video.

[@gary00832]

How much torque does that little thing have, prob not much peanut butter would slow it down

[@teetat1]

you are newbie of soldering technic....but..you are still inventor..i.pround of you.

[@zbigniewteterycz1571]

Super projekt. Pozdrawiam serdecznie.

[@shinsystems2415]

Es curioso cuando en ciertos momentos la alta velocidad de giro del motor, la imagen ondula por el efecto del campo magnetico giratorio a poca distancia de la camara

[@q8hussain168]

It is a direct drive motor ?

[@كثيرالطيب]

Great but the most important thing is the safety precaution . From Kuwait🇰🇼

[@AndyTorrealba]

No especificas sobre el circuito que usas para la conexión del motor...

[@RFADICTOS]

excelente proyecto amigo te doy un 10!!!

[@thomytube1826]

Disculpa te consulto. Ese motor de que aparato se puede conseguir? En el caso que lo sepas. Muchas gracias.

[@xafael]

@@thomytube1826 motor de CC de súper alta velocidad de 24 V de la impresora DEAD - Motores BLDC sin escobillas

[@tusharg2751]

Can I use this to generate cycle electricity?? You had made video for it

[@khushprakashofficial3385]

How to make controller for 12v 5amp 16000rpm DC moter

[@apexaero]

Remote control airplane ESC (electronic speed controller) easy and cheap from hobby king

[@truelove3228]

By mozfet z44

[@noelmelo3460]

IN THAT KIND OF ESC WAHT IS THE MAXIMUM POWER INPUT ? PLEASE REPLY THANKS

[@AidenPearce806]

NOEL MELO thanks

[@siggyretburns7523]

I think he misunderstood the question. 😂

[@FearlessFly-j7s]

Dude take a bldc motor and directly connect the wires to both motors to geather color for color,connect drill to shaft and turn drill on slowly while giving slight spin on the other motor and it will run the motor with slot of power

[@Burn377]

6:30 you mount the stator upside down 😆

[@MrElectron]

🙄 yeah right 😄

[@MuhammadYaseen-vx5hw]

I have three same BLDC motors in my lab. your video good usually.

[@yaminoshinn1473]

In which printer can I find such motor ?

[@MuhammadYaseen-vx5hw]

@@yaminoshinn1473 I just purchased it from electronics scrap stalls which is open only weekly friday in my city.

[@alfama9022]

what is that pcb you connected the motor to at the time you powered it.

[@paullee5573]

Quite obviously it is a psu

[@gyaneshwarsinngh7974]

Pl explain connection and amp requirements

[@هاشمالشرقاوي-ل3ع]

بعد. ازنك. اسم التور. ايه. ومنين. اشتريه

[@settingshadow]

practice on your soldering skills you need to improve it

[@3mpiano429]

Can you please show the connections and working of CD drive BLDC brushless motor....

[@riloariichoariicho884]

What do you use to drive that motor?

[@mrelectron_alternator]

No hall sensor type bldc motor controller.. Link to buy it is in the description

[@riloariichoariicho884]

Thank 🙏💕 you you sir

[@machineshop2029]

@@mrelectron_alternator You can use the control circuit on the motor. No need to buy ESC. If you have enough knowledge to connect 24v, 5v, clk (pwm) wires

[@jaypeeflores]

can that motor also generate power mr. electron?

[@nitrousman8882]

Any more information about type of printer to get this motor? Thanks doug

[@VinodKumar-cu8ky]

I like video thumbnail. It's attractive.👌

[@ايادوردهبولص]

محرك خطوي مع مشغل. مع فاليوم سرعة. معه مقياس أر بي ام. (مقياس عدد الدوران)

[@joeprice3164]

Why don't you get one of those gas Grill lighters to shrink those shrink wrap tubes.

[@AlternatifKreatif]

menginspirasi, boleh tahu itu bekas printer apa ?

[@ClericChris]

Hopefully you can find a BLDC to make a drill that has more than 2 Modes: Mode-1. Attempt to twist arm off while launching work into low Earth orbit and Mode- 2. Paper weight.

[@rafiksk317]

How can I get the motor, give details about printer. Thank you

[@MrElectron]

Xerox very old machines

[@mvmcali6900]

Mr electron needs a soldering lesson

[@intentionfocus9206]

I thought the same. A total SLAG JOB!

[@hmoudkhresheh1979]

What type of driver you used to operate the motor

[@andrewferg8737]

Great video!!

[@faryantimaesyarohdjafar4574]

The energy is AC or DC?

[@josuealves2690]

Faryanti Maesyaroh. Dc

[@josemoreno3611]

You don't read the title of the video.

[@jaakkolehto1487]

While the name is DC, BLDC motors are in fact just 3-phase AC motors and the driver just has three half bridges to drive it with 3-phase AC. But of course the driver requires DC.

[@AppsquesiPagan-vg7tf]

where did you get the engine

[@gafurjabborov9524]

Спасибо большое за видео

[@matriXigma]

What would be its toque?

[@sertyfox2425]

6:36 Откручивать маленькие винты дрелью это что-то новенькое)

[@ИгорьЧетвёртый]

А то не видно, что это кто-то из наших?)) Ещё складная отвертка...

[@АлексейАвдовченко]

Нет, паять не умеет! Рукажоп!

[@ИванСтарый-ч1н]

Не судите его строго! Он из начинающих рукожопов!!! Как корабль назовёшь, так он и поплывёт!

[@thebrokeway9838]

is it at all possible to bypass the SC?

[@salemsaleem7368]

What is the kind of the printers , you take these motors from ?

[@babumohan4549]

this motor is taken from laser printer like hp 1020,1018 or Canon 2900 models. love from salem, India. ❤

[@TheKtariq62]

How can get drivers cercut from please tell me how get it,?

[@mickcarson8504]

You've got a good camera there, bro. It doesn't run out of focus. What camera is it? Where did you get those printer motors from? Care to tell? I am interested in this project.

[@templeviewgate]

Any junk electronic scrap buyers will have big stock of dead printers and other office automation electronic products ...just visit and for cheap rate you can source such motors, switches, relays whatever. In India there are so many service centers of computer peripherals..in every city we get whatever junk working parts and can be used for any project. In your country well there will be such electronic waste buyers or those who collect and deal.

[@rksingh7857]

Good, speed controller circuit Kong sa use kar Liya pata nhi chala

[@tomasalexisacostapena3149]

How I get a big one brussles motor tks

[@fadzilk4758]

did you run the motor on 24V to get 23000rpm?

[@MrElectron]

32 V

[@fadzilk4758]

@@MrElectron but how come 32V can produce 23000rpm? did you change the frequency of the supply voltage?. how?

[@AdityaSingh-108]

Could you explain which printer mortar is this

[@MrElectron]

Large printer machines very old type ...

[@riloariichoariicho884]

From where do you get so much of motor?

[@MrElectron]

Hobby.. Years of collection

[@spillmawthoh330]

@@MrElectron ll. Dominic j@ full

[@zees9669]

Very Good. Now can you run this three phase brushless motor without ESC? BTW Good choice of background music.

[@zees9669]

@@RituSharma-wy4wm Sister I already knew. The question was a joke in itself. 😁

[@daviddavids2884]

@@zees9669 girly, yer joke was not funny. it merely resembled one more, moronic question. if you want to tell a joke, go down to the pub. in many cases, written sarcasm just looks like stoopidity.

[@Drastisolution]

Which printer are you use this motor

[@joseluismontoya4367]

Where did you get that engine?

[@MrElectron]

Xerox

[@aiooongladyfrines4935]

No hall sensor I see it, your output driver is 3phase right? Square wave or sine wave?

[@machineshop2029]

All motor of printer and copier have hall sensor. and pcb on motor is its driver circuit. we just need to supply 24v 5v and signal pwm to the CLK pin and it will work. No need to buy ESC. because its driver circuit is very good. use sanken sla6024 power ic and lb18xx driver ic

[@shantilalbairwa9986]

Bhai yah 24v ki moter aapne kha se Li Aap agle video jarur batana

[@s.m.i.e3283]

How to get this type of variable circuit

[@ibrahimansari9111]

Yah motor kis mein se nikalta hai

[@stephenc2738]

Soldering is sloppy and applying the soldering iron to the coil without heat insulation can potentially burn off insulating enamel on coil wire.

[@andrewCNC905]

oh shut up . Always one to point out the obvious

[@sjoer]

Nice, these motors aren't even that expensive to get!

[@jolt9771]

Nice project 👌👌👌

[@lxw5231]

handle it safely, when you connect to 120V.

[@Lucas_sGarage]

It wasn't 120, it was 30V dc

[@jayanntv4964]

Where can I find that kind of motor?

[@sidamarali3030]

Where can one find such a motor

[@terrorshorts9768]

10:28 saved crash landing😁🤣

[@lionelroger626]

Bonjour, tu récupéres ce genre de moteur sur quoi ????? Merci

[@dickiehoppenstedt100]

Good project, but you have possibly have to do a training in soldering..

[@ginaldorui9245]

Qual o inversor que vc uso e caseiro posso adquirir o esquema Tenho vários destes motores mas não funcionam com as Esc norma para aero modelos que são trifasisas também Tem como eu poder adquirir este drive

[@zeitgeisterbrasil2715]

Ele não tá usando inversor man, não viu que a tomada fêmea deu 30 volts no multímetro?? Então não é corrente AC. A tomada com certeza tá ligada em bateria.

[@josuealves2690]

Ginaldo Rui ele deixou o link na descrição do vídeo vc encontra esse drive no banggood

[@arifchannel9593]

guys, for the alternator speed dc device that car needs, which volume is it?

[@Z-Ack]

Eleven, it goes to eleven.. thats one more than max, next level man..

[@Lucas_sGarage]

Just Buy a 50A esc And a servo tester

[@mmzhr]

Keep up good work :)