AC to DC for Welding Machine Output Voltage (Under 10$)

#weldingmachine #ACtoDC #arcwelder
Hello...
In this video, as I promised to many of my viewers, I tried to show how to convert the output voltage from AC to DC in an affordable way for the Arc Welding Machine I made before. Of course, the process I did is not only valid for this machine. You can convert the output voltage of your welding machine with AC output to DC with this method. The materials I use are quite affordable. Total price under $10. For the rectification process, I used 5 bridge diodes of 50 Ampere KPBC5010. By connecting the bridge diodes in parallel, I have increased the current resistance to 250 Amps. You can use 5 bridge diodes in the same way for your 200 Amp welding machines. For higher current welders, the number of diodes needs to be increased. I connected a 4700 microfarad capacitor to the output. In this way, the AC output voltage from 40V has increased to 60 Volts. Of course this voltage will drop during welding, but for the first start of the arc it is better to have a higher voltage.
We can weld materials such as stainless steel by converting our output voltage to DC. In addition, the weld seam is smoother. Besides, you can use your welding machine as a TIG welding machine. Of course, there will be other materials needed for this as well. Maybe we can try that in the future.
I hope you enjoyed my video and my procedures were clear. If there are places that are not understood, you can ask by writing in the comment section of the video.
You can click on the link below for my Welding Machine making video.
Please don't forget to SUBSCRIBE to my channel, press the LIKE button and activate the RING notifications to be notified of my future videos.
Our Welding Machine Construction Video:
• DIY Welding Machine / ...
Multimeter I use:
kaiweets.com/products/kaiweet...

[@pambinbjozon7505]

Hi!, I thank you all. Sharing your wisdom,for seeking knowledge to us all. Lots of humans can't afford wisdom. Too EXPENSIVE, EXSHAUSTING TO COMMUTE, but they had dreams to live in this unfair, abusive profiteering authorities that blocking progression.(greeders). I hope Education is FREE to COLLEGES to all COUNTRIES.

Thank you for your interest. However, I must admit that I found your comment interesting.

[@simonlinser8286]

AMEN brother.

[@samirhoubi5914]

​@حب

@@samirhoubi5914 شكرا 👍

[@mehmetcanhorzumlu7077]

Hiç işimize yaramadı yapılan emeyemi yanem yapmışoldugumuz parayamı hiç işimize yaramadı

[@Historynerd42]

Absolutely spectacular! I've watched a lot of welder builds and this one is fantastic! I'm building one now as I type this. Thank you. It's perfect.

I thank you too. I am so glad you liked it. Do not forget to use silicon insulated cable on the secondary side. If you have any questions, you can write here.

[@huseyinunlu8916]

@ sen bu trafolari sarmak icin hangi kabloyu kullandin benim kullandigim kablolar isinip eriyyor sonra dumanlar cikiyo bi yardimci ol markasi falan nedir soyleyiver

Hüseyin bey. Eski bir mesaja cevap yazdığınız için görememiş olmalıyım.. Kullanılması gereken kablo silikon izoleli bakır kablo. Normal PVC izolatör ısıya dayanıklı değil. Ben yaptığımdan beri kullanıyorum. Hiç sorun olmadı. Kablolar ilk günkü gibi

[@josel.sanchez6463]

CONGRATULATIONS. THIS IS THE BEST STICK WELDER PROJECT I HAVE SEEN IN KZbin. EXCELLENT DESIGN, MATERIALS, PARTS, CONSTRUCTION, ASSEMBLING, SHARP AND SAFE. NOTHING TO DO BETTER. I WILL BE WATCHING ALL YOUR PROJECTS.

Thank you so much 👍👍👍👍👍

[@user-de1jq9tf5n]

하이 안녕 👋👋👋 팔방 미인 이시네요 만능재주꾼이세요 다음에도 멋진거 기대할께요 오늘도 너무 좋았어요 잘보가 갑니다 👍👍👍👍👍👍👍👍👍👍

정말 고맙습니다. 다음 비디오는 나무에 관한 것입니다.

[@BasementEngineer]

Very nice and tidy construction! Many years ago my younger son built a TIG welding machine from my father's old Lincoln "tombstone" AC welder. He wanted to be able to weld very thin material, also, and we determined that a large inductor was necessary to stop the arc voltage from dropping to zero. We found no information on the size of the inductor required, except an off-hand comment somewhere that in commercial machines the physical size of the inductor was about the same as the welding transformer. Our scrap stores supplied the requisite transformer, which we re-wound as a choke., using the existing coil wire which we salvaged. With added triac power control this new welder worked very well indeed. Fitted with an arc starter this machine became a very fine TIG machine, too. Adding an arc starter has its own problems. If you wish to know about them, ask me here.

Hello. Firstly, thank you. I am also thinking of using the machine as a tig welding machine. Another follower recommended the idea of ​​using a coil to connect to the output. I'm thinking of doing it by wrapping the cable I used in the secondary winding around a toroid core. But I didn't think of making it too big. If you have detailed information on this subject, your advice will be useful to us. Thank you for your attention 👍

[@BasementEngineer]

@ Thanks for your interest and willingness to learn! For successful TIG welding, an arc starter is necessary so that the tungsten electrode tip does not get contaminated with welded metal. The successful arc starter system consists of 3 major components: 1) A source of high voltage at high frequency. 2) A coupling transformer. 3) By-pass capacitors. The high voltage is needed to ionize the air between the work and the welding electrode, thus providing a conductive path for the arc to begin without touching the work. We used a 10,000 VAC ignition transformer typically used for oil fired domestic heating furnaces. The high frequency is necessary so that the welder does not get electrocuted by the high voltage. Thus the frequency must be high enough for the high voltage to travel over the skin of the welder/machine operator. To produce this high frequency we used spark gaps in series, using small broken tungsten carbide milling endmills for electrodes. Some high voltage capacitors are also required for this circuit. A coupling transformer is needed to superimpose the high frequency voltage onto the welding current. This design was intuitive/experimental and turned out very well. Basically it consists of 2 concentric coils, the inner primary coil is perhaps two dozen turns of wire in one layer, carrying the the high voltage. The secondary winding is made up of 2 layers of welding cable. We found experimentally that placing a ferrite stick from a radio antenna into the centre of this assembly improved the coupling tremendously. Without this ferrite stick perhaps fewer turns of the primary coil would have been necessary. One leg from this transformer goes to the AC input of the full wave rectifier bridge. This next part is most important if you wish to avoid expensive failures! It is absolutely necessary to bridge each diode in the bridge rectifier with the appropriate by-pass capacitor!!! Failure to do so will cause the immediate destruction of at least 2 of the rectifier diodes. These capacitors are AC duty and were fairly expensive from what I remember. Feel free to contact me should you have any specific questions. Bear in mind that I will have to ask my son to elaborate, and may require the partial disassembly of said equipment. Good luck with your endeavour. I trust the foregoing will assist you in your studies for building this apparatus.

Thank you very much for this long and beautiful explanation. You explained in detail. Thanks again 👍

[@Verificador119]

Gracias Maestro!!!! Me has iluminado,hace tiempo quería modificar una vieja máquina,me alegraste el día!

Gracias también por tu bonito comentario. 👍

[@homemadetools]

Good work as always. We shared this video on our homemade tools forum this week 😎

Thank you 👍

[@marioguzmanserrano7934]

Excelente los dos videos, la construcción de la maquin6de soldar y la conversión de AC a CC.. FELICITACIONES.

Muchas gracias. Me alegra que te guste. Saludos desde Turquía 👍

[@user-mb7qj2im4z]

Very great, this is what I have been looking for for a long time. Thank you for your efforts to benefit everyone

I also thank you very much. I tried to make it clear, but if there is anything unclear, please ask.

[@user-mb7qj2im4z]

@ Well my friend, from now on I have subscribed to your channel and is calling to follow your videos and more creativity

[@favourcornelius7268]

Good afternoon sir I'm so delighted to watch your video I see the kind of motivation they are given to us here the work is so beautiful the step-up Is very wonderful I've seen it and is working very perfect congratulation sir

Thank you so much. I'm glad you like it 👍

[@Anonymatter]

A perfect way to arrange the bridges, very impressed.

I'm glad you liked it. Thank you very much 👍

[@Mr19901993]

Awesome 👍 brilliant learned some thing DC welding

[@user-ty5yq5ev3j]

You have useful mind,ideas,for humanity,,thanks from EGYPT...

Thank you very much. I'm glad you liked it. Greetings from Turkey 👍

[@mohamedmoon6431]

مساء الخير كنت بسالك رقم المكثف كام

[@maatiraouki5183]

C’est excellent merci beaucoup pour l’exercice ❤

Merci aussi. Je suis content que ça te plaise 👍

[@Tugrul_33]

Murat Ustam emeğine sağlık. Titiz bir çalışma ile son derece basit ve bir kaç yedek malzemeyle, ömürlük bi makine olmuş. Eski bi elektronikçi olarak, böyle ilginç ve güzel çalışmaları izlemesi keyif verici oluyor.

Çok teşekkür ederim Muzaffer bey. Yaptığım günden beri işim oldukça kullanıyorum. Profesyonel bir alet diyemem ama çok ağır işler yapmayan benim gibi kullanıcılar rahatlıkla kullanılabilir. Tekrar teşekkür eder, hayırlı akşamlar dilerim 👍

[@yazidfryazid5039]

هل يمكنها تلحيم الالمنيوم

[@victorenriquecarrilloorteg5093]

Excelente trabajo, lo hice con 6 puentes de diodo de 35 amp, en paralelo y hasta ahora la maquina me trabaja bien. Exitos

Muchas gracias. No creo que haya ningún problema. Yo también lo uso sin problemas. Saludos desde Turquía 👍

[@kevinaponte7078]

Amazing build quality keep up the great work my friend

Thank you so much. I'm glad you like it 👍

[@BjornV78]

Adding diode bridges in parallel is not recommended, because the diodebridge with the lowest voltage drop will take all the current and burn up, while the other bridges will follow one by one. It's better to choose 1 diode bridge with enough current rating, or use 4 separate diodes with enough current rating. Also, when using DC for stick welding, your welding electrode must be connected to the positive terminal, and your alligatorclip to the negative terminal if you are welding thick material, when using very thin material (sheet / plate), your electrode must be connected to the negative.

Hello. Thanks for the information you provided. I thought about the alternatives you mentioned. However, 250A diodes are very expensive.

[@tony001212]

@ aside from the capacitor you can use a resistor to balance the current in the redtifier bridge so they do not burn.

[@user-lz1xi8qi5c]

Главное работает если ремонт то мастер свой починит.👍👍👍

Привет. Google переводчик иногда делает бессмысленные предложения в русских переводах. Но я уверен, что вы написали хороший материал. Спасибо

[@CoachArt694]

Thank you for sharing your Amazing DIY welding Machine video Murat Sef 💯❤️✔️ Seni seviyorum😊😊

Thank you so much. I'm glad you like it 👍

[@SC.243k]

Fanstastic work 👏👌 thanks my friend👍

Thank you so much 👍

[@felixaponte8364]

@ saludos amigo, por favor cual es el rango mínimo y máximo de amperaje de esta máquina soldadura.

[@zeherculano3223]

Belo trabalho!!!

Obrigado. Fico feliz que goste 👍

[@johnconrad5487]

The build is very good. The largest microwave transformers are rated for abs maximum 1800VA x 2 = 3600VA/40V = 90 Amps. This is without considering losses. You may be able to push it to 100 Amps max. based upon duty cycle. However, the secondary wires in the transformer cannot take 100 Amps. They may be perhaps 60 to 80 amps. Unless you use a small duty cycle like the commercially available welders. whatever, it is still able to supply high enough current to weld. Now you must add the wire feed and the cable although you may be able to just do stick welding..

Hello. In this state, 100A can be taken easily. I agree with you about the cable I used in the secondary winding. However, I found it appropriate to do this in order to obtain sufficient voltage with 2 transformers. I've been using it for over 1 year. Since I used silicon insulated copper cable in the secondary, I did not have any problems. The dimmer circuit I used for current adjustment did not fail at all. I will experiment with adding the necessary equipment for tig welding at the first opportunity. Thank you for your attention 👍

[@josegregoriohernandez8173]

Saludos desde Venezuela, gracias por su exelente presentación.

Gracias también. Esta aplicación realmente funcionó muy bien. Sería mejor usar un solo diodo de 200A, pero los diodos de 200A son muy caros. Estos diodos puente cuestan $1 cada uno. Es bastante barato. Saludos desde Turquía 👍

[@angelobryan4699]

Now I know what to do with all these FWBRs I have stashed....Thanks bro!!!

Thank you too 👍

[@viktorkropolin1866]

Для более лучшего охлаждения под диодными мостами нужно было промазать теплоотводную пасту, и не сверлить под их алюминиевым корпусом отвертиия для воздушного охлаждения. Лишние отвертия резко уменьшают полезную площать для более эффективного отвода тепла теплоотводом от каждого перегретого алюминиевого корпуса диодного моста. Токоотводные медные жилы хорошо и надёжнее припавивать с предварительной их обкруткой места соприкосновения с контактами мостов и толстых медных проводов более тонким медным проводом на 2-3 оборота (D 0,5 mm) Это нужно для более надёжного пропая припоя, который может в любой момент оторваться от постоянного перегрева, плохого качества пайки и сильного окисления контактов при частой сварки во дворе и под открытым небом. Если при плохой пайке случайно разомкнётся хотя бы один некачественный контакт на любом выводе диодного моста, то другие могут быстро испортиться от перегрева.

Привет. Спасибо. Действительно полезная информация.

[@igorbarchan1302]

Основная проблема не в мостах и их пайке, а в сечении вторичной обмотки и сборных шин . Трансформаторы сгорят гораздо раньше мостов т.к. это место с максимальным тепловым сопротивлением.

[@yazidfryazid5039]

هل يمكنها تلحيم الالمنيوم

[@igorbarchan1302]

@@yazidfryazid5039 Нет.

[@ademozturk3547]

@ sizinle nasıl iletişime geçebilirim?

[@javierdesantosjimenez1873]

Fantastic job, fantastic result, thanks for sharing your knowledge, I have an old welding machine but I love messing around with these things, I'll build it for sure, one question, could it be considered an inverter even though it's so basic?

Hola. En primer lugar, gracias. Dado que las máquinas inverter son de corriente continua, podemos decir que el resultado es el mismo. Sin embargo, en las máquinas inverter, el transformador no es así, es decir, no es el mismo sistema.

[@javierdesantosjimenez1873]

@I have seen an inverter from the inside and it is indeed not like that, I have read that it depends, I don't know if on the material to be welded or the diameter of the electrode, the polarity could be changed. With this modification, could the same be done with this group?

Just like you said. There is some information on the electrodes. Specifies which pin should be inserted in which polarity. In this case, you can use it in this machine by changing the polarity according to your needs. What is the maximum current value of your welding machine?

[@javierdesantosjimenez1873]

@t is to be built I have the material and it will be a replica of the one you have shared with us, the machine I saw inside was not mine

👍

[@AyhanErkin]

Murat kardeşim, eline yüreğine sağlık. Ne kadar faydalı bilgi oldu benim için anlatamam. Sağol, varol.

Siz de sağolun Ayhan bey 👍👍👍

[@elizarjerez8177]

thank you so much for sharing your ideas in making simple small welding machine. God bless

I thank you too. I'm glad you liked it. I also shared a video for converting the output voltage of this machine to DC. You can find it on my channel.

[@alform2573]

Параллельное подключение диодов без выравнивающих резисторов ( а в диодной сборке их просто не возможно поставить ) приведет к неравномерной нагрузке на диоды в силу их неодинаковых характеристик и к выходу их из строя со временем. Применять следует либо мощные диоды с запасом по току, либо..... - ( было бы интересно ) синхронный выпрямитель на транзисторах.

И снова здравствуйте. Я предпочел этот метод, потому что одиночный мостовой диод с большим током очень дорог. Я согласен с вами в том, что вы сказали. Насчет балансировочного резистора могу сказать следующее... Так как он не выдерживает такой мощности, то приходится использовать очень мощные каменные резисторы. Это снова создает проблемы с точки зрения стоимости и размера. Вот как я это использую. С диодами проблем не было.

[@user-ec8tr4cg3j]

@ И... причина: идентичость параметров в пределах одной партии.😎

[@aydemiryilkin]

S.A Murat bey. Yine cok güzel ve faydalı bir çalışma olmuş. Sizi tebrik ediyorum. Kondansator 4700 mikrofarat 100 volt sanırım. Birde köprü diyotları paralel bağlamak için kullandığınız çubuk barlar kaç mm kalınlıkta?. iyi çalışmalar dilerim.

Teşekkürler Aydemir bey. Aslında bilgileri altyazılarda vermiştim ama galiba altyazıları acmadiniz. Kondansatör 4700uF 100V , kullandığım bakır kablo 10mm2. Anlaşılmayan yerler varsa yine yazın lütfen.

[@aydemiryilkin]

@ evt alt yazıyı fark etmedim. Cevap için teşekkürler.

Ben de teşekkür ederim 👍

[@robertolson6686]

Wow ... Im just like wow lol ... I didnt even notice you could turn on subtitles lol ... I just figured out my whole problem, im using the wrong capacitor. Thank you guys for this post lol

[@sulistiantoassa7176]

Mantaaap👍👍👍👍kawan hasil karyanya , salam dari pemula mengenal Arus lemah🤗🇮🇩🇮🇩🇮🇩🇮🇩

Saya juga berterima kasih. Sistemnya sederhana dan berfungsi dengan baik. Salam dari Turki

[@josecermeno3685]

Well done!! Greetings from, Barcelona Venezuela

Thank you so much. Greetings from Turkey 👍👍👍

[@wagimaster8499]

용접도 잘 하네요. 작품도 훌륭하고 좋습니다.😂😂😂

매우 감사합니다. 마음에 드셨다니 기쁘네요. 현재는 제가 직접 만든 용접기 2대를 이용하여 발코니 난간을 제작하고 있습니다. 조금 긴 작업이지만 완성되면 영상 공유하겠습니다.

[@MrDionizio29]

Muito bom, meu amigo! Parabéns

Muito obrigado. Estou feliz que você gostou

[@s3rkanAGA]

Bu videoyu görmemişim. Yine mükemmel bir video olmuş, elinize sağlık.

Çok teşekkür ederim 👍

[@narenderverma4203]

Many many thanks for nice vdo with rectifire information how to connect in parallel

I thank you too. I'm glad you liked my video 👍

[@noesierraguzman5864]

Muchas gracias por compartir, y felicidades grandioso trabajo

Gracias también. Traté de responder a sus preguntas sobre la máquina de soldar. Escriba si tiene alguna otra pregunta. 👍

[@Eritreaah]

Best work and brilliant in consciousness

Thank you so much 👍

[@hdl4259]

Sieht gut aus, keine schlechte Idee.

Danke. Freut mich, dass es dir gefällt 👍

Teknik ve güzel bilgiler. emeğinize sağlık. paylaşım için teşekkürler. selamlar. sağlıcakla..

Çok teşekkür ederim hocam. Benden de selamlar...

[@ivancruzluque2795]

Es la mejor q he visto hecha en casa

Muchas gracias. Se calienta un poco, pero lo uso sin problemas.

[@hasantufekci6637]

Elinize, emeğinize sağlık. videolarınızı geçte olsa fark ettim. Zevkle izliyorum ve yakın zamanda kendime de yapmayı planlıyorum. fikir için teşekkürler.👍

Çok teşekkür ederim. Beğenmenize sevindim 👍👍👍

[@joaoalvesdesouza2812]

Muito lingo seu trabalho.amo capricho. Voce está de nota 1000 pelo que vejo em outros vídeo

Muito obrigado. Saudações da Turquia 👍

[@Arnold302]

Very good result.

Thank you so much 👍

[@marckay4489]

Very cool! Kudos

Thank you so much 👍

[@leprechuanes]

Muy bueno el trabajo, al principio noté que era corriente continua por el sonido del arco y me parecía que habías metido una placa de Inverter en el gabinete jajaja

:) No es exactamente el sonido de una máquina inversora, pero es un poco similar ya que es CC. Gracias por tu interés 👍

[@sunandajayakoday5418]

Fantastic job.

Thank you so much 👍

[@whocares457]

Good job Murat👋👍

Thank you so much 👍

[@roimark358]

yes, this is better good job, 👍👍👍👍👍👍⚡⚡🎖️🎖️🎖️

Thank you. I am glad you like it 👍

[@xuanthuyvannguyenthuy4781]

Hello VN rất tuyệt vời sáng tạo hay tuyệt vời nhất chúc mừng bạn thành công hay vui trẻ đẹp hạnh phúc ok

Cảm ơn bạn rất nhiều. Tôi rất vui vì bạn thích nó 👍

[@MrChachacha64]

Simple and reliable.. I will try it also. Thanks for the know how

Thank you so much. I'm glad you like it. It's a well-functioning system. I recommend 👍

[@fabriziobrutti1205]

Ow simple of course but not reliable 😅 ultra-thin heat sink for a power dissipation greater than 200W, no snubbers, nothing to equalize the current between the diode bridges and a capacitor that's actually not needed and that's going to fail very soon because of the huge ripple current

[@khaledfekih851]

Good job 👏👏👏

Thank you 👍

[@eminbayrak5701]

Eline sağlık çok güzel paylaşım için teşekkürler 👍

Ben de size teşekkür ederim

[@devicharansharma2788]

Bahut badiya bhaiya

धन्यवाद 👍

[@harolddgonzalez9086]

Super mejorado esta es lo máximo

Muchas gracias. Me alegra que te guste 👍

[@albertoramonacosta1212]

Esto si esta muy bueno para hacer.una soldadora de plasma igual gracias bro Arg

Muchas gracias. me alegra que te guste

[@zerodegree4471]

Well done

Thank you 👍

[@duyphucle6579]

Bạn có hoa tay vẽ nên vẽ rất đẹp và nhanh rất chuyên nghiệp.

Cảm ơn 👍

[@rabie4x4]

"I have a welding job to do tomorrow, I'll build a welding machine for it today. "

Good luck. If you do my project you won't regret it.

[@johnyfrancis436]

Good job....

Thank you so much 👍

[@iwanadams9892]

Very good and nice I already made 1 with a Panasonic microwave inverter power supply I have tried to make 1 with a normal microwave transformer I had 2 use 2 and it was to heavy so try the Panasonic inverter and with success.

Hello. In fact, it is not an unbearable weight with 2 transformers. Of course the choice is yours. Thank you for your attention

[@thietbidienphuquy]

Good job

Thank you so much 👍

[@sebastiaoferreira1196]

Estava querendo comprar uma retificadora de solda. Mas resolvi transformar a minha máquina de solda eletrica mesmo. Ela é velha, mas é muito forte... E durou mais de 20 anos. Kkk Merece uma reforma "retificada"! kkk

Acho que não precisa comprar um novo. Sólidos e veteranos...

[@jonathanacosta4682]

Excelente Gracias ...

Muchas gracias. Me alegra que te guste 👍

[@mybasics7194]

Nice experience

Thanks. I'm glad you like it 👍

[@genevasimmonds8208]

Nice one

Thank you so much 👍

[@dedihardiat7436]

Good job thank you .

Thank you so much 👍

[@Faheemkhan-zz5wb]

Very nice

Thank you 👍

[@franciscocarvalho7675]

parabens pelo seu progeto

Muito obrigado 👍👍👍

[@DIY-qb9sq]

very good very nice

Thank you so much 👍

[@emreleventyuceler354]

👍Tebrik ederim.👍

Teşekkür ederim 👍

[@Cristuany]

Beata salvajemente buenísimo

Muchas gracias. Me alegro de que te guste. Compartí un nuevo video para el circuito de atenuación que uso en la máquina de soldar. Recomiendo verlo también. Saludos desde Turquía 👍

[@miguellarachpizarro238]

Muy ingenioso para tenerlo a muy bajo costo...

Muchas gracias. Me alegro de que te guste.

[@necdetozkan7762]

Murat bey merhaba saygılar nasılsın arkadaşım eline sağlık bana yapılı gönderebilir misin fiyat olarak ne dir

Teşekkürler Necdet bey. Kusura bakmayın lütfen ama satış yapmıyorum. Malzeme toparlama ve yapma için zaman bulmam zor gerçekten. İlginiz için tekrar teşekkür ederim. Selamlar

[@erickguzman9519]

Amigo trabaja con 3 puentes de diodos bendiciones amigo excelente explicación.

Gracias. Según la teoría, con 3 diodos puente se obtiene una resistencia de 150A, pero en este caso los diodos están sobrecargados. Por lo tanto, utilicé 5 diodos de puente para una operación cómoda.

[@erickguzman9519]

Gracias amigo

👍

[@FlorinTanasa]

Good job man, I wrote an comment but disappear because youtube consider I put a link. Also you can add thermal protection for diodes bridges (some like this exist on office thermal laminating machine) if you search on internet you found something for open connection at 130 degree Celsius, with manual reset and 16A current nominal.

[@FlorinTanasa]

Some like ar33-130-05-w1-s3 maybe work and youtube leave my comment.

These ideas are very nice but come to mind later. I can add, and I hope other viewers reading these comments will also benefit from the ideas. Thank you so much

👍

[@raggoodev2612]

I need to try this.

I think you should try it too

[@serafettindurul9608]

Maşallah.Harikasin

Teşekkürler 👍👍👍

[@shakeralasadee7341]

I admire what you offer on your channel and a follower for two years. I manufactured a crude machine of four transformers. I hope you will help me with how to connect it to a variable resistance to control the voltage in order to raise or lower the ampere coming out of it. I would be grateful if it was a clear and simplified diagram. My appreciation to you, sir❤

Hello. Firstly, thank you. I would be happy to assist you as much as I can. There are 2 schematics in the description section of the welding machine video I made with 2 transformers. One is the general wiring diagram and the other takes the extra triac connection to make the dimmer circuit more powerful. Check out these diagrams and get back to me. I will try to explain how to use a dimmer according to your mains voltage value and total power value.

[@shakeralasadee7341]

@❤

[@shakeralasadee7341]

I am very grateful to you and the description, and I will be following what you create. My dear friend

Thank you too 👍

[@jmanuelldelarosa5138]

El capacitor a qué voltaje se lo pusiste.me gusto tu máquina de soldar muy práctica,para llevar a dónde quieres.gracias por compartir tus conocimientos.

👍

[@vardfriki7274]

Thanks 👍

Thank you too 👍

[@concienciasocial9659]

Excelente

Muito obrigado 👍

[@poerwojadoel7992]

I'm sure you can do it, everyone will turn to your channel because it is very educational and makes others smart, your channel will be bustling. Not everyone can afford ACDC Tig Welding because it is very expensive.

Hello. I agree with you about the tig welding machine. I want to buy it too but as you said it is quite expensive. I'm thinking of adding to this machine. Thank you for your attention 👍

[@poerwojadoel7992]

@ I hope you can do it, I'm always waiting

Hello. I've got this on my to-do list. I'm trying to organize my workshop a little this time. I'm going to experiment with a gas cylinder and torch head. I think it will, but I don't know when. This row I need some wood related tools. That's why I'm going to work on these for a while. Thank you for your attention 👍

[@Abimael2631]

Excelente trabajo, estaba buscando un tutorial para tratar de hacer una y me diste luz para hacerla. muchas gracias

Gracias también. Un método económico y conveniente. Espero que lo hagas y lo uses. Saludos desde Turquía 👍

[@ahmetustun2356]

Elinize emeğinize sağlık

Çok teşekkür ederim Ahmet bey 👍

[@josemedinasilva6811]

Buenos días, esta exelente el diseño, funciona para los Países con corriente 110v

Hola. Primero, gracias. Funciona de la misma manera en lugares con 110V. Sin embargo, es necesario utilizar cables más gruesos en el lado de entrada. Además, el circuito atenuador utilizado para el ajuste de corriente debería ser más potente. La razón de esto es que la corriente extraída de la entrada es mayor en lugares con un voltaje de 110V.

[@andrej9983]

super👍👍👍👍👍👍👍👍🙏🙏🙏🙏

Thank you 👍

[@danieldejean1259]

Excellent, thank you so much. It's was on my mean to do something like tthat. My question can- I use it on a solar regulator charger battery system to replace the solar panels? Like a autonomous free energy?

Hello. You can use this system for battery charging. However, the voltage value must be appropriate. It should also be said. Microwave oven transformers have a heating problem. Good cooling is good for using for a very long time.

[@ivanngambiarras..seescreve3678]

Top

Thank you so much 👍

[@avenger6783]

exelente ....lo voy a mejorar...una pregunta...la entrada de CA de los primarios de vac-110v ...van en paralelo....o...en serie...gracias

Gracias. Las entradas de los transformadores deben conectarse en paralelo. Las salidas están en serie... Da igual el valor de la tensión de red, es decir da igual 110 o 220. La razón de esto es que los transformadores de horno de microondas que se utilizan donde vive se fabrican en consecuencia. Espero poder explicar

[@avenger6783]

Gracias... perfectamente bien entendí

👍

[@Ninja-ul5vk]

nice

👍

[@allgames5384]

Buenas amigo excelente trabajo tengo una duda el equipo es capaz de derretir barra para soldadura en aluminio muchas gracias saludos desde Colombia

Hola. En primer lugar, gracias. Hasta donde yo sé, proporciona los valores requeridos. Sin embargo, no lo he probado.

[@robertoolguin3016]

buenoas dias, no se mucho de electronica, pero podrias decir que triac usas?

Hola. El triac que estoy usando es BT137. Estoy pensando en publicar un video en un futuro cercano haciendo que el circuito aquí sea más comprensible y ordenado. Construiré el circuito en la PCB y compartiré el esquema completo.

[@waltervaldivia2399]

Grandioso proyecto y el acabado está inmejorable. Puedes subir algún diagrama de todos los componentes y conexiones hechas?

Hola. Disculpe mi respuesta tardía a su mensaje. Dado que el diagrama es simple en este sistema, lo dibujé durante el video y no hice un diagrama adicional. Los materiales que utilizo son 5 diodos puente KBPC5010 y un capacitor de 4700uF/100V. También traté de dar alguna información con subtítulos en el video. Puede que no lo hayas visto con subtítulos. Muchas gracias por tu interes. Si el esquema en el video no funciona para usted, vuelva a escribir.

[@miguelangelinfantecorbo5401]

Me gustaría que experimentes con un pedazo del cable de cobre siliconado 40cm ( + o - ) de la pinza al electrodo, para usar el electrodo como un lápis, apesar que tu tienes total dominio usando la pinza. Un abrazo y gracias por compartir .❤

No entiendo exactamente lo que quieres decir en este mensaje. ¿Quieres que use el cable de silicona que envolví alrededor del transformador entre el electrodo y el enchufe?

[@miguelangelinfantecorbo5401]

@ ,Mas bien entre el electrodo y la pinza que es la herramienta que normalmente segura el electrodo, desa manera se puede segurar el electrodo con la mano usando guantes claro! como si fuera un lápiz, como cuando escribes .Gracias por responderme, me dejastes contento , normalmente no me responden, un abrazo. !!(^~^)!!.

Hola, por supuesto, te responderé a ti y a todos cuando tenga la oportunidad. En cuanto al tema que mencionaste... se puede hacer un aparato de este tipo, pero no se puede mantener demasiado cerca debido a las salpicaduras del arco. En este caso, tampoco sería una herramienta muy útil. El calor también es un factor importante. No es muy conveniente considerando estas desventajas.

[@ProMagomed]

Thank you very much for the answers! I'm going to make a welding machine out of *4 transformers,* please tell me how to convert it to DC, what capacity capacitor can I use?

Even if you don't use a capacitor. The capacitor works to start the arc more easily by charging to the maximum voltage value of the alternating current, but it is fully charged again only when you pause the welding process, even for a moment, as there is a continuous discharge situation during welding. If you do not use a capacitor, you will still get DC voltage. Of course, it is not full DC, but it becomes a full wave rectified signal and the sour values ​​of the alternating current are destroyed. If you want to use a capacitor, it can be 4700 microfarads 80 or 100V. The voltage value of the capacitor depends on the output voltage you get. For example, when I converted 40V AC voltage to DC, I got 60VDC and I used a 100V Luk capacitor. I hope I was able to explain

[@oqueedeuseoquechamadodeus5346]

bom trabalho

Obrigado 👍

[@oqueedeuseoquechamadodeus5346]

valeu pela tenção, eu que agradeço@

[@elsaarmstrong-zp6ng]

Clever design! Only thing that would worry me is no fuse or trip on box! If say recticfier shorted catistrophic could take out transformer! Fit antisurge/time delay fuse to stop nusence during welding surges! Btw have you any info on welding aluminium as I am not a welder just an electronics nut retired ! Fraser

Hello again. You are right about insurance. To be honest, I did not install an extra fuse in the box because I was using the machine at home and in a socket with a maximum 16A fuse. I will try to make a filter with a coil on the output side. If I get the result I want, I will share it as a video. I haven't tried aluminum. My profession is also electronics. I'm working on circuit design. Whenever I get the chance, I work on something in my workshop and prepare videos.

[@adrianmarinescu2772]

Super, you can put a induction filter in serie with one of the end

Hello. Another of my viewers also made this recommendation. I will definitely implement this. Thank you very much for your interest and comment.

[@agahgokdag1845]

Sayın Hocam,kaynak makinasının ön yüzündeki pot düğmesi ne işe yarıyor?Akım ayarı içinse oluşumuna açıklama yapabilirmisiniz?(Ben gazaltı kaynak vede TİG kaynak makinasına göz diktim de).Hocam çok özür diliyorum,birinci bölümü seyretmeden bu videonuzu görünce yazdıklarım için.Şimdi sadece ölçüler için açıklamanız var mı ?

Günaydın Agah bey. Ölçüler derken kutu ölçüleri mi yoksa kablo gibi malzemelerin ölçüleri mi? Yorumu doğrultma işlemi videosuna yapmışsınız. Bu nedenle soruyorum

[@RICALRONICS]

Great effort friend. Please can I use winding wire 4mm for the secondary

Thanks. I used 4mm2 silicon insulated copper cable. Honestly, it's a little thin, but I've been using it since I made it and I'm satisfied.