MY 800HP BUILT N54 335I BLOWS UP!! | Engine Teardown 

[@chrisvisme]

Your POV video showed up in my algorithm, been watching all your videos ever since, love the content, can’t wait to see it once it’s running again

[@941garage]

Thank you brother 🫡

[@pedrodagat6909]

U have great passion in the trade! Good job. Still we rise

[@hypertrophy07]

Sorry to have to see yuo go through this. Defintely learned a lot from this tear down. Subscribed!

[@monroemidnight9372]

Id go ahead and get the full 11mm studs right off the bat for the motor, few of my friends who have built their engines all had head lift at high PSI, same issue as yours and had less issue with them. Also might not be a terrible idea to do the closed deck conversion, not as expensive as it used to be! BTW my car is still a ripper with your old kit!

[@941garage]

Your 100% right, 11mm all around is the way to go. I’m still reviewing my option but closed deck and 11mm will be on the list.

[@1SIK335]

Yep mine has those bags to machine the block for it

[@Sitdownbruhh]

Great video. I’m happy to have come across your channel!

[@speedhaus405]

ah man! It'll be back better than before!

[@941garage]

That is the plan, closed deck?

[@slk1771]

@@941garage Absolutely. It's already out and closed deck is great insurance even for 800 wheel.

[@BIGBOOSTPREET]

Timesert the outer four and run 11mm outer with Athena cutring head gasket 85ftlb and retorque to. 85ft lbs after break in never had an issue

[@jimarlonthomas8711]

I freaking love the ending of this video 🐌🐌🐌🔥🔥🔥

[@joshuaquilliam2887]

Wonder if you had a little oil in that stud hole, or maybe used too much arp lube on the stud. I have seen people crack Cummins blocks with ARP 625s this way, and they are thick ass cast iron. From the video that one hole has oil around the stud and no other stud does. Good video, and sucks about the block.

[@nickgerr3097]

Keep it up man! Let`s go

[@gamesposter]

fulcrum's a code name we give to our secret informants.

[@CP-jt6bw]

"Slight" 😂

[@connorclark574]

I feel like maybe some fluid got in the stud bore and hydrolocked when the stud was torqued down, which cracked the block.

[@941garage]

Unfortunately that was not the case, i cleaned and blew out all the threads with break cleaner and compressed air. I guess the block was just to stressed out because it’s been torqued down to 100ftlbs a few times.

[@noahlostinmymind6246]

N54❤️💪

[@1SIK335]

Yessir

[@jaymills85]

As for the supra!! Yeah Manul transmission is the way to go...

[@Jern54]

Ah so you are the one from the spoolstreet post about JB weld the block. 100 ft pounds was way too much. 85-90max. And the oil squirter broke during the first crank probably 😂. Nevertheless I like the content you make!

[@941garage]

That wasn’t me lol but atleast someone else tried. Yes I agree 100ft lbs is way too much. I tried to compensate for the 9mm studs. But hey it worked the first time but I guess torquing the head a second time caused it to crack.

[@Jern54]

@@941garage i sell Full M11 studs in case you are interested

[@PartiBuoy]

Strange that oil looks better than mine

[@slow_s1000]

u torquing the studs down in general, arp says snug them down your're only supposed to torque the nuts on the studs, 30-60-95

[@wilsonvinas5906]

How much boost were you running? And did you have an aftermarket oil cooler?

[@slk1771]

I don't think you cracked it from torquing to spec. Forces in all directions under load exceed the torque spec a few times over. The bolts are probably too rigid. You need a bit of play similar to the block and head material especially running that much boost. My guess is that the head slightly lifted and instead of the bolts yielding they pulled on the threads and cracked the block at the weakest point in the galley.

[@JoshHallie]

Why your bearings that worn? Sometime ain’t right.

[@Jakejacobsonn]

I’d have 13 stripped bolts every clip would be held on my the strength on Zeus .. and all the bolts would be torqued to 9793958nm.. and you managed to get this out in a hour…

[@david-tracy]

Why not weld the block shut?

[@david-tracy]

Good job btw keep it up

[@ZaksWorld14]

What kind of boost were you running?

[@grahamrobson9292]

Very interesting ! Subbed

[@pnwhoons6433]

That’s such a bummer not criticizing but something to watch out for and I’m sure you do but fluid in the head bolt threads will crack the block like that to I had it happen to me on a Toyota good to see you got it going again my N54 cracked a piston today did you have the motor blueprinted or balanced when you built it just curious thinking about building mine it’s single turbo and this is my 2nd motor😂

[@chrisj9256]

What manley rods are those? I got the "economical" rods from them and im hoping it can handle 900whp

[@kingagamer2646]

What exhaust do you use? Btw love ur build u have inspired me to do so many things

[@verify_135i]

Dope video bro

[@duncanbarrie7397]

Over torque or premature crack? It’s an n54 which is how old and you turned the wick up…… they’re solid motors but the price you pay for pushing them to the limit I guess…. Good video tho

[@BEAMERNOOB]

how many miles on that setup?

[@941garage]

9k miles of abuse.

[@ryanlawson5768]

Hey man, what turbo kit are you running here?

[@941garage]

Custom

[@ryanlawson5768]

@@941garage Ahh no wonder it looked different haha, sick job man sounds great 🤙

[@destruxandexploze2552]

JB Weld 🤦‍♂️ No wonder

[@BJ-if2ms]

what oil do you run?

[@941garage]

5w40

[@BJ-if2ms]

@@941garage same I'm on liquid moly 5w40. Thought about the thicker 10w40 that some m3's use

[@kristianfrancis6844]

Vadiiiimmmm😂

[@Kraxt0n]

....whys that supra look familiar af...you in e46owners on fb????????? and by chance do a FUCK load of coding for people who (need) help???

[@941garage]

Sorry that’s not me lol.

[@romuztek]

Last

[@joeychiotis763]

1st