Now I understand, how my R1200GT abs works - there is a small eccentricity ;-) Thanks a lot!
@benvandeventer25216 жыл бұрын
Good work on the video. However I would also tend to agree re the music volume. Also, are you able to please in future show some detail as to how you perform such tasks as pressing the tabs that hold the pump motor? Keep up the good work!
@euro_rfx44993 жыл бұрын
Just about to do the same thing on my Honda. Althought there are screws for the pump and ABS,VSA can be calibrated through the diagnostic that's already inside the car. (By joining 4 and 9 on the obd2 and pressing the pedals and VSA button in correct order)
@johnk.93343 жыл бұрын
Why the unnecessary music? I'm trying to learn something.
@rjright73734 жыл бұрын
Excellent job, I would like to have seen the motor come apart and what the issue was inside of it, just for the curiosity of it. Thanks
@iwillnoteatzebugs2 жыл бұрын
The issue is the brush inside. There s 2 copper brushes , they get stuck
@denismuslic93883 жыл бұрын
Great video. One question please. Why would you reprogram it if you only replaced the motor ? The module and pump were already coded/programmed, right ?
@artemis84074 жыл бұрын
So reviewing this closely, it looks like, (a) IF you can "unstake" a bad pump motor, and (b) replace the motor, ALL while NOT removing teh brake lines / module, (c) THEN, this job can be done without undoing the brake lines and going through the bleed. Agree???
@cbrrebates8 ай бұрын
How did you take the motor off and how did you press it back on?
@antsfur3 жыл бұрын
Good video niCe to see the close up detail you dont get that with other channels. As a matter of interest if you know, is an ate mk70 the same inside as your mk60 ? Also where those 2 horizontal pins are, would there be some o ring seals there to stop the fluid from coming out? And is it possible for these seals to cause it to get stuck? Did you put any grease of some sort on the eccentric part and the that insert as a matter of interest? Also could you use the same motor from another car with the same ate abs unit and swap that over? I know you cant use another different cars pcb (ecu) from the unit. Thanks, so what was wrong with that motor? And what was wrong with your ate unit in the first place? Thanks i know it was 3 years ago !
@antsfur4 жыл бұрын
So what was the problem in the fist place? Had the motor shaft seal gone that was causing it to leak brake fluid into the motor workings? I have the same bloody problem with my pump not working.
@johnson5546714 жыл бұрын
5:17 "I got my old pump, on the new used unit". Wow I'm lost. Not really, but a good video, thank you.
@TheDJF32 жыл бұрын
Please tell me how you get the bearing back inside the pump???
@eduki4 жыл бұрын
There is something that i don´t understand...you don´t need to recode the unit if this is a second hand unit?
@362herbert4 жыл бұрын
Hi Can you please tell me if your motor was liking? Mine does and I have to refill everyday
@luismanuellmf3 жыл бұрын
What could happen if you don't calibrate your dsc?
@TinCanSailor6 жыл бұрын
Enjoy the videos but would like to suggest you turn the background music down a hair more as it tends to drown out your voice a bit.
@aymanhossien95845 жыл бұрын
كيف تم تركيب الموتور How the motor was installed?
@jazzydavis51684 жыл бұрын
Why u didn’t show u taking off the motor
@oldak8647 Жыл бұрын
Brushes costs 10 euros? Just change them in the black head
@николайниколаев-щ2н1ы4 жыл бұрын
Я в восхищении!
@kris87426 жыл бұрын
The problem will be in the brushes of the motor that does not run it can be repaired.
@hendrylopez53555 жыл бұрын
sure it can too
@laszlovoros37665 жыл бұрын
How do you repair it? Taking it apart? Looks like there are no screws.
@diegogasparetto42594 жыл бұрын
With The freaking music on i don't understand well
@florinel181 Жыл бұрын
Praise Lord Jesus 👏
@Surfnet475 жыл бұрын
HOW DID YOU INSTALL THE MOTOR BACK ?
@hendrylopez53555 жыл бұрын
You put it back in place and with a chizzel you hit the aluminium that holds it in place
@salmaniftikhar65835 жыл бұрын
Bro what software are you using for dsc adjustment , it seems its a easy software as compared to inpa
@Customwerx5 жыл бұрын
Salman Iftikhar I was using ista.
@salmaniftikhar65835 жыл бұрын
@@Customwerx Bro can you share me this software in English , and if you could help me its operation , I'll be gratefull
@miarenata12314 жыл бұрын
S4VAGE PERFORMANCE hey buddy how can i get that ISTA software??
@crisnla16 жыл бұрын
How did u pop the motor off and how did u get it to stay once u connected it
@hendrylopez53555 жыл бұрын
hitting the aluminium that holds it in place
@juanrodriguez-ry6yt5 жыл бұрын
bmw what did you expect
@eamh20024 жыл бұрын
Break My Wallet
@gillesnoel2964 жыл бұрын
encore un gros rigolo de commercial qui veux jouer les technicien.
@pristaxau4 жыл бұрын
is he speaking english??...could hardly understand him....
@MondoReman4 жыл бұрын
Do u think this is the kind of video you can put the music in? We cant understand all you say fornthe stupid music!!!