How To Sharpen Drill Bits - Drill Bit Sharpening Jig

In this video you can learn how to easily sharpen drill bits using homemade drill bit sharpening jig. This jig is very simple to make and sharpen various sizes of drill bits in few minutes. Here bench grinder is used to sharpen drill bits.

[@alexandervanwyk7669]

Thanks for showing. I only use my gut. and managed perfectly well over last 4 decades. I always cool bit with water, left side and then sharpen RH side and cool off with water immediately. For small drills need glasses lately. To test drill bit for sharpness; turn with RH in LH finger; if it bites, its always good. Thanks for your professional attention to detail. Love from deep dark Africa

[@delfinosanchez2221]

Ok gracias

[@shahfahad8623]

Hat's off to you sir I appreciate your skills

[@whitehawk7128]

Deep dark Africa? Lol what

[@davidwinkworth6750]

I'm amazed you haven't been clouted by the vice. Clamp it before it jams and breaks your fingers

[@jobspeedmms]

the method used to make the drill bit sharp again is very good and detailed..

[@gregbuckfield9285]

As a qualified sheetmetal worker in fine limit work for 50 years ,you do not sharpen a drill like that .It is at the wrong angle you should twist to get a slight smooth downward curve. The way It is being shown it will not drill a perfectly round hole will chatter . The drills that you buy in all of the D.I Y stores are not sharpened correctly. I always have to resharpen them to do the job properly before using. There is also a correct way to sharpen drills properly for counter sinking holes for screws. That is different from normal drilling. I wish you all the best.

[@Erdogan309]

Bana kendi tekniğini öğretici bir video atar mısın ? Can you send me a tutorial video of your technique?

[@thujudge1]

HAS NO CLUE COULD SHARPEN BETTER FREE HAND AND A LOT FAST !!!

[@philipsutcliffe6014]

This guy is amazing, he's still got all his fingers. It's a miracle !

[@ahmadpepenefendi85]

Tutorial kepepet🤣

[@user-rx6hz4bp4y]

@@ahmadpepenefendi85 قصص

[@Paul29140]

Very impressed, this is how we got things done 100 years ago.

[@piotrekblazucki7357]

Or more ;)

[@hermanteunissen990]

Using cutting oil will make the drill bit last longer and finish smoother. Cool and lube.

[@bobmcgee7805]

on wood ?ha

[@hermanteunissen990]

@@bobmcgee7805 I am not talking about making that wooden jig of course! He is showing how to sharpen drill bits for metal and drills a few holes in metal as a demonstration but not using cutting oil. Do you understand me now? Ask again if you don't.

[@tomvandernoll1455]

@@bobmcgee7805 we have a genius here ( this are drill bits for metal😑)

[@HelloNotMe9999]

With enough lube, we can do anything...

[@aceeeeee5361]

@@hermanteunissen990) lllllllllll

[@manlystyleunder50]

what i learned from this video: you need to know how to sharpen a drill bit before you manufacture a drill bit sharpening jig

[@premanandaran5045]

3

[@user-tl8pg4pf2j]

, ?,,. ! . . , . ? ! . , ! . .. . ? . . , . . , ,. . ! ! . . , ! . .? ! !.!.,, ! , .,! ?,,? .?

[@beatrizarroyo4975]

Ppppppppppppppppppppppp pp

[@beatrizarroyo4975]

,

[@MetinTetiker]

Yaptığınız klavuz veya aparat doğru açı ve düzlem verebilir.Ancak matkap uçları ve kesici aletler sizde biliyorsunuzdur,kesinlikle soğutucu sıvı veya katı yağ ile soğutma olarak kullanıldığında hem yüzey temizliği,hem delici ucun uzun süre kesiciliğinin olmasını sağlar.Küçük eleştirimi mahzur görün.Başarılı çalışmalarınızı takip ediyoruz.

[@uss.steamship9215]

He who has hard wood and knowledge shall prosper…..😁👍❤️

[@nicolemiguelnavarro6132]

sir that was my problem for a long time on how to sharpene drill bit but thanks so much now i know how great video

[@erasethepatterns1]

Here's an idea, start by drilling a smaller pilot hole and maybe use some lubricant. It'll save you a ton of time and larger more expensive drill bits from dulling.

[@parttimetourist]

The spindle looks to be turning too fast for the size of the drill bit resulting in chatter. It also helps to use lube of coolant

[@ihti20]

Приблуда для выравнивания углов, только она для левого сверла. Обычно: правится камень, выравниваются кромки, выравниваются углы, точится задняя, подрубается перемычка, сверлится тонким, но необязательно, снижаются обороты, капается масло, и быстренько, но не спеша, сверлится.

[@denisq937]

Не эт ты слишком загнул для этого гения)

[@rodrigomonardezbalcarce9476]

Very good find!

[@TheJuangiron]

Desde El Salvador 🇸🇻. Bravo. Bravo. Bravo y. Gracias desde Anerica Latina. Hay tantas cosas en las redes de comunicación. Muy buenas. Y es una lástima que muchos las ocupan más para insultarse que para aprender

[@user-qd4zg6ws4k]

Тыльную часть заваливать немного нужно,а то сверлить не будет.для новичка приспособа полезна будет,а со временем научится на глаз затачивать,главное угол выдержать и длину плеч режущей кромки.

[@aunghein9591]

ဗqဖa

[@yakudza75]

Как один раз научили в училище затачивать свёрла, так и по сей день точу без всяких приспособлений, нужно успеть чувствовать инструмент. А рукожоп и с приспособой сверло запорит

[@petergaiser4213]

It's easy to sharpen a large size drill bit. The difficulty is sharpening a 3mm drill bit.

[@hassanmuhamad4011]

⁵vvbby

[@radyarpad857]

Please sharpen me a 60 mm drill thx

[@sergiososa9229]

Buena idea, a pesar de que la platina es very gruesa. En lo que se refiere la prensa, la verdad que también buena idea al hacerla de wood. Felicitaciones.

[@zsir6569]

If you can sharpen the chisel edge, it will make the drill faster and easier to use. If machining deep holes, grinding the back of the knife will be of great help to the row cutting.

[@dangelep]

Best is to use V shape for the sharpening tool. If is round, you will not able to sharp correctly bits with small diameter

[@amigopancho9226]

This is amazing video because of the material used in making jig for drill bit sharpener.Now, I have idea a corrct angle to sharpen my drill bit.t.y. AMIGO.

[@kingronel2348]

Furejiyure

[@meatshield2682]

hard to watch someone put forth so much effort to show people the worst sharpening ever.... nobody should ever do this. i felt like I was watching my 6 year old sharpen a stick and doing it poorly

[@Manish80gyb.]

😊7j kg

[@manoguitaroficial]

Good job man! I like this video, very nice! Emanoel, from Brazil

[@djordjejon4849]

🎓 Exellent main frend👌 Gretings from Serbia 👍👍👍👍👍👍👍

[@tonyowen8547]

Very good you/ve made a useful tool out of a bit of scrap wood very rewarding

[@dipakpatale2106]

Wow... लेकिन आप की लकड़ी की वॉइस बहुत अच्छी है यह पैटर्न देखें मैं घर पर बना लूंगा

[@davidhoward5586]

Never in my life have seen such a loose workshop. If you can call it that? A post drill on a wobbly table. A handheld drill vice and even a wobbly elasticated wanna be drill bit sharpener that is going to hurt this guy bad one day along with everything else he uses in that room. no relief behind the cutting edge Oh no cutting edge that’s why just flat ground to a sharp right angle No wonder it had a hard time burning through that wood A pilot hole would have helped. Maybe He got swarf yet it was burnt. Just hope he learns how to bolt things down and read some basic tool use books or videos before he starts losing fingers.

[@doctorboy5892]

Offensive David. You are watching the head engineer working in the Chinese Great Wall car manufacturing workshop.

[@davidhoward5586]

Well that makes sense now thank you lol

[@fritanke2318]

Looking forward to the tour of your shop and projects. A few hms videos?

[@robertdominiczak6523]

He probably wears open toed safety sandals?

[@dhump59]

​@@robertdominiczak6523 Yes I saw the shot of his flip flops and exposed toes for the metal shavings. lol

[@desmondclarke9444]

Thanks for this video you teach me the way how to sharpen bit i can teach someone to do now

[@ARIFINLATHE]

OmG...nice amazing..👍👍👍👍

[@arunbhatt670]

Nicely done. Real difficulty to sharp small bits. Pl. make a vdo on it.👌⚘🙏

[@needmoreboost6369]

Free hand sharpen! Could have had a set of drills sharpened properly in the time spent stuffing with that block of wood for nothing!

[@04u2cY]

What I find amazing this guy still has his fingers.

[@andyfalc]

Too much clearance angle gives a weaker chisel point. And as demonstrated a tendency to grab. A jobber drill shouldn't be sharpened flat but have a slight curve on the clearance which strengthens the chisel point.

[@henkvharten8465]

like many people said, how not to sharpen a dril bit..

[@Cantstandbs]

Buy a CNC router and learn cad cam. These kinds of DIY tooling projects are good to learn on as well.

[@CodyKlimaszewski]

lol yea because we all just have an extra 100k laying around for a cnc 😂

[@Cantstandbs]

A desktop model like my first one cost about 350 us dollars (3018 from china) . 300mm x !80mm or 12inx 8in It is big enough to do small signs and rigid enough to do aluminum and brass and mild steel. The point being is CNC is doable, But it will take the time to learn. Only after learning would you buy a bigger machine . My big machine does 24x36in 3hp spindle(power) cost 2k that was an investment.. But I can do a lot that I could not do before. I did like your video so keep that up either way. It is only food for thought as I enjoy doing hand work every bit as much s design and CNC.@@CodyKlimaszewski

[@grazynazambeanie5963]

9/16 th hole and no pilot drill . I am impressed

[@saidbaci4344]

Well done !

[@cachhomevideo1546]

Good sharpening

[@sergiokiwon6688]

🇧🇷👍 parabéns Congratulations 🇧🇷👍 gratifying 🇧🇷👍

[@danbrownellfuzzy3010]

Clamping your vise down will keep the whole thing from spinning or flying off the table one day.

[@miranlyan1]

good job bro.I like it thanks

[@user-kz4pe5nd1f]

احسنت ستاذ 💞🌺🙋‍♂️💐💕🌹👏👍🌺

[@vicdelrosario4237]

Thanks for idea. It 's very nice.

[@javierbrito919]

Buena herramienta Saludos desde Campeche México

[@hugohernandez4197]

Felicito a este Señor porque se aproxima un 99% al afilado original de las brocas, no como otros vídeos mentirosos que andan en las redes, no soy un experto en la materia pero me gusta la perfección y la alta Calidad en el trabajo de Taller.-

[@Th6107]

Thank you so much 👍

[@gwangyonglee7596]

Excellent !!

[@charlierogers5496]

Good job done

[@user-zc3ex6ll3q]

Молодчага спасибо так держать всегда

[@christianhowes2]

It's like a bad movie, somtimes just have to watch to the end.

[@johnwilson6298]

The golden rule when drilling. use a clamping tool, OR GET BIT EVENTUALLY!

[@janbalga7702]

Great idea. I will also have to make it because I can not sharpen the drill properly.

[@theskip1]

learn

[@b.p.rwebber8098]

Watch more drill sharpening clips

[@spontankreasichannel01]

Good idea

[@jump4j]

it's easy to sharpen big bits, it's the small ones that are hard

[@dannydizon5224]

Very good.

[@antonioluissantamaria5592]

Very nice...

[@sandiprajguru3294]

Very good ..

[@candidolizardicastro9109]

Gracias por compartir sus conocimientos, es un triunfador.

[@carriestearns7665]

Hey has anybody ever used candle wax for drilling steel when your bit gets hot keep a big chunk by your press and give it a dab also protects bits from rust .good video 👌👌👌

[@kansascityshuffle8526]

I use beeswax

[@wendull811]

I just spend the money and buy cutting oil. It will save you in the long run.

[@rottondog1473]

Vaseline. It melts and coats the drill bit pretty good and nobody in the shop working with you wants to steal it

[@b.p.rwebber8098]

@@wendull811 I use thread cutting fluid works really well because as the bit heats the fluid melt and lasts quite a while. Also use oil but thread paste is way better becuse you just apply it the drill till.

[@josegalote5354]

PARABÉNS AMIGO VOCÊ É UM GRANDE PROFISSIONAL DEUS JESUS ABENÇOE SEMPRE SEUS CONHECIMENTOS E SUA INTELIGÊNCIA.

[@user-ws3vd1vw8b]

تسلم احسن عمل

[@loriamora6202]

you're genius grasshopper...

[@retiredwoodsman]

Nice video

[@sergiofariadepirai]

Super show

[@victorrondon7364]

Excelente video!

[@jhonmcklane3585]

M parece buena idea d cómo sugieres afilar las brocas n los ángulos correctos con la ayuda del dispositivo d madera, pero tambien t sugiero q cuando hagas un corte n una placa d metal uses aceite para corte xq la rebaba sale d color marron o negra xq no sólo c puede quemar la broca sino también el material q estas cortando...saludos

[@cruz1742]

Good Idea.but NEVER HOLD A PIECE OF METAL WITH YOUR FINGER WHILE YOU DRILLING SOMETHING. My Friend got fingers cut off when bit stocked,,!

[@agustinruiz2877]

Excelente video solo una pregunta eso sirve para cualquier broca o se tiene que hacer una para cada broca

[@felipedossantosdasilva9103]

Eu adorei

[@baron8103]

..BUEN TRABAJO..AHORA SI LE AGREGAMOS LIQUIDO REFRIGERANTE ..MAYOR SERA LA DURACION DE LA BROCA...

[@waltgzerod5565]

After all that, I'd rather buy a new bit!! But, Thanks!!

[@fixedit8689]

Free hand it like a true master machinist would do

[@anthrax666]

Very Nice! How many scrap drops of 3/8 flat stock do you have? :) That looks like a very good system for sharping larger bits. I'm looking for a jig to sharpen smaller bits, 3/32" to 1/4". Very impressive how accurate and clean you're jig works. I'm thinking similar jig V-cut that rides on the tool rest. Needs to be quick for a quick touch up. Split point would be nice.

[@sport1349]

verry good

[@airgunsairsofts9490]

Good job!

[@rindingallotirrikladasolat2554]

Amasing add knowledge to me. thank you🙏

[@geanalexandrecavalcante8652]

sai carniça!!!!! zerrrooooooo

[@Pharesm]

damn, your table saw is going to put your hands out of business one day...

[@edijun4391]

thank u for this vidio...

[@keithscott9774]

Think I'll make one too but I'll use a giant chainsaw with blunt teeth to cut the slot. Should get better accuracy.

[@patrickkane7207]

Subbed out to a nonunion shop. LOL

[@83project]

Setelah lihat jadi lebih mantap untuk mencoba

[@kannanrajagopal291]

Nice idea , Instead of using rubber band use a spring.

[@ingvardpedersen1573]

I am a retired industrial toolmaker, and I dont know what, to laugh or cry. Everything in this video is craftsmanship wrong and pretty unsafe. Do yourself a favor and learn how to sharpen a drill bit. It takes less than 30 minutes.

[@anon-iraq2655]

Could you make a video please, or link a video with the correct method

[@atam4023]

+1

[@lylestephens8828]

@Max Z. Sorry Max, but he's right. This is poor technique, and I'm still working.

[@adeelmushtaq4502]

Thanks for making this video made me laugh out loud. 😃

[@szilasmentifazekasjozsef821]

@Max Z. Nincs igazad vagy Te sem tudsz fúrót élezni! Nem ismered a lényegét! A film éppen azt mutatja, hogyan nem lehet élezni!!!

[@zoranmilinkovic4425]

Imam gomilu burgija koje nisu u stanju ni stiropor da probuše!!! Ovo moram obavezmo pokušati da napravim!

[@benjamincastelan5504]

muy bien las ideas para trabajos en. casa

[@Bianchi77]

good idea, thanks :)

[@CariIde0KE]

it is good.i like it.amazing idea

[@rider660r]

Mehhh,I just do them by eye,both brad point and HSS,and likely as fast. To me I think it's a waste of time making the tool,it's not hard to do it by hand.

[@rubenzampieri8127]

Gracias por el video! Te felicito por el trabajo! Saludos desde Ituzaingó, Buenos Aires.

[@fernandoclaudiano3588]

Nota se que a broca que ele afia, fica com o ângulo de corte mais baixo, impossivel ter dado certo, pois ele deve mudar o ângulo de afiamento no gabarito que ele fez, pois está invertido. O correto é fazer o fio, do mesmo pra trás e não o contrário....fica a dica Obs: Acredito que ele trocou a broca ou afiou-a novamentre (corrigindo o erro) pra mostrar o sucesso da idéia 😎

[@rafaelsantos-ui5zn]

A IMAGEM DO FINAL É A MESMA DO INICIO, TEMPO 0:33 E EM 12:56

[@szilasmentifazekasjozsef821]

Igazad van, ez nem valós élezés, éppen fordítva csinálta! A végén javított, de ez nincs bemutatva.

[@JoaoFernandes-jj1ne]

Com o devido respeito para com a pessoa que teve a ideia, mas de facto assim não resulta.

[@fernandoclaudiano3588]

@@rafaelsantos-ui5zn exatamente 👏👏👏

[@danilocosta7220]

Verdade mano .. o ângulo de corte ficou um pouco invertido

[@deomedesferreiragomesfilho7706]

Gostei muito parabéns pela sua criatividade. Vc vende esse gabarito.

[@davidfalconer8913]

Would advise a MUCH slower drill speed for steel and use OIL or coolant ... also make a small pilot hole before using bigger drill ( fast speeds are best for stuff like wood or plastics / Tufnol™ / fiberglass ) and NEVER drill brass with these sharp drills , back off the cutting edge or things go flying around the workshop ( these tips should mean you use your great little jig less often ! ! ) ....

[@dragonshoarddesign3094]

all that for a miter gauge that doesn't even hold the bit still. I use cut off disks on my flexshaft on small bits in my hand, large bits like that use a hardened file and some emery.

[@rayed51]

Well done mate. Thanks for the ideas.

[@salvatoresalvio204]

BELLO E INTERESSANTE VIDEO. COMPLIMENTI. SALUTI SALVIO

[@mas2ery]

Where can I get some of those rubber bands?!!

[@MCsCreations]

Pretty impressive work, dude! Really nice! 😃

[@raymondorr1937]

You obviously haven't checked out the many other youtube vids that show you how to simply hand sharpen a drill in less then a couple of minutes!!!!

[@patriota7801]

hola tienes que destalonarla tambien ya que tiene dos angulos una broca, si no no sirve

[@heyjohnson5535]

I guess if someone can follow what u did they deserve a sharp drill bit we were simply taught how to do it by being shown the angle to hold it and bump it against a base grinder until u take off the burrs and return the original shape to the bit.