Fantastic video! No soundtrack. No hilarious jokes. No discussion about what you had for lunch with your mate who’s gawping in the background. Just a clear concise visual guide on how to strip the E50 with the tedious bits sped. Just what I was looking for. Excellent.
@jaredkaczynski51119 жыл бұрын
I was intimidated to pull apart my E50, but your video helped alleviate that! Thanks!
@gioniponi63772 жыл бұрын
The shaft seal on the ignition Side has to have a Gap from the Bearing, otherwise the bearing doesn't get enough lubricant and breaks within the first few 100 miles or so
@christophermarin32319 жыл бұрын
Thank you for everything! You do great explanation and rebuild videos, they're helped a lot. Don't pay attention to everyone saying you did something wrong or another. You're a great help to people who are just learning.
@lilman17963 жыл бұрын
Thanks for the video my moped friends , Awesome made Video, Lightning, perfect Clearness, perfect Audio, perfect. Keep up the great work everyone ☆☆☆☆☆☆☆☆☆☆☆
@MichaelJohnson-pc9sl11 жыл бұрын
Dude you saved my life on me trying to find new seals and bearings for my E50. Ive looked for over a year for these parts and COULD NOT find them. Bad ass job on the video. How does it run!? man I hope this info fixes the issue im having with mine.
@n1bpd11 жыл бұрын
The flywheel puller uses two M5-0.8mm bolts that screw into the two flywheel holes, measure the distance between them and drill clearance holes in a strip of metal (I used 1/4" by 3" aluminum, not too important so long as its thick). Then I used a 3/8" bolt and tapped/threaded a hole for that between the two M5 clearance holes. Clutch was made the same except it uses M6-1.0mm bolts. If you don't have a tap just put a nut under the metal bar and then use 2 wrenches to pull the clutch/flywheel.
@CORRUPTIONCZARNETWORK3 жыл бұрын
Finally, someone has the correct tool to do the job. love the "microwave trick" of heat-up bearings, great video.
@j.schwarts98372 жыл бұрын
oven ;) microwave would spark like crazy XD
@mAdAsZaC11 жыл бұрын
Its always good to see a ole motor bein revived
@zx8401ztv11 жыл бұрын
Smashing job :-) I had an old puch maxi when i was 17, such a simple and reliable machine, also very forgiving as far as the timing was concerned. . From that simple engine i learnt basic twostroke operation :-))
@wirrkopf Жыл бұрын
Danke für die Ausführliche Darstellung 🤝💙
@tommyshebell26457 жыл бұрын
Amazing video! Kind of reminds me of Wallace and Gromit. Thank you!
@n1bpd11 жыл бұрын
You can use cooling, but unless your using a liquefied gas the amount of contraction from freezing a part in a freezer isn't as much as expansion from a torch because the temperature difference isnt as great. It still might be enough to work, and might be a good option for parts sensitive to heat - just be careful about condensation on the cold part.
@n1bpd11 жыл бұрын
I still have it. There's too much pitting for it to keep a good seal so I was planning on using it to practice crankshaft bearing pressing and alignment.
@hans-petermaier94805 жыл бұрын
Wonderfull what Hamradio Guys can do.... perfect work. Best Regards from DG3IC. VeloSoleX-Adventure-Palatinate
@n1bpd11 жыл бұрын
Not sure if you mean originally or when I re assembled it, so here is answer to both. Really old, probably original sealant so it came off in the parts washer without needing any scraping. I put new sealant on at 33:44
@gymkhanadog4 жыл бұрын
I hope I didn't screw up at 25:20 when I put my seal in. I reinstalled it the same way it was in the old motor and just spaced on the orientation I watched you install it. On mine the open part of the cup was outwards towards the bearing with the solid face of the seal facing the crank. Didn't think anything about it because the seal is keeping ATF out of the motor.
@n1bpd11 жыл бұрын
It isn't running yet (I don't have too much time to put into it) - But with the parts used it should run pretty well.
@eroc26897 жыл бұрын
At 32 mins what's the stuff in the syringe you're putting on the seal?
@BeansBuilds648 жыл бұрын
is that the same engire as in a normal puch maxi s?
@n1bpd8 жыл бұрын
+sjorsbeans Maxi S uses an E50 the same as in the video. It might be slightly different, just small things like 1 ring piston or a different cylinder - but the same engine. www.mopedarmy.com/wiki/E50
@BeansBuilds648 жыл бұрын
Nice, i thought so. Do you have any plans on doing on of these engine rebuilds of an 2 - gear puch ms/mv 50? That would be awesome. I currently have one which i'd like to restore but it's hard to find the information. thnx in advance.
@n1bpd8 жыл бұрын
I made a dissassembly video for the ZA50 engine that came with the moped, but never got around to putting it back together. I'd sent the crank off to get a roller bearing installed and found this E50 while it was away. kzbin.info/www/bejne/jZC2lKSpr56Ia80
@tonjajo737 жыл бұрын
sjorsbeans how to rebuild Zach
@tonjajo737 жыл бұрын
Zach rebuild
@StarliteProductDevelopment10 жыл бұрын
Great how-to video, thanks.
@TheShawna1 Жыл бұрын
I was under the impression that the open end of the seal Faces the oil or grease you appear to put the clutch side seal open end towards the crank web?
@Christianlvm229 жыл бұрын
Wow this videos are VERY relaxing o.o i think its called ASMR? Thanks, very nice videos!
@magnushenriksen8594 жыл бұрын
Thanks!
@dominikhofer526910 жыл бұрын
Saubere Arbeit
@Teeveepicksures3 жыл бұрын
Lol, the clutch spring launching itself across the room @ 15:40
@kostas330711 жыл бұрын
thanks a lot!!! and something else,your video is perfect!!
@n1bpd11 жыл бұрын
Cannot post links in comments, but they are all in the description.
@danielrusbridge41826 жыл бұрын
Hi where do you get your spare parts? I need a gasket set, bearing set big and little ends and a new piston... can you help me? Cheers 🙂
@MR-fw5ih5 жыл бұрын
puchshop.de
@gjorgijanakievskijanakija58669 ай бұрын
Zdravo koje maslo koristi za u mashini i koje je najbolje za mesavinu?
@scott369911 жыл бұрын
great video! I'm about to do this for the 1st time and your video will be right beside me the whole way. Thanks for the bearing remover tool info but what was the tool you used for the 1st bearing you pulled? Kinda like a crazy wine bottle opener.
@cowboywonton4 жыл бұрын
Hello! What jet size did you swap to for your idle and main? Doing the same kit+carb combo as yours! Thanks for the video btw 😄
@jimmyfransen68405 жыл бұрын
How long and on what temperature did you use the microwave for the bearings?
@deanhopkins411710 жыл бұрын
at 24:00 I think the seal on the primary drive is installed backwards, but then I think you corrected it later. Can you confirm this? Thanks! Great video. It helped me out a lot!
@n1bpd10 жыл бұрын
Yeah at 24 min its on wrong (and I did realize and swap it later).
@WigiWare7 жыл бұрын
But if you see and follow the org. Puch exp. drawing, I think at 24:00 You did it right. Why did You swaped it later?
@redrose_6665 жыл бұрын
08:05: OMG, TAKE YOUR PHONE OUT!!! 08:15: oh.. right... :-)
@EllisMalave4 жыл бұрын
What is the name of that tabletop press you have in 24min of the video?
@bozcro6 жыл бұрын
dam i did that 40 years ago. my first bike
@santiagomanuel14727 жыл бұрын
superbe video
@scott369911 жыл бұрын
any chance you could give us an item list on making the flywheel and clutch pullers?
@scott369911 жыл бұрын
never mind. just saw the blurb in the video. missed it the first go round.
@kostas330711 жыл бұрын
ok,and i want to ask you another question,from where can i find a complete engine?
@KevinBording3 жыл бұрын
No space between bearing and seal on ignition side?? 🤔
@jona823a9 жыл бұрын
What is the diffrense between, this motor, and the motor on a puch maxi 2 gear?
@n1bpd9 жыл бұрын
+jonas The 2 speed motors are much more complicated. This bike came with one and I did a tear down video of that, but decided to go with the simpler e50.
@rocksunderwater8 жыл бұрын
Can I pull all the bearings with the HF Bearing and Separator kit 93980? I noticed you used a 3 jaw puller also.. Thanks
@n1bpd8 жыл бұрын
+Ben Anderson The 93980 is the separator I used. The three jaw puller is just one of the ones from Harbor Freight Part 69105.
@mattiasmatsson62058 жыл бұрын
That press looks like it was made for the bearing job. Is it homemade?!
@n1bpd8 жыл бұрын
+Mattias Matsson It's a 1 ton arbor press from Enco, but they sell them lots of other places. I think Harbor Freight sell them.
@marbinchen19916 жыл бұрын
u so lucky! you have a jaegermeister ignition!
@linezgaming26526 жыл бұрын
marbinchen 😂😂😂
@voicesonair11 жыл бұрын
No sealant on the case halves?
@scott369910 жыл бұрын
hey i noticed you did not use countersunk allen bolts for your clutch cover. Any reason why? or comments after having done that? I ordered the kind you used by accident and I don't want to waste time sending them back if they will work fine. thanks.
@n1bpd10 жыл бұрын
I'd have preferred the flat head that have the countersink, but the socket cap work fine - they are a small diameter than the top of the recess so they still center themselves in the clutch cover. I may replace them, but only for aesthetics.
@supicathd37058 жыл бұрын
Did you sell your old zylinder and head?
@leeverink3210 жыл бұрын
WAY TO MUTCH GASCHET PASTE ALSO DO NOT CLOSE THE BEARING CHANNEL NEXT TO THE CRANC if u have no leaks other than the seals u do not even have to use a sealant on the cranck case useing to mutch sealant can cause it to leak inside the engine and cause scaring on the cylinder and piston there was no sealant when u took it apart so u dont need it this is also stated in the puch manual
@osvaldohernandezcollazo80295 жыл бұрын
Quiero ver piezas de cloche puch año 1983motorespuch piezas
@kazz3308 жыл бұрын
starting to rebuild my e50 and your videos are great! Do you grease the bearings at all or just drop them in?
@katrinaslinger28408 жыл бұрын
+kazz330 Hi, just use 2 stroke oil to oil the bearings before assembly.
@kostas330711 жыл бұрын
Did you sell your old crankshaft?
@n1bpd11 жыл бұрын
Try MopedArmy.
@Whocares0505010 жыл бұрын
So.... what are the chances I can pay you to rebuild mine? :)
@benattiamohamed34762 жыл бұрын
Des pièces de rechange
@thalespelegrini39498 жыл бұрын
poderia faser um montando um chicote elétrico ou ensinando como faser a fiacao
@BK-it6wg9 жыл бұрын
can i use this method to rebuild other 1 cylinder engines? thank you :D
@n1bpd9 жыл бұрын
Borut Korosec Not really. This is a 2 stroke single speed which are simple engines to begin with, plus on this the cases split horizontally so you dont need to use a case splitter. Other single cylinder motors will likely split horizontally usually requiring more effort to split them and if they are 4 stroke will have cam's and cam chains and perhaps even a transmission - all those make it much more complicated.
@BK-it6wg9 жыл бұрын
n1bpd thank you :D
@Banafll8 жыл бұрын
what happens if i dont use this honda mass ?
@Maverick_Van_Traveller8 жыл бұрын
you can use grey permatex gasket maker, or any similar gas & oil resistant RTV sealant. Hondabond & Yamabond are just different brands.
@UNKNOWNUSER-jl8nc6 жыл бұрын
what's the name of this thing? 2:05
@n1bpd6 жыл бұрын
It's a clutch puller, you can buy them - but I made my own with a strip of aluminum. Drill two holes to allow bolts to attach to the clutch and then a threaded hole to screw in the large center nut which pulls the clutch off the crankshaft.
@sabotshell9 жыл бұрын
20:10 uhhhh, I've always left those seals in. Have I been living a lie my whole life?
@n1bpd9 жыл бұрын
If they are going inside the cases then remove the covers/shields to allow the oil in the 2 stroke mix or ATF to get to the moving parts easily. When used outside the crankcase (eg wheels) then you keep the covers on them.
@GetMakeIt7 жыл бұрын
Dieser e50 ist ein 1 Gang Automatik oder kein Handschaltung
@robinhirt7776 жыл бұрын
Gett Make It Nur 1 Gang
@MrLarsgren3 жыл бұрын
for these projects make sure you dont buy the engine from a puch mini maxi X30M all gears is cut in other direction and you need to swap all internals for it to fit. they have 1 side of block being red and use a plastic ignition cover. prntscr.com/wipiqy a cute little model on 14 inch wheels.
@DePuchfreak9 жыл бұрын
24:00 Äh wrong side on...
@descoindustries84906 жыл бұрын
dude you f'ed up the lip seal on the drive shaft corrected it and never made a not of it. just fixed it for the end of the video. gosh darn it arrrg.
@daanscheurwater108211 жыл бұрын
Nice, but why are you wearing gloves
@n1bpd11 жыл бұрын
It's mainly to keep my hands clean for when I need to adjust the camera and its boom mount. Lot quicker taking off a glove than having to keep washing my hands or risk damaging the camera.