Navien combi boiler ( E003 error code)

Рет қаралды 23,539

Күн бұрын

Пікірлер

@pritambutter9052 10 ай бұрын

Hello I am also certified plumber and gas fitter. Boiler piping installation in good way and nice . Why you saying it’s messy. Plz focus on your own work . Thanks

@PrecisionDavePlumbingMore 10 ай бұрын

Im glad to hear your a certified plumber and fitter. Nothing wrong with giving my opinion on how a unit was piped up. Im sure you have installed hundreds of Naviens and you your piping is not messy to you. Everyone has the right to there opinions and i do focus on my own work that's the reason why i said this is messy because its missing a couple components that will extend the life of the unit and also efficiency, plus crooked pipes dont help. Thanks for watching and giving your opinion.

@lsteiner 10 ай бұрын

Thanks, lots of information, efficiently presented!

@PrecisionDavePlumbingMore 10 ай бұрын

I'm glad I provided some information on the unit.

@donovanbremmer8248 Жыл бұрын

That install in not messy it looks good from here

@PrecisionDavePlumbingMore Жыл бұрын

Thanks for watching. Stay tuned as this week we are doing a install of a Navien. Don't forget to Subscribe.

@jlatnyc Жыл бұрын

Not a plumber, but the install looked neat, not necessarily art work, but well organized and neat

@PrecisionDavePlumbingMore Жыл бұрын

Yea it's PRETTY neat, not to my standards but ok. It's missing some components and also wasn't piped up 100% correctly.

@ptech88 10 ай бұрын

Install looks fine. I would have used circulators over zone valves but that’s me

@PrecisionDavePlumbingMore 10 ай бұрын

The installation was ok, not up to my standards, but it's works. Yes, I'm with you. I always use pumps for each zone.

@jarrettfinley3704 Жыл бұрын

I had a new Navien combi installed in March and have nothing but trouble with it. It constantly gives e 003 codes. They pretty much rebuilt the whole unit and the gas company replace the valve to the house. Still the same issue. Boiler was deemed a lemon and whole thing was replaced a month ago. Same issues and code again…this is crazy!

@PrecisionDavePlumbingMore Жыл бұрын

I'm sorry, but it's has nothing to do with the unit. I have installed 100 + units and no problems. Usually, 98% of the problem is the installation and the lack of knowledge how to set up the unit. Sounds like you have igniter problems that have to do with gas pressure or offset pressure not set correctly. Did they do a combustion analysis? If they changed the unit because the 1st one was supposedly bad, what makes them think the 2nd one would be bad also.

@jarrettfinley3704 Жыл бұрын

I’m of the same opinion but these guys have done 100’s of installs of these units. A Niven rep is supposed to come look at the install tomorrow. Hopefully we get some answers! It’s cold here in Alaska and this has been a nightmare.

@PrecisionDavePlumbingMore Жыл бұрын

@jarrettfinley3704 Oh, I'm sure it's freezing up there. Would love to see a video of the installation.

@ptech88 10 ай бұрын

Are you sure that there isn’t a slow leak somewhere in the system? No way two units have the same issue.

@Postumeartist 2 ай бұрын

My guess is 1/2” csst has been used. You may use 1/2” black iron for 10ft for newer models, but if it’s csst the diameter is actually much smaller than black iron. I’d be curious what the inlet gas pressure is at the unit when everything is running.

@Jonny-wn1fl 7 ай бұрын

Why start bashing the other company to present yourself as a higher standard when it wasn't the install that was the problem, a part on the boiler went bad.

@PrecisionDavePlumbingMore 4 ай бұрын

So first of all I didn’t mention the other company name so no way to bash them. Im talking about the installation which is not up to Navien standards and definitely not mine either. I dont put myself higher then any other company we all have are own way of working.

@kastenusa 2 ай бұрын

Tankless water heater not coming on This is for my neighbor. The tech stop by and he says it needs new heat exchanger. I was there today just check my self. Give you a code E003 → check gas supply. Valve is open. I clean igniter and flame rod. I'm getting 120v at ingnitor transformer (19kv) but not sure if transformer is any good? Unit was installed 5 years ago. She also noticed that the hot water pressure started slowing down years ago. Please help Model number NPE-180S Thank you

@FrustratedBaboon 8 ай бұрын

"NOT ARE INSTALL" * Should be NOT OUR INSTALL

@PrecisionDavePlumbingMore 7 ай бұрын

Yes sir, I believe it was discussed up already. Thank you for watching

@Mike-lp1vr Жыл бұрын

And how do you vent them out there do you run both out the house or just the exhaust? And you use regular pvc or the gray I’ve seen some plumbers just go 10 inch peice with a 90 and screen on intake side to get air from the basement (lol) I’ve seen these so many ways curious how you do it

@PrecisionDavePlumbingMore Жыл бұрын

I always vent both the intake and the exhaust outside. Sometimes I sleeve the existing chimney with Polypro flex and run PVC to the exterior separately. Or I run Polypro for exhaust and intake to a termination box.

@Mike-lp1vr Жыл бұрын

I’m curious to know what you do as far as maintenance to these out in NJ ? Do you pump in cleaner in it and flush it

@PrecisionDavePlumbingMore Жыл бұрын

So it all depends on if I installed the unit or if another plumber installed it. Only reason it's different is because 95% of plumbers don't install them correctly and need different maintenance especially on the heating side. Definitely always a flush. Thanks for watching don't forget to Subscribe.

@grossmanplumbing3397 11 ай бұрын

good luck ever getting navien on the phone - im so soured on them - hours and hours of waiting on hold and nobody answers

@PrecisionDavePlumbingMore 11 ай бұрын

I'm Navien certified. I get them on the phone in less than 10 min if i need them. Never had a problem with their customer service. Also I have all there part kits for every unit just in case i need parts .

@grossmanplumbing3397 11 ай бұрын

You must have a special number to call them - I wait 3/4 hours every time I call - disgraceful

@grossmanplumbing3397 11 ай бұрын

You must have a special number to call them - I wait 3/4 hours every time I call - disgraceful

@grossmanplumbing3397 11 ай бұрын

You must have a special number to call them - I wait 3/4 hours every time I call - disgraceful

@PrecisionDavePlumbingMore 11 ай бұрын

@grossmanplumbing3397 Yea, that's pretty crazy. I do have a special pin that I use when I call. Usually, I'm only calling for part warranty not to diagnose.

@chrismallory3718 Жыл бұрын

I'm still learning about these units, I have attended the classes but there's alot to know. Btw navien is top knotch

@PrecisionDavePlumbingMore Жыл бұрын

Yes it is, I love installing Navien I take alot of pride when doing them and I believe it comes out like art work. Alot of installation I seen plumbers do they skip steps and just rush. Winter is around the corner for us and I'll be posting alot of maintenance and installation. Don't forget to Subscribe to keep up with the latest videos.

@chrismallory3718 Жыл бұрын

@PrecisionDavePlumbingMore will do man, ive only been plumbing a few yrs doing service and never done a combi just a regular water heater. I've learned some things from you and appreciate the content!