CYma Platininum MP5K Worth It?

[@Pixelponny]

That anti-reversal latch clip must be a god-send

[@ArchieKeen1]

Could also just use some tweezers though the motor hole

[@tylasmith5994]

So cheap to get, every person teching should have one

[@flippyjunior1267]

shut up and take my money

[@TheAde71]

I got mine off ebay

[@bugsstomper7984]

what's the name of that thing and where can be found? Thanks

[@danielk9906]

What you said about aesthetics is so true, i would add that you have 3 stock option: sidefolder, no stock, and the 3 point sling method from the SAS boys being innovative

[@krinkovforever1872]

I’m pretty sure it was GSG9 that came up with the three-point push out method

When I disassembled mine it didn't have any foam or tape around the MOSFET. I guess that one was already manipulated by someone. Also, I used an SHS 22,34mm nozzle for a SIG, and FPS went up very noticeably without any feeding problems.

[@arvo_septus]

I really like the top rail on that. I think it looks pretty cool. But I do agree that the stock isn't right.

[@ivansmokovic]

I read somewhere that the "hot glued sponge" you show is actually a thermal pad they added to help with cooling of the mosfet, transfering heat to the metal gearbox shell. This was done to help reduce the failure rate of the mosfet when firing in semi. Cyma was notorious for burned out mosfets.

[@WazheadBoci]

I own a 041.G and I like it a lot :) And the one hand paddle is rly awesome just a little bit of practice and your reloads will be smooth as butter.

[@Thitnn]

I have the 041G too, replaced the PDW stock with a full MP5A2 stock, took the mag release paddle off literally the day I got it, and replaced the top rail with one of the short ones. 2 ways to go about it haha.

[@WazheadBoci]

@@Thitnn yea personal preference ,)

[@RandomNoisyBoy]

@@Thitnn how did you get a full stock on the mp5k from a mp5? attachment point isnt the same

[@knivessurvives]

dude I found your channel and I'm so glad I did. Makes me more relieved to work on my guns and I'm planning to do some teching for the bois in my airsoft club make some buck

[@TBudgetAngler]

for about $190 USD its a absolute great deal ,unlike the Elite Force that costs way more

[@setsuna200]

The m5sd and limited edition are both cyma.

[@tonyrose2692]

You saved me from buying a pile of it. Thanks

[@darkshock42mlg05]

That's a spongy material on the original etu is actually a thermal pad. Him basically what that does is contacts the gearbox shell which would cause it to act like a heatsink to dissipate heat.

[@johnsamonas7104]

Thanks u saved my mp5 I took your advice worked perfectly,ps your vid’s are great ,love your humor!!!!!!F the haters!!!!!

[@NegativeAirsoftTech]

kisses

[@MercutioUK2006]

Ooo.....ideas........and as I have an MP5k....... *moistness intensifies*

[@n8taing612]

Cyma has a normal mp5k without the mlok and pdw stock as well no MOSFET, I believe it's under their blue line

[@zack8690]

Well. I purchased 2 of these. Wish I waited to see this lol. Not bad but I’m surprised cyma cut some corners. What size tap for the mounting hole Luke?

[@themaniac5864]

The Bevel gear teeth broke fast One year later on my MP5, the 41H. And 6months in, the original mosfet shorted

[@setsuna200]

Why not go tracer/supressor combo? Because if the inner barrel is not too long, it could be done.

[@afkafkafk]

What batteries do you recommend for this one, I got the same model but it doesn't cycle on auto with low C batteries. Just not sure what to get that fits

[@Gap_Poughkeepsie]

Good reviews

[@knivessurvives]

can you test your guns for range and accuracy if you have the means to do so? it will be a great way to support what you're saying

[@rogerborg]

Just slap a Tokyo Marui sticker on it, and those 0.77 Joules will suddenly start outshooting DMRs.

[@error262]

That's not sponge or hot glue. That's thermal glue, they use it to transfer the heat from the fets to the gb shell.

[@Matt-md5yt]

Cyma is the bane of yours and yet it's often on the bench

[@NegativeAirsoftTech]

I love them.... but this wasn't good

[@Trzebiat]

That PDW stock is ugly as hell and you can't even collapse it very much to make the gun shorter because of how long that buffer tube is. I put B&T style stock on it, lots of fitting but worth it. Btw, what nozzle would you recommend for it? I'm upgrading mine, mainly just Warhead motor, Aster V3 and cylinder, but I've been wondering if it's worth it to change the nozzle while I'm at it.

[@obscuragraffitica]

I have the B&T stock on mine as well. A lot of machining but damn, the gun looks proper.

[@tobyc8905]

Would you recommend this gun then? Or have another recommendation?

[@seanmccann1691]

I just put a perun in my umarex mp5k pretty sure it's a cyma gearbox but it does have the screw for the mosfet.i had to do alot of mods to fit zci internal bearing gears and that flat trigger didn't fit had to shave it down and the selector plate piece was a pain had to shave left from your location about 7mm to get it in full auto. Still full auto bursts around 3 or 4 shots and completely shuts off 🤔 any idea 💡 why it's doing this? I can't figure it out just completely lost right now.

[@Hornsvinet]

I just got this one, but how on earth do you fill that mag? (I am new to airsoft)

[@mattmorgan5064]

Putting a perun v3 and warhead 30k brushless in mine, any other recommendations?

[@mattmorgan5064]

also putting a maple leaf bucking and nub in, along with an m115, hard to find a 110mm barrel that I would like to use

[@TheSiliconeSlug]

What did you do to remove the orange tip? Also, what battery are you running?

[@NegativeAirsoftTech]

I'm in the UK no no orange tip.

[@TheSiliconeSlug]

@NegativeAirsoftTech I actually got it off thankfully wasn't too bad thanks

[@Noise-fe6dp]

Any tips on a good mp5 hop unit? They all seem kinda flimsy and some move if you run too much.

[@secondaccount8072]

Have you seen ics mars 2 is it worth it, or are there better options?

[@rdb9936]

What is the best MP5k out the box?

[@Breezyaon1]

Mate, did trim your thumb? Looks shorter I swear

[@planetcaravan2925]

Do any of youre guns feed? You always shoot without mag

[@NegativeAirsoftTech]

Not my gun....

[@cmarriott3835]

Bum sausage

[@hitmanslayer3003]

Surprised you couldn’t get more power out of it.

[@rogerborg]

Yup, that's wank, I'm getting a surprising 1J out of a cheap Galaxy MP5K with an M100 and a 110mm x 6.01mm barrel. Airseal, I guess.

[@m1a1abramstank49]

On the topic of Cyma Platinums, my Cyma Platinum M4 piston makes a hissing sound when going into battery and it doesn’t even shoot air out. I have this odd feeling the rubber mushroom part of the piston head just gets suctioned into the back of the piston head.

[@senpuuxd1032]

How long u use nozzle 22.3mm?

[@cobalt930]

Radiusing on a v3 ? Is that even needed lmao

[@UnusualHat7]

You sound just like Will from The Inbetweeners.

[@julianking4531]

Could you please make a video where you use your 12volt 3300mah battery where you haven’t fucked up the connections like a knob

[@NegativeAirsoftTech]

Pretty difficult request

[@rodolfogaza2517]

Is it advisable to use extended inner barrel for this unit as long as it will covered by a silencer I am very much appreciate your answer for my querry

[@cunnyfred9562]

That Cyma platinum comes with a spare spring. You could easily increase the fps by changing the spring, since this is a quick spring change system., instead of changing the cylinder and/or the barrel. Also, do you have extensive knowledge of the CYMA HIGH SPEED SERIES?

[@kord2003]

Changing the spring won't increase FPS that much. The nozzle is too short, you need at least 1 millimeter longer nozzle for better sealing.

[@TraceurSoul]

Yeah, not really. Tried that on a platinum MP5. It only does around ~1.1j with a Guarder M110 spring when that should take it up to at least 1.4j. It does that because the inner barrel is very short. It's the same with Krytack. If you buy the krytack aeg that comes with 2 uppers you will get ~1j with the short upper and ~1.5j with the long upper without chaning any of the internals in the gearbox.

[@cunnyfred9562]

@@TraceurSoul I think the best option is to change the barrel. A stronger spring will put more strain on the motor and gearbox, so changing the spring will be my last option. Anyway, I think that manufacturers and retailers are deliberately keeping the fps down, because of UK power limits of 1.3 Joules (1 ft-lb) for full auto guns. Its all ridiculous. Gone are the days of full auto AEGs that shoot 450 fps out of the box.

[@Famine_666]

the high speed mp5 series from cyma is phenomenal, or at least that’s what my experience is through my blissful ignorance. my mp5sd high speed performed great stock and even better with an aster v2. 34rps with an 11.1, incredible snappiness, shimming sounds perfect and i recorded a spread of about 6 inches at roughly 160-170 ft with .32s. the only issue i had was that the trigger return spring went out and i had to replace that. aside from that, no issues. a friend of mine has the standard mp5 variant (with the triangle handguard) and it’s similar in performance. i’d say they’re more than worth it.

[@Famine_666]

i forgot to mention that the RPS ratings were recorded post Aster install. before, about 28rps with an 11.1 and 24 with a 9.6

[@MidlandsAirsoft]

ki-ma or cee-ma

[@yted12bme]

It’s not an mp5 it’s a travesty 😂😂😂😂

[@Ultra-Collector]

Luke I have 5 different new ,unboxed ,full metal GBBR and a Full metal H&K MK1 m249 SAW heavy with 16 metal belt rounds. One of the GBBR is a new never opened L85,she’s a really chubby,new version British puppy! I have new metal kits for the KWC/CB mini uzi too! Anything nice you’d like to trade? NEast Uzi etc… What’s your contact? I’ll send you pics! DM on IG?