NEJE Honeycomb Panel for Neje max, big improvement of cutting [unbox / review / first test]

Hy There,
In this video i will show you my new addon i got from NEJE to test.
It's a honeycomb panel for neje 3 max laser cutter, wich make big improvement on cutting quality.
NEJE H8554 Honeycomb Panels, 540 x 850 mm, Laser Bed, Laser Honeycomb Working Table for NEJE 3 Max Laser Engraver & cutter
shrsl.com/3p2zg
neje store:
shareasale.com...
Coupon: V010WZ38E9ZN
(this is my affiliate links, if you buy from that links you get cheaper, and I get a piece of cake)
English language was always pain in the a** for me, I respect every correction, but please be gentle
Thanks for watching.
if you want to support me for more projects like this, my paypal is:
www.paypal.me/...
Hope you enjoy in video and welcome to watch my other channel:
Tine Sedej:
/ @tinesedej8137
Foto, video & editing: Tine Sedej
Camera:
Sony A6500 [sel 18-200 f3,5-5,6 Zeiss touit 50 2.8 macro]
Sony A6000 [sel 30 f3.5macro Sigma 30 1.4]
Music is from: Epidemic Sound:
1: ES_On Guard - Xack
2: ES_Purity - Xack

[@isidoromaich7226]

With a great panel comes great price ;) It matches perfectly to the Neje 3 Max

[@TinC33]

exactly, good product with lot of materiall can't be cheap, another + is that it fit right into neje max ;)

[@Kun373]

big one , love it 😀

[@MONKEY-vi7hx]

Great videos, Thanks. Hi can you please tell me how many litres per minute does your air pump put out.

[@TinC33]

thanks, i got basic 24L compressor, here are it's info: Power: 1.5 kW/2 HP rpm: 2850 U/min max flow: 206 l/min max preassure: 8 bar tanks: 24 l and while working it run about every 5 minutes depend on setted preassure of airassist

[@sutonik300]

Great video, what is the name of the 1mm thick material you used as desk protection?

[@TinC33]

Basic inox sheet, you can buy metal it's much cheaper, 0,5mm will be enough.

[@sutonik300]

@@TinC33 Thank you.

[@mileshkin]

3:41 😁😁😁 "... piece of sheet"

[@huseyinpolat9981]

hello, I just received the lower honeycomb, but it did not fit. am I doing wrong. I would be glad if you help. Thanks

[@TinC33]

what model of engraver you got?

[@huseyinpolat9981]

@@TinC33 neje Max 4

[@huseyinpolat9981]

Can you help me with the installation, my friend, how do we cut. How do we communicate? thanks❤

[@TinC33]

@@huseyinpolat9981 it doesn't fit on neje 4 true, because it's prepared to install L profiles on each thread it got on L profiles, but can do also with honeycomb, i just put few plates of 5mm plywood under, so the honeycomb panel fit over the front and back L profiles and that's it.

[@huseyinpolat9981]

@@TinC33 62 / 5.000 Çeviri sonuçları Çeviri sonucu star_border I understand. can you help me with neje 4 machine working

[@LoremIpsum1970]

Given the cost of this panel, it might be cheaper just to buy aluminum honeycomb, was the steel panel better output than the aluminium honeycomb. Q. Have you tried the E40 module?

[@TinC33]

i think aluminium one work exact same as steel one, pros of aluminium one is that it can't rust, cons is that it's quite delicate and can be demaged quicly, steel one is very tough and magnets can be used to hold the material. defenitley aluminium honeycomb will be cheaper, but don't know where to get one, plus they may be some problem of banding, mine aluminium (small round one) is always a bit bendet on one or another side, if plate will be bigger also that issue will be bigger i think. i got E80 at home but didn't test yet, hope to get time to make a test soon.

[@skylarshockman7659]

@@TinC33 how do you have and e80?

[@TinC33]

@@skylarshockman7659 no i think it's not yet realeased by neje, i edit E40 video right now, but it is not that good as A40640 wich cut about 20mm E40 only about 15mm