NESPRESSO O-ring | Step by step guide to change and prevent leaking

Hello guys
In This video I will show you how to resolve one of the most common problems with Nespresso machine leakage. It is necessary to change an O-ring which to be honest is not so easy to do. Therefore I decide to share with you the guide to do it. Enjoy!
Subscribe to my channel : ‪@benassy69‬

[@arraiolos]

Was going to buy a new machine and this video saved me 70€. Replacement o-ring= 0.25€ and 1hour of pure joy. All the best for you!

[@benassy69]

Glad it was usefull!

[@javidiaz6272]

Ohh great,but I don't know where can I buy this o ring. I live in Spain

[@arraiolos]

@@javidiaz6272 any drug store should have it (tools shop)

[@benassy69]

Ebay. com sear h for "Nespresso O-ring"

[@Ahmyknee22]

You've been incredibly helpful with all these video thank you. I am having the HARDEST time getting the bearings back in 🤦🏼‍♀️

[@DoozyyTV]

Manufacturer: How overly complicated do you want disassembling your machine to be? Nespresso: Yes

[@benassy69]

:)))

[@pleb9622]

Exactly what I thought, I had a Tassimo before, and disassembly was a breeze

[@oliviergan4979]

At 9, 40 I destroyed the clip (one only) ...mission is failed or I could use glue ?

[@benassy69]

I might get away without that clip. The cylinder is pressed during brew, so no spill should occur based on that. Make sure you have the right oring, though !

[@lilianjackson3798]

Thanks for sharing your knowledge - it's awesome to have someone repair things and not throw them away. Your videos are so easy to follow. Thank you

[@patrickmaloy5262]

My Nespresso is old, but still works and just leaks. Your videos have prevented it from being landfill.

[@oldskoolflash1]

There are two o-rings. This one behind the pod, the dimensions for this o-ring is 31.5mm (inside diameter) x 3mm. There is another tiny o-ring inside the boiler unit. The plastic and metal parts can be separated by twisting clockwise (it requires some force). Inside is a black cone with a small o-ring on top. The dimensions of this one is 5mm (inside diameter) x 2mm.

[@benassy69]

Hi Ben. I know I had encountered a couple of times this issue with the small oring behind the boiler. I noticed that if the small oring is the issue is usually water present in the pump chamber and a lot of limescale on the external wall of the boiler. The big problem is that the boiler is extremely hard to remove from the plastic housing in order to have access to the oring and change it.

[@oldskoolflash1]

Yes exactly. I actually found the plastic on mine quite easy to remove, it was like a bayonet lightbulb fixing. I just griped the boiler with gloves and gave a little twist clockwise. It was about the only easy thing on this bloody job so far! I hate it when manufacturers just clip stuff together like this. Thanks for your videos though, they were very helpful in my moment of need!

[@elineweg2452]

Hi Ben, which one should be replaced if the water is coming out where the used pods fall? In stead of coming out the spout?

[@oldskoolflash1]

@@elineweg2452 Hi Eline, I'm not sure I understand where the water is coming out? For me the water was leaking between the plastic and the boiler. I tried replacing o-rings and that didn't work. I ended up replacing the whole boiler unit (which cost about £27). Finally, this fixed it for me. This has been the most painful repair I have ever done!

[@elineweg2452]

@@oldskoolflash1 Ohhh okay then it is a different issue. With me the water falls into that black container that collects the pods afterwards.

[@SenakaSandagomiWeerawardena]

Thanks Mr.Adrian. I got this machine one week ago. Now i know how to DISASSEMBLY the machine. Thanks to you..

[@fotoytall]

Thanks for the magnificent video. I had already disassembled the coffee maker on a previous occasion (it has been so long ago that I no longer remember the fault although I was able to fix it) But this time, due to a water leak, I was not able to get to the problem until I found your video, detailed and efficient. The pity is that it still leaks slightly after changing the O-ring. I have already read in the comments that there is another small O-ring on the boiler. Now I don't know if I'll try it again. The truth is that I don't use it much. The repair was rather a challenge. Thank you anyway.

[@fotoytall]

I write from Spain with the help of Google Translate. I'm sorry if there are errors.

[@silviowel]

saudações brasileiras ao mestre........muito obrigado pela aula de desmontagem e troca da velha peça..............agora vou recuperar minha caeteira, a partir de agora acompanho seu canal sempre ....abraços

[@hardwaresecuritymodule]

Thanks for this, took my own machine apart last night and (hopefully) have the correct size of O-Ring arriving today from Amazon! That was one hell of a job to disassemble - I'd never have been able to manage it without your easy-paced video!

[@hardwaresecuritymodule]

I can't quite believe it, but it worked! First set of o-rings I got from Amazon were obviously too thin, so got the right one off ebay. One point I found tricky was putting the nozzle bit back onto the springs - I thought I had it on, but it wouldn't compress and I took it off and did it again .... apart from that, re-assembly is quite simple. Thanks again!

[@cristinademeo2727]

can you please share the ebay link or the dimensions of the ring? Thank you!@@hardwaresecuritymodule

[@benassy69]

@cristinademeo2727 I have a video on my channel addresing exactly this.

[@manoliucristiangabriel]

Bravo Adrian. Un video explicit pentru tot mapamondul. Respect

[@crpshooter]

I just finished to clean my coffee machine, thank you so much for this video!

[@renatodrubi]

Finally a decent video of reassembly! Thank you so much!

[@MultiJlcs]

Amazing. Now I will try to do all of this with my coffee machine. Thanks.

[@BernardValot]

That was very insightful. I've repaired my machine, using your instructions, thanks you

[@gilbertlippingwell8385]

Hello Adrian. Really great video. Can you please advise what size oring you used? Is it std nitrile or silicone....thanks

[@AlexandrosAvgerinos]

Hi Adrian, many thanks for the detailed repair procedure. Excellent work! What are the exact O-rind dimensions to purchase before attempting to repair? Internal diameter and thickness?

[@Maxhesp]

Thanks from Brazil my friend! Learned quite alot with you. Great job! Best regards!

[@Lordlovaduck]

Great video. Couldn't have opened the machine without it. Thanks for posting!

[@jaf2378]

Thank you, your video was very helpful, I have to do exactly the same with my Nesspresso.

[@NicolasChabu]

Thanks Adrian for your tutorial. I dismantled according to your video. The O ring seems perfect. I connect all parts but still a leakage. There is another O ring to be replaced ? Tks

[@GoliathAngelus]

I solved the water problem myself of my Le cube machine thanks to your video. Its an old machine but good quality,,the next problem is now,,one of the buttom doesn t work but light is still working

[@haythemshady]

How can repair (the water problem)

[@philipekupferman878]

Hello Adrian. After I watched your videos a few times I disassembled my Nespresso machine and want to get the Orings ordered... Thanks for the video. The only thing I feel weird about your videos is that the camera is in front and on top of you and this causes the image to be inverted. I felt a bit confused when I was holding the plastic parts and watching the video to disassemble. Please see if it will be possible to put the camera behind you and maybe it will be easier... Anyway, just a comment. Your videos are very nice.

[@jorgevariasutilidades6443]

Bom dia obrigada pelo vídeo foi o único q achei ensinando a montar parabéns, eu tava tendo dificuldades pra montar aqui um desses e vc ensina muito bem,mesmo com as legendas é muito bem explicado obrigado, vc ganhou mais 1 escrito em seu canal

[@sergioamaro1706]

Minha cafeteira esta co vazamento. Será que se trocar a borracha de vedação, como mostra o vídeo, o defeito acaba?

[@filipeperu318]

Muito bom trabalho consegui arranjar a minha máquina graças à sua boa e profissional explicação...muito obrigado. Bom trabalho.

[@vladimirkotlyarevskiy4045]

Very detailed, clear and professional! Thank you!

[@nelsonelson533]

Where did you purchase your parts from? I am looking for a CITIZ auto primer…

[@Jazzanova666]

Thanks a lot for this very helpful tutorial. Lots of weird plastic sounds. But at the end, this evil machine works like a charm now. Cheers m8!

[@costantinoamato]

Great video HOWEVER, o rings out of there are made of (often) unspecified materials that may not be safe for food contact. Silicone is typically the best choice but all I can find is either Nitrile or fluorocarbon rubber. Krups has done an amazing job in preventing repair shops or dyis to find small parts so I have no idea what material the original o-ring is made of.

[@michallippel5459]

Thanks Adrian for the tutorials. I have an Esenza Mini. When I insert the capsule and turn on the machine, the hot water comes out of the opening of the capsule. It should be noted that the front part with the holes is clean. Any idea what the problem is?

[@razvanbadulescu2765]

Hello Adrian! Where can i find a replacement O-ring from inside the brewing mecanism of a Citiz & Milk?? Thanks!

[@pukatekapo-oj9vq]

Hello, Adrian, THANK you for the video teaching. but you didnot show the original problem? my inissia = the water is leaking from the bottom, is that can be fixed by replacing the O ring ?

[@benassy69]

Hello. The oring causes leaks in the used capsule tray. Your leak is maybe caused by the heater oring or the U shaped link orings. I have a video on my channel addressing this as well.

[@pukatekapo-oj9vq]

@@benassy69 my Inissia works for 7years before it leaking cold water from the bottom, so I am lucky to see your video before I sent it to landfill..... in your video: kzbin.info/www/bejne/aITJnGN_nKpjeNk at the 10:19, I checked the small O-ring which seems ok , and , THANK YOU on this video show me how to remove the retainer (on the small o-ring) : kzbin.info/www/bejne/jISqkKp7mbWjpc0 then, I checked the big o-ring according to your video of : kzbin.info/www/bejne/hoHWgqp9mLhgiKM , at the 10:23, that ring also seems ok I cleaned both rings, and I am waiting for the two new rings I bought online to arrive before I can replace them anyway, then, hope I can put everything back in shape according to your video of kzbin.info/www/bejne/hoHWgqp9mLhgiKM I will let you know the destiny of this Inissia, the landfill, or another x years service :-) Thank You Adrain !!!

[@oricoh]

Hi, I followed and replaced the o-ring, thanks for the video. Now I have a blinking light that doesn't go away. I know about the descaling mode, but holding the two buttons doesn't do anything, I tried 3 seconds, 5 seconds, 10 seconds, nothing works. At some point the water start coming out like in descaling mode but just continued forever I had to refill the tank. Then I just unplugged it because it wouldn't stop. Now it's back to this blinking lights and I can't use the machine. Maybe you have any ideas?

[@armxy]

Very very informative video, all the trick and tip explain in every steps, good job!, subscribed!

[@macitube3734]

hola, magnifico video. puedes pasar enlace para comprar la junta de goma?

[@mw55309]

Hey! Love that you uploaded this video. I followed it exactly and everything worked exactly as you showed and I replaced the o-ring. But it leaks more now than it did before, this time a new leak from the water tank junction. What might have happened for me to mess this up? It didn't leak from there before!

[@benassy69]

Hi. You might have positioned the water tank sear faulty or a joint is not correctly set. Try reposition it correctly

[@mw55309]

@@benassy69 can you post a picture of rust it's supposed to look like? I'm worried I might be missing a part

[@keithgordon639]

Thanks for a very good video, do you have a video for Krups nx250 o ring replacement?

[@rolandohenske1506]

Consegui salvar mais uma maquina graças a sua ajuda, muito bom seu video. Muito obrigado

[@pjvenda]

You know those very brittle clips you mentioned? ... Which part should I order if one of them snapped?

[@johnwang9914]

I just bought a new one from Nespresso and a fair bit of water winds up in the tray with each coffee. The recycling company has already picked up the cardboard box and packing material so it would be a pain to ship it anywhere but this seems quite annoying to replace the O rings myself. Thanks for the video though.

[@raulbuitrago6057]

Excellent tutorial my friend. Thnaks a lot !

[@adolphochacon7984]

Theo best tutorial, ever. Tks.

[@anytrevi]

Thank you!!! 🎉🎉🎉🎉 perfect explanation !!

[@vicsaunders9710]

Adrian, a Big thanks for your video 👍👏👏🇬🇧

[@nunos3250]

Hello from Portugal and thanks for the excellent video, where can you buy the o rings? do you have measurements?

[@javidiaz6272]

I live in Spain,and I don't find where I can buy this o rings too

[@GerlandoAlletto]

Mulțumesc for another great video, Adrian. Beyond the O-ring, my Magimix machine has a flat metal ring, which appears to be broken. Can that also cause leakage? Can share pics if required.

[@benassy69]

That metal plat ring is purely decorative. The capsule make a tight seal on the flat surface on which the aluminium foil is placed. Make sure you use original pods aftermarket ones are leaking du e to lack of a silicone seal. Take a look on one of my Last videos where I explain this....

[@GerlandoAlletto]

@@benassy69thanks, Adrian. I’ll ignore the metal ring and buy the O-ring and replace it. Hope it solves the leakage.

[@Otas58]

@benassy69 Adrian, many thanks for it. I am going to repair it. What is the dimension of the O-ring? I would like to by it in advance? Thx.

[@benassy69]

kzbin.info/www/bejne/j4SUimmFbNWNo7Msi=Zky5D-XNvxF0MAsK

[@Otas58]

@@benassy69 Thanks, bought it, but our problem is that capsule is not punched from front (wider ,aluminium covered) part. Does exist any spare part - puncher? I did not find it.

[@benassy69]

Take a look on my channel. I have a video addressing this problem as well

[@robford1962]

Please can you tell me if there is a component that the nylon pin with the small spring fits into? Does it just fit into the star shaped aperture in the heater unit or is there a piece that I am missing? Hopefully not!

[@robertdodd2087]

Excellent, would not have stood a chance without this, many thanks

[@jpaparicio4066]

Merci, grâce à vos instructions, j'ai reussi en quelques minutes à ouvrir la machine. C'est vrai qu'il ne faut pas hésiter à forcer un peu, ça ne casse pas.

[@cptrasko]

Bonjour, vous avez trouvé le joint en question ? Pouvez-vous me donner le lien, s'il vous plait. Merci par avance. 😊

[@jpaparicio4066]

​@@cptraskobonjour, j'avais mis un joint torique trouvé dans un magasin de bricolage.

[@אריהנדלר-כ3ל]

Hi Adrian bought some types of seals from china and world fluids, I was wondering what type of piston o ring you use?

[@sandramarciasilva1541]

O vídeo muito explicativo. Muito bom, me ajudou muito 👍

[@HassanHassan-pr7nc]

Merci pour votre explication qui m'aide plus de résoudre ce type de problème.

[@jamessteggles4643]

Hi, Thanks for the video, i managed to follow the instructions but the O ring was in great condition. We then tried the machine without the trays in place and surprisingly all was good. The leak happens when pulling the handle to discard the old pod, that's when a ton of water comes out (well, about 10 or 15 mls). Any idea on the issue, maybe as we are not using proper nespresso pods, we are using compostable?

[@benassy69]

It is normal to have residual water in the pot chamber. If you don't have any leaks during the brewing process than it is not a problem with the machine. Could be from the pods itself.

[@fillo1971]

Grazie per il video, assolutamente di aiuto, sei veramente bravo, buon lavoro.

[@brianlobotomy1077]

Very good! I will save my machine and the planet... but where to find the o-ring? Thank you for your video. Very clear.

[@benassy69]

Hi. You can find it on ebay. Search for Nespresso oring. It should have 38mm outer diameter. And 3 mm thick.

[@marcelogarcia6523]

Thank you so much Adrian , but where I can buy those o rings ?

[@benassy69]

Take a look on my last video on the channel.

[@francisgaeremynck6769]

hi thanks for the vid i replace the O ring 31/37/3 and i have still the same leak any idee ?

[@valsanich]

Great video, thank you. I have DeLonghi nespresso EN80 and it has exactly the same construction.

[@lillyminutolo5716]

Where to buy this o ring?

[@valsanich]

@@lillyminutolo5716 deLongi sells a repair kit with spare parts.

[@lillyminutolo5716]

@@valsanich link?

[@valsanich]

@@lillyminutolo5716 google it. YT doesn’t allow links

[@adouban]

Fantastic video, thanks. How often do I need to replace the o rings if I use 2 pods a day?

[@benassy69]

Maybe in 2 years from now...

[@baliya64]

Thanks you saved my machine!!

[@salestonino4683]

Dear Adrian, thank you for all your excellent videos. Ik want to know WHERE you can buy the O-rings for the nespresso machines (stop leaking), thank you Edward (netherlands)

[@benassy69]

Hello Edward, thank you. In some countries you can find it on Amazon but to be sure you can find it on ebay. Search for Nespresso oring on ebay sould be a 38 mm oring.

[@Abyss0s]

Hi, if you break one of the clips holding the o ring what can you do? Any ideas?

[@catialopes9428]

I have broken the two clips... Can it be fixed or I just have to buy a new machine?

[@YK-wz4qx]

Adrian thank you so much for the tutorials, much appreciated! My Inissia leaks a lot from the spout (nozzle) where the coffee comes from. Any idea if it's fixable?

[@benassy69]

It is normal to leak some drops after you finish the brew. It's actually cleaning the pod chamber.

[@nosferatu230]

Very nice explained video. Thank you

[@vickigreiff8215]

Where did you find the correct O ring which is actually shaped as a D ring? Having trouble finding this.

[@javidiaz6272]

Me too

[@אמיראבני-נ7ס]

Where to buy the big o ring ? The one in the exit of the brewing head?

[@benassy69]

Hi check out my last video on my channel. I am addressing this exact topic.

[@mitzulika01]

Mine (same as your model) has a low caudal of water. It does not look like is spilling out water. Just a weak stream. I tried to clean the capsule hole with a toothbrush and apparently got a little better but still not right. How could I fix it?

[@GiuMon1972]

Many many thx Adrián for your video! I safed mi Nespresso Inissia Krups 😍😍 Have you video for pump problem (not draw water from. The thank) for the same machine? Thx

[@benassy69]

Hi Giulio. I have a video on how to disaasamble and clean/ repair the pump.

[@GiuMon1972]

@@benassy69 In your Channel I see only a video for pump repair but for another model of Nespresso 😞

[@benassy69]

The pumps are the same for all coffee machines regardless of the brand.

[@GiuMon1972]

@@benassy69 Thanks for the information. I can update you on my machine: unfortunately the water leak from underneath is still present and I can tell you what the problem could be with this. One of the two plastic hooks that hold the piston hardens with the heat not allowing the piston to remain attached to the base as it should, for this reason the gasket descends favoring the escape of the water. The plastic hooks become very delicate having hardened so much that it is easy to break them.

[@Tiewie100]

Adrian, where can I buy the o-rings? I can't find a supplier. Maybe Ali-Express?

[@benassy69]

eBay.com

[@MarcusVinicius-uw7rb]

Obrigado, ajudou muito seu vídeo 👏👏

[@davidweinstein2620]

Hi Adrian. Perhaps you can help with my problem. My INissia works fine, but the lever has started to jump up once the pump is working. The only way to have it work is to press down and force the lever to stay down. The lever does not open when there is no capsule in the machine and the pump is working. Any insight you can give me? Thank you very much.

[@benassy69]

Hi I only imagine that your brewing mechanism is worn out and it does snap shut one a capsule is inserted. You have to open it and see what joint is causing this. It is not a usual problem of this units.

[@davidweinstein2620]

@@benassy69 Thank you very much. From what I saw, bend the basket for used capsules, there should be a unit that snaps in and serves as a lock to the lever. I'll try to take it out. Can I find a replacement in the market?

[@benassy69]

Yes. You can buy the full brewing head but is somehow expensive for what it is. You can search instead for a defective unit and just swap it.

[@davidweinstein2620]

@@benassy69 Thanks. I'll pursue this.

[@MohamedbenRhaiem]

Thanks for sharing, it helped me a lot!

[@philippepoirier552]

The size of the original o-ring please... Inside, diameter, if you can. 31.5mm (inside diameter) x 3mm it is good ? Thanks a lot

[@benassy69]

Hello. ~34 mm interior diameter. 3mm thickness.

[@philippepoirier552]

@@benassy69 Thanks a lot

[@ricardorachedmicelli4895]

Thanks a lot, very clearly explained.

[@nigeldunnill1959]

Hi, My Magimix Nespresso machine is stuck in descale mode. I have tried all recommended reset options and spoken to Nespresso. Any suggestions on a fix before I scrap it please

[@fabianortiz8152]

Excellent video mate. Thanks.

[@RicardoChiquérrimo]

What is the size of the o ring, and where can I buy it? Thanks

[@benassy69]

I have a video on my channel addressing exactly this 2 questions!

[@jorgevariasutilidades6443]

No 17:28 minuto q vc amostra a parte encaixada ,no meu aqui não tá encaixando fica uma pequena brexa entre as partes já apertei ,soltei várias vezes e seguindo seu vídeo mesmo assim fica essa brexa ,quando eu desmontei não tinha reparado se tinha já essa brexa ali

[@Lordlovaduck]

What are you guys using to wash the parts? I submerged everything in warm water with dishwasher detergent and brushed with an old toothbrush but still some areas are dirty. How about vinegar? Anyone tried it? Thanks!

[@sibeliusbenevides1731]

Excelente técnica e conhecimento do aparelho. Por gentileza, façam um vídeo traduzido para o português (Brasil). Obrigado.

[@alancariglino5593]

Ciao se ti può interessare ci sono i sottotitoli tradotti nella tua lingua apri impostazioni e nella lista trovi la tua lingua saluti

[@blondefullyyours]

where do you buy/get the parts?

[@marekd3758]

Can you provide a link where I can buy the seal (EU)?

[@benassy69]

KZbin does not let me provide links în comments. Search for nespresso oring on ebay you will find a lot.

[@asutton709]

I broke one of the brittle tabs. Is that game over?

[@benassy69]

If you still have one with a new good oring it is still workable.

[@bamboos]

Same here, considering supergluing it ;)

[@Abyss0s]

@@bamboos I broke one too, I think that maybe we should remove the gasket with pressing it and move it without touching the brittle tabs with a screwdriver cause they are veeeery sensitive

[@hanti2734]

Buongiorno! Grazie per il tutorial, io ho comprato le guarnizioni di ricambio su Ebay, già che c'ero le ho cambiate tutte e con poco più di 5€ ho risolto tutti i problemi

[@aaronredpath1070]

After following your video to replace the o ring my machine won't stop flashing the lights I can't do anything. Any idea on what's wrong? Was working fine before

[@benassy69]

Take a look if you fitted the buttons correctly. Sounds like a always pushed button.

[@ramonguzman1596]

i'm not sure if all that work is worth the price of the machine, I'd rather sell the old one and get a new one. But thanks for the video. Cheers.

[@joseab]

Very good tutorial, thank you very much. Could you tell me the size of the o-ring? Or the link where to buy it. Best regards

[@benassy69]

Hello. ~34 mm interior diameter. 3mm thickness.

[@joseab]

@@benassy69Thank you very much for the reply. I was able to disassemble the piston and I measured the rubber gasket and it gave me an external diameter of 37mm and a section of 3mm, from which it can be deduced that the internal diameter should be 31mm?? You leave me in doubt. No problem, and thank you very much because I have learned a lot from your tutorials.

[@javidiaz6272]

I don't know what size buying too

[@emadalzahid4626]

Thanks for sharing your knowledge -

[@martonfeovenyessy4991]

Replaced the oring to a new one 32x38 but it still leaking water into the drip tray quite heavily, no change to prior seal. any ideas? :)

[@haythemshady]

Clean it

[@greatdane3343]

Change the small o-ring in the boiler chamber area.

[@paulbray4928]

Bonjour le joint ou je peux le trouver sur le net j'ai trouvé 42mm celui-là il fait 37mm je trouve pas

[@mohamedlaklaai]

Thanks! you saved my morning !

[@marinastar8120]

My leak is coming from under the machine. Water is hot and it does fill 1/2 cup, but takes almost 3\4 of tank to do so. I am not sure if it's a ring or something else. Do you think it's fixable?

[@benassy69]

You have a clogged diffuser plate. I have a video on how to address this issue

[@marinastar8120]

@@benassy69 Thank you, I will check it out

[@geffridamer9798]

@@benassy69 can you link the video? I have the same problem but i don't find the video on your channel

[@benassy69]

kzbin.info/www/bejne/hIXQoGygrpaXmNU

[@geffridamer9798]

@@benassy69 thank you for the video, unfortunately I have already cleaned that part so that's not the problem

[@faquir885]

hello thank you some much of that vidéo, i had one, and it s pisty i did not show all vidéos that it s the ring we can change it, i did the stape like you, but i di not know that ring it s in faut ( probleme and i do not know which ring it s !! but why you did nit leave the small things inside, for cleaning too, i leave it and it s not problme for put it too inside. Thank you can you give us or show us on the box which daimaetre is ? thank you one thing !! you did not show us in the first things how the water drop, and how it s not drop after fixing it !!

[@benassy69]

The oring is 38mm

[@faquir885]

@@benassy69 and the small one ? 38mm it s external or internal ?

[@pablogc]

In my new inissia, leaks of water are usual since first day. Is It usual ?

[@benassy69]

5 to 10 drops of water for one cup is normal.

[@964964limkyung]

he must be Nespresso Co. as engineer worker? /? very interesting to see how he can fix the difficult machine

[@HendrikusWisker]

Would be helpful to give the size etc. on the O ring(s) so we can try to find them. Also Metric or Inch

[@alejandrobetancourt7513]

Where are you located?

[@theblackdevel5362]

Sir, I have a blockage in the heating chamber, is there a solution please? Thank you

[@benassy69]

Yes. Try to inject vinegar inside and let the reaction clean the limescale.

[@AntonioMartinez-yt1my]

You are very strong 👏

[@benassy69]

😆