NESPRESSO O-ring | Where to Buy one ?

[@boksaboki]

Thanks Adrian, you help me to fix second hand machine that i got for cheap. Works perfect now

[@manoliucristiangabriel]

Bravo Adrian. Esti cel mai tare. Cu o problema de scurgere apa calda / fierbinte ma confrunt eu acum. Tot pentru un Inissia.

[@petergodinez6108]

And thank you for your advise I fixed the start buttons. They were dirty. Now working ok. Only for the leak

[@Murka88]

Hey Adrian, I would be very grateful for any advice regarding a Nespresso Latissima One machine: 1) my milk container is starting to crack and will probably break soon, is there any way other than through official service to purchase a replacement? 2) I'm having a strange pre-brewing leak, the faucet starts to pass hot water a few seconds before actually passing the coffee, resulting in weird taste and wateriness, is this o-ring replacement relevant to my machine or is there another solution?

[@benassy69]

Hello. 1. Spare parts for this machines are extremely hard to find and verry expensive because Nespresso wnats you to buy always new machines. My suggestion is to search for defecti e units on ebay or criegslist and take all accesories from that donor machine. 2. Clean the nozzle and diffuser plate. As far as I remember I dont think the lattisima has this oring.

[@Murka88]

@@benassy69 Thank you for the answer! I have already ordered a torx bit kit to attempt to disassemble my machine according to one of your other videos, but at least visually the diffuser plate "looks clean" I'll also add that the machine does not leak internally (do not see any water leaking when running without the capsule tray) It's my guess that somehow there is a delay between the water running into the chamber and when capsules get actually penetrated. What "regulates" the capsule penetration in the machine other than manually closing the lever? Is there a specific spring? I hope it's not the pump pressure dropping since in that case I guess I'll have nothing to do about it.

[@fingerboarding007bond]

From my machine, about 50% of the water leaks into the drip tray. I opened the machine and upon inspection when inserting a capsule, some water leaks before infusing coffee from around the spout, im guessing an impropper seal when capsule is inserted due to o-ring degradation. Do you think this an O-ring issue ? Machine is grand maestria

[@petergodinez6108]

Hi hello my Citiz machine is leaking a lot of water. Is this the o ring that Would fix it.

[@julioaparicio9226]

Hola Adrian de que medida es la junta ! Gracias

[@zeesadler5530]

Have a Pixie C60 with chrome side-panels. 2 months ago machine started working intermittently. Tried cleaning/descaling. Yesterday machine would not switch on. Noticed a spill of water under machine…can it be fixed and is it worth fixing???

[@zipper168]

Thanks so much Adrian. Following your advice, I purchased a 38*3.1mm (Outer diameter 38mm and thickness 3.1mm hence giving inner diameter 31.8mm) from Taobao and replaced the broken o-ring and it worked right away. Can give the link if anyone interested in knowing.. It's cheap at RMB 4.7 for 20 pieces.!

[@ivangeorgiev7785]

Hi, can I have a link?

[@rafanagigancie236]

Czy będzie filmik o Daihatsu Ferozie

[@NevilleWatson-se1sg]

Hi Adrian, thanks for the videos, very helpful. I found o-rings on eBay (UK)

[@agentmike2222]

Hello Adrian, I have purchased the same o-ring set . But the rings are 3,5mm (not 3 mm) so they don't fit in the nespresso. Do you force it inside?

[@benassy69]

Using a 0.5mm thicker oring will couse it to slip of the cilinder due to higher friction.

[@ioanastanica4310]

Buna seara, dl Adrian! Am un Essenza Mini D30 si stiu ca nu a murit de tot pt ca i se aprind butoanele. L-am dus la un service, dar nu l-au primit. Oare stiti unde as putea sa-l duc in Bucuresti? Multumesc o mie!🥰

[@benassy69]

Bună Ioana. Eu sunt din Timișoara deci nu știu către cine sa te îndrum în București. Problema cu aceste aparate e ca service-urile nu le accepta deoarece în 99%din cazuri costurile de service depășesc costul unuia nou. De aceea eu fac aceste videouri pentru ca lumea sa le poată repara acasă și sa nu ajungă la groapa de gunoi. De cele mai multe ori defectele sunt minore.

[@ioanastanica4310]

@@benassy69 Multumesc mult pt insight!

[@tarak6]

Hi Adrian, I wonder if you can help me here... I have Nesspresso Megi mix Coffe machine which has been working fine but now what I noticed is that it can not Pearce the coffee pods anymore! and so it gives you just the water out rather than coffee! I changed the O-ring after watching your video but the problem is still there! any idea what is the problem? Thank you so much in advance for your help. Harry.

[@benassy69]

I have a video addressing this issue on my channel.

[@tarak6]

@@benassy69 - I would appreciate if you would address me to the the link please. Thank you.

[@benassy69]

kzbin.info/www/bejne/rH_cc2Z4i76orsk

[@marekd3758]

Very good video!

[@NicolasChabu]

Hi Adrian I removed the O ring according to your video. The O ring seems New. There is no damage on it and i have Still leakage. Do you think i have to replace it ??

[@jonoday2077]

I have a feeling O rings can look fine, but they are actually not. Replace it.

[@ChelefKadi]

What is John Turek's number?

[@paulbereholschi5088]

Salutări Scuze de deranj. Am scris un comm la o postare de acum 3 ani cu o boxă Ibiza, am și eu niște probleme și efectiv nu știu cum să le mai rezolv. Iti mulțumesc! Sărbători fericite!

[@benassy69]

Ce problema are boxa mai exact?

[@mohannadbasmaji6624]

Hi Adrian, I have Nesspresso Citiz. Water comes out great with no leaks. But it I put the capsul, the coffee won't come out of the foil side. The knifes works fine. You feel like there is pressure in capsules, but coffee can't pop out. What do you think ?

[@benassy69]

Hi , you need to clean The diffuser plate. That plate has minuscule holes that if not cleaned The pressure online The other side can not punctare The foil.

[@mohannadbasmaji6624]

@benassy69 even if the water (without) capsule comes so easy and clear with NO leaks ??

[@benassy69]

Then I think that The spring behind The capsule holder îs weak

[@mohannadbasmaji6624]

@benassy69 Thanks, you are the best teacher on KZbin.

[@diedericho]

thanks!!

[@Niiixxxx]

Not wanting to sound negative but 8:12 long video to tell us where to buy? I didn't watch the whole thing but at what point do you actually tell us.

[@benassy69]

Just for you if you dont know how to scroll thru an 8 min video. Just skip at 5:20

[@Niiixxxx]

@@benassy69 Thanks

[@qqnea7064]

Felicitari faci o treaba buna dar dece in engleza!?

[@benassy69]

Salut. Multumesc. Engleza findca vreau sa ma adresez unui public mai larg decat doar cel romanesc.