VLANs and Interfaces | Introduction to Juniper and JNCIA Part 3

[@dammyjade4931]

Excellent job!!! Well structured, good audio quality, clear video and rich contents.

[@NetworkDirection]

Thank you! Really happy to hear you like it

[@olalekanallade3703]

God bless you ❤️

[@pradeepchauhan9184]

I watched two ads completely before this video start😂... Love you bro.. Keep it up..

[@NetworkDirection]

Thanks for your support!

[@kylelohse8150]

You are an absolute god send. Thank you so much for these videos.

[@NetworkDirection]

So glad to help!

[@anthonyvoce4775]

God

[@NetworkDirection]

Study notes are here: networkdirection.net/study-notes/introduction-to-juniper/vlans-and-interfaces/

[@rougearlequin]

More informative than Juniper learning bytes.

[@NetworkDirection]

good to hear, thanks!

[@adityashukla9020]

Great video all of them hats of for your way of explaining!!

[@NetworkDirection]

Thanks so much!

[@nawafXjohn]

Thanks for your time. This is very helpful

[@NetworkDirection]

You're welcome! Glad you like it

[@AswiniDas]

Hello. What are the benefits of membership ? Do you have virtual labs to practice ?

[@v12alpine]

Any comments on configuring bridge-domain for mapping vlans to irb's in MX? Otherwise they don't work at all like you expect. This got me at first (coming from old school IOS). Good work on these series. :)

[@NetworkDirection]

I haven't used the MX routers. I've been using the EX switches and SRX firewalls. What should we watch out for?

[@v12alpine]

@@NetworkDirection good question. I am coming from old school 65k's straight to MX204 so the triplet of vlan, irb, and bridge-domains just to set up a L3 routing vlan was mind boggling. I think it's less complex in non-MX. Overall I love the cli much better than IOS though. Except for this!

[@NetworkDirection]

@@v12alpine There's a few pros and cons for sure. I like the CLI, but setting up MPLS in a small environment on small SRX's nearly broke my brain (I didn't do it in the end) - Mixing flow and packet mode was a minefield

[@banglafitnesstutorial5678]

Dear Sir, I can not create van id that means this command is not working on VM " set vlans vlan-name vlan-id 10 " can you help me what issue?

[@leonelgonzalez5747]

I have the same problem

[@NetworkDirection]

What platform are you using? EX/SRX/MX?

[@Lee-qp2et]

Hi, I love your content keep it up. You said along the lines. "If a Primary or Preferred are not configured/selected then the lowest IP will be automatically selected". My question is, selected for what? the Primary or Preferred.

[@NetworkDirection]

I think that would be primary. To be honest, I have yet to face a real-world situation where it's made a difference.

[@mayankbisht3385]

Today I had to configure data & voice VLAN on the same interface. I spend 8 hours tried every method I could search in juniper resources, but it was a failure (couldn't get any worse). Now after watching this video twice I think I know what to do.....thanks

[@network-nub6687]

hi i havejuniper on my eve-ng... i think its different or old model os.. theres no ether-switching after family. please help

[@NetworkDirection]

What version are you running? Have you seen Juniper's V labs?

[@davoudroshanzamir886]

This is what i was looking for, thank you so much, i wonder if there is JUNIPER course to buy? Plz contact me or guide me how to buy it. I deeply need to learn Juniper system.

[@NetworkDirection]

Glad this is helping. I know Juniper have additional paid training on their site

[@PaulKaizer24]

In cisco Interface gig1/0/1 Desctiption User switchport mode access Switchport access vlan 10 Switchport access voice vlan 20 In Juniper ex2300?

[@NetworkDirection]

For the interface configuration: kzbin.info/www/bejne/h2aWZ2hmZ52LmKM

[@braxtonsebayrepairandproje133]

First

[@anoyq56]

1st reply 😏

[@anoyq56]

2nd