❌ never make mistakes when using an electric angle grinder

[@caldeireiro23]

✅how to install hinge 👉🏼kzbin.info/www/bejne/paHWo3uaj5ydbas

[@shan8737]

Instead of having background music, why not explain what you're doing?

[@grantm6514]

Because it's youtube, so there HAS to be music, no matter what, apparently. Also, so the music will become extra annoying when you watch at faster playback speeds.

[@shan8737]

@@grantm6514 true😄

[@twotone3070]

The video is not about angle grinder safety, it's about revenue. Unfortunately by commenting we are assisting in it's proliferation.

[@bigmacdaddy1234]

Why don't you watch and pay attention. Talking will not make it clearer. It's already clear.

[@shan8737]

Attitude!

[@udayamendis1956]

Demonstrator has violated the golden rule.... Never try to replace discs with the power code is connected...

[@caldeireiro23]

🙏🙏👍

[@paulcragg1315]

No mention of unplugging the grinder before changing a disc.

[@2035jim]

I was thinking the same shit that’s the best way to lose a finger

[@jamesbarbour8400]

​@@2035jimabsolutely - safety first - always !

[@Rod-o3g]

Disconnect batteries on cordless grinders too. Learning this the hard way is a good story, but not a story I'd want to tell

[@2035jim]

@@Rod-o3g yeah I’d rather not have to tell that story either

[@NoodlesR6]

Crap man! I change the disk while it's spinning

[@123456zenn]

Good teaching. I learned a lot before using my grinder for the first time.❤❤❤

[@caldeireiro23]

👏👏🤠🙏🙏

[@emm_arr]

"Good teaching." Not really. It doesn't even show the recommended and safe way to install a disk.

[@antonio4463]

Es la mejor herramienta y la mas peligrosa, la uso poco siempre la desenchufo y aprieto con la llave a un amigo que no tenía la protección se le rompió el disco y una esquirla le dio en el corazón ❤️ saludos desde españolandia 🇺🇾👍👍👍

[@caldeireiro23]

Thanks for watching and leaving your feedback! I hope your day is going well 🙏🙏

[@giordanocarpita6580]

Nel video non ha specificato la cosa più importante, e cioè ogni operazione di posizionamento dei dischi, deve essere eseguita tassativamente con la spina della smerigliatrice staccata dalla presa di corrente.

[@dcpowered]

The best video i have found to teach me how to use an angle grinder correctly for the first time! Thanks! 😊

[@caldeireiro23]

🤠🙏🙏🔥🚀🚀

[@hanspflucker4482]

Lo hiciste sin hablar nada, este es el video que estuve buscando, mil gracias

[@caldeireiro23]

🙏🙏🎉🎉🚀

[@lmartinmiami82]

Thanks. Just a bit confuse about the side. Also protections proper clothes, safety glasses, mask ffp3, face shield, ear plugs and leather gloves... it will not fully protect you but should help... And a lot of respect with that tool, personally I am always scared to use it and choose it as last ressources.

[@caldeireiro23]

❤️💝🙏🎊

[@osservatoreesterno2398]

Velocizza di molto il lavoro di taglio , soprattutto dei metalli . Ma quando usi quello strumento devi avere sempre un adeguato rispetto ..

[@bernardocisneros4402]

I'm confused. Do you or do you not use the spanner wrench to tighten the cutting wheel? If you're not supposed to use it, then why does the manufacturer provide one with the tool? Common sense tells me to push button to lock angle grinder and use spanner wrench provided to tighten cutting wheel to grinder. Am I wrong?

[@DVSONENL]

Hand tighten and then give the Cut off disk or abrasive disk a pull to tighten it a bit more and you're good to go.

[@bernardocisneros4402]

@@DVSONENL Thanks, when I bought my angle grinder I tried it both ways and they both work fine, but using spanner wrench takes longer.

[@andrewcoulter525]

Don't use the wrench on the flange nut when fitting a cutting or grinding disc. Just snug it by hand. When the grinder spins up the inertia tightens it up. The wrench is supplied so you can loosen the flange nut when you want to remove the disc. If you tighten the flange nut with the wrench it is possible to over-tighten it which can damage the disc imperceptibly leading to failure of the disc. This is one of the reasons a disc can shatter in use. You should never use a disc you don't know the history of, or a disc that has been dropped for the same reason. Discs also have a expiry date printed on them. Don't use them past that date. Expired discs have a greater chance of shattering because the adhesives holding everything together degrade over time. Keep your discs in a dry environment away from humidity. Humidity can cause premature failure of the adhesive and disc failure.

[@bernardocisneros4402]

@@andrewcoulter525 Thanks for all the good info

[@cristia.6477]

@@andrewcoulter525 It tightens up EVENTUALLY. They put the wrench in there for a reason, don't be lazy if you care for your toes

[@philiprahman6778]

Thanks, I always made mistakes. Now I know what is the correct way.

[@caldeireiro23]

🤠🚀🙏🙏

[@MauV-j2b]

Thank You very much!

[@caldeireiro23]

❤️🥰🙏

[@SloopyDog]

I found out to my cost how dangerous angle grinders are. I was cutting a plastic sewage pipe with a saw blade on the grinder. It kicked back and the blade went down the middle of my index finger also taking off the tip of another finger. Several years ago I was cutting through a brick, the cutting disk grabbed my teeshirt which wrapped around the blade. I was unable to turn it off and it cut a ten inch gash into my stomach. I can not blame the grinder it was my fault for being so stupid. I respect the angle grinder now and follow all safety rules.

[@caldeireiro23]

😳🙏🙏🚀🚀🚀

[@rudyvalentin1789]

I've been cut with a couple of times witn an angle grinder. My quick reaction spared me from losing a finger. Also I didn't blend out because the friction from the blade cauterized the cut at the same time.

[@caldeireiro23]

It really is a very dangerous piece of equipment 🙏⚠️

[@joepro3562]

So for years I've been loading my cutoff discs backwards? I've never had problem, is there something I'm missing? I just went up on a Norton Abrasives video on how to load a disc, why are they showing the wrong way? Put this in KZbin search and see for yourself - How to mount a cutting disc onto an angle grinder correctly. I honestly just want to know which way is correct and why or does it even matter.

[@АндрейНикитенко-ф4с]

Relax, no matter which side. 🙂

[@tassie7325]

I just went and checked my discs as I couldn't make out what it is that he was highlighting and I have no such marking on my discs. To me it looks like a standards approval stamp, just like all the other markings on his disc. I think he just saw what he believed to be a directional arrow and jumped to the wrong conclusion. Additionally, it makes no sense that they would be directional as there are no teeth involved, just abrasive particles.

[@danielkonrad1444]

Makes No Sense to make a directional arrow so small everybody will Miss it. Cutting Discs are Not directional. Put them as you Like. I prefer colored Side Up.

[@francoismouton8338]

merci pour tout ces bons conseils..

[@caldeireiro23]

🙏🙏🤗

[@arturodelagarza9028]

WE LEARN EVERY DAY. WOW GREAT INFO 👍👍👍👍

[@caldeireiro23]

🙏🙏🚀🔥

[@useruser5716]

Ok gracias,; Lo tomaré en cuenta. Saludos.

[@caldeireiro23]

Gracias por tu comentario, siempre debemos tomar todas las precauciones al utilizar la amoladora angular eléctrica. Abrazos 😃🙏🙏

[@Rhotz-ix8ll]

Very useful video and I Shazammed all your music. Thanks!

[@caldeireiro23]

🙏💝🥰

[@SotoLandscapes]

Okay, so, I got a Dwalt XP Turbo diamond blade, tried to cut a stone, and got a ton of sparks and no cuts. What am I doing wrong?

[@caldeireiro23]

🫡🙏🚀💝

[@gregarrell6132]

Read the manufacturer's instructions. They explain the correct way to use the tool. As you become more experienced you will see why some of the safety features bare there. I worked with numerous people who were badly hurt because they thought "it would not happen to them." Wen a blade (particularly ultra thin blades) shatters, it can really cause serious damage to you.

[@ronkali5365]

The first thing most people do is take off the guard, man do i hate those ultra thin blades. I like the bosch, because you can control the speed of the grinder on some models

[@DVSONENL]

​@@ronkali5365always leave the guard on. And the 1 mm cut off disks slice through metal like a hot knife through butter.

[@davidvintr3007]

​@@ronkali5365Nejen Bosch !!! U Bosch platíte za jméno... Mám zkušenost například YATO YT-82020 a NEJSEM DEALER!

[@Paotakloi]

Very interesting. Waiting for next video

[@caldeireiro23]

🤠🙏🙏

[@JoseSanchez-v9k6f]

Talk about safety. The first thing we after buying a new grinder is removing the wheel guard. Now can reach further and into thight spaces.

[@caldeireiro23]

We must always be very careful when using an angle grinder! I wish you a great day 🙏🙏

[@XRavenHunt]

I've made the mistake of taking the guard off once and the result was 20 stitches and a cast on my arm for 3 weeks.

[@caldeireiro23]

🙏🙏

[@guruprasadcv5358]

Excellent advice

[@caldeireiro23]

🚀🚀🚀🤠🙏🙏

[@kaasmeester5903]

Rule 1 of the angle grinder: choose another tool if it will do the job.

[@caldeireiro23]

🫡🙏💝💪

Thanks for the video.

[@princeamongmen7064]

Well I just learned something new from you today and I thank you 🙏

[@gjaguar99]

Para eso es la llave PARA APRETAR No solo con la mano!

[@daviddelair1754]

Eso no lo entendí

[@daviddelair1754]

Para mi no tiene que apretar con la mano

[@ricardoluz...]

Boa instrução ...

[@caldeireiro23]

🤠🙏🙏

[@ПетърИванов-ю9й]

Thanks! Very useful video, Bravo!

[@caldeireiro23]

😀🙏🙏👏

[@francescomiglio2909]

quando si monta il disco, bisogna staccare la spina, fare questa operazione con la tensione si rischia di rimetterci le dita o una mano se involontariamente si preme il pulsante della smerigliatrice

[@caldeireiro23]

🙏🙏🔥🎊

[@ascensaoomega541]

Jamais trocar os discos de corte com éla ligada na tomada!

[@caldeireiro23]

👏👏🙏

[@omnilovismus]

Wenn ich mir das Gefummel ansehe, bin ich froh dass mein Winkelschleifer mit dem X-Lock System ausgestattet ist. Ich kann mir vorstellen, dass dies eines Tages der Standard sein wird.

[@caldeireiro23]

🙏🙏🔥🔥🎉

[@eddieme2009]

Nice, im a noob when it comes to using grinder.. thanks 👍

[@Hewagej]

Amerzon video thank you so match

[@caldeireiro23]

😎🙏🙏

[@kyawkyawthet2631]

❤❤❤❤handle is important because it is broken unexpectedly and hurt my hand.❤❤❤❤❤

[@caldeireiro23]

Thanks for watching and leaving your feedback! I wish you all the best in your life 🙏🙏💪

[@Lanesplitter]

Check the date stamp on the steel ring - the structural integrity of phenolic resin deteriorates with age. A fragment of wheel travelling at 80 meters per second could potentially kill you.

[@caldeireiro23]

Thanks for watching and leaving your feedback! I wish you a peaceful day full of blessings 🙏🎉🎉

[@fakrulislam5404]

thanks a lot

[@caldeireiro23]

😃🙏🙏

[@jerryborges6286]

O cara do começo ao fim do vídeo, Com a proteção errada na Esmerilhadeira,E ainda que ensinar como usar a máquina,É brincadeira ne😅😅😅

[@caldeireiro23]

🙏🚀💝 Obrigado por assistir e deixar seu feedback! Espero que tenha gostado do vídeo.

[@edilsonsilva5668]

Excelente trabalho, muito bom

[@joseivodasilvaivo9020]

Boa tarde Não é necessário mesmo aberto um pouco o disco quando colocar na máquina?

[@hdm6897]

Better to use the wrench to snug the bolt down

[@caldeireiro23]

thanks 🚀🙏🔥

[@aputra6705]

Thanks

[@caldeireiro23]

🙏🙏💝

[@siriosstar4789]

Not well thought out at 1:25 you make a cross with your finger indicating that holding over the motor housing is wrong but then make a check mark indicating that it is right .

[@swishpan]

Gloves?

[@caldeireiro23]

Thank you for informing, I wish you a great day 🙏🙏💝

[@KallenSC]

2:44 is actually wrong:) first time was actually correct!!! ALWAYS put metal ring on disk from ginder!! This protect from breaking disk and jaming disk!

[@caldeireiro23]

👍🙏🙏🚀🚀

[@edithfreeman4367]

Did l miss the part where you mentioned to disconnect electrically when changing the disc?

[@caldeireiro23]

watch this other video👉🏼kzbin.info/www/bejne/aZXNaqecadVmoJo

[@maximusmeridius1240]

Just had 100 stitches from using an angle grinder , never will i touch one again.

[@caldeireiro23]

🙏🔥🚀

[@FirstAnDariel]

1:54: Shorcut OSA means Organization for the Safety of Abrasives! It has nothing to do with the disc setup!

[@caldeireiro23]

❤️💝💞🙏🚀

[@Eagle0000]

Tomando la amoladora lo mas atras posible sin obtruir las ranuras de ventilacion se obtiene mayor control sobre ella en el video se ve que practicamente la esta ahorcando con la mano

[@caldeireiro23]

😃😃🚀🚀

[@barrysmith8193]

Say here’s a thought……. How about creating tools that are safe and appropriate for left and right handers alike? This right handed grinder sucks for left handers. I have other tools that blow saw dust into my vision and eyes not away like right hand action. We left handers should get some sort of credit on the purchase price for having to accept unequal consideration, or at a least “right Handed Version” should be printed on the packaging.

[@repetemyname842]

Not enough Southpaws in the population to make it worthwhile for the companies. Sucks, I know, but thats how corporations work.

[@danielkonrad1444]

Dude, rotate the shield and Put the handle in the other side. All anglegrinders are two sided.

[@williamlorimer060867]

This video is funny the first thing you do with a new grinder is to throw away that handle

[@davidvintr3007]

Při řezání je kotouč vertikálně držadlo také a je to pro praváky nešikovné. Levé předloktí je nad ochranným krytem. Pro broušení je vhodné aby byl kotouč horizontálně a držadlo také, vypínač je nahoře.. Toho lze dosahniut JEN přetočením převodovky proti motoru. Prakticky je potřeba mít dvě úhlové brusky. 👋👋👋🤠👍

[@Igorpetrovskyj]

Это надо смотреть "супер умным" для техники безопасности 👍

[@pjwoo276]

why didn't you just use a shovel to point to that microscopic directional arrow on the disc ?

[@caldeireiro23]

🙏🙏💪🚀

[@danmetalgods5048]

Esta errado a instalação do🎉 disco, a porca tem que ficar em contato com a parte metalica do disco.

[@caldeireiro23]

🤠🙏

[@eufemiaruizmendez9294]

Si vas hacer una demostración siempre utiliza la llave

[@caldeireiro23]

💝❤️🎊🙏

[@drnh4444]

There used to be something called common sense.... unfortunately those with none need videos like this

[@caldeireiro23]

Thank you for watching our video and leaving your feedback! have a great day 🙏🙏🚀

[@OptimusOne]

Stopping a grinder with your fingers is a quick way to find out if you qualify for a nickname like "Stubby."

[@caldeireiro23]

🙏🙏🚀

[@IOANCHRIST-GODSTEF]

Most Importantly, When You Change Discs PULL THE CORD OUT OF THE ELECTRIC SOCKET, So You Will Not Start Accidentally The Angle Cutter!

[@caldeireiro23]

🙏🙏💝🤠

[@hjerneStimulanz]

i did not understand the last thing?

[@caldeireiro23]

🤠🙏💝❤️

[@nikiandreev7923]

Why the last one is wrong

[@caldeireiro23]

❤️🙏

[@лексирин2]

0:42 это тоже правильно и будет работать Зачем вводить в заблуждения есть разные чаши и машинки с гайкой тоже разные и твой спосб может быть не верным с перевернутой гайкой

[@caldeireiro23]

🙏💪🤠

[@hugohernandez6726]

Nunca corten madera se traba y salwn para cualquier lado me corté la altura del pecho..

[@caldeireiro23]

Thanks for watching and leaving your feedback! May your day be blessed 🚀🚀🙏🎉

[@rooteroman]

1 - El sentido de giro de un disco, si es necesario, se indica muy claramente con una flecha GRANDE visible a simple vista con forma CURVA y lo que tú muestras en el video es parte de un logotipo diminuto. Observa un disco de corte de diamante y verás lo que intento decirte. 2 - No te he visto utilizar guantes o gafas de protección. 3 - La máquina incluye una llave para fijar la rosca de apriete que tampoco has usado en ningún momento. Creo que debes aprender a usar una amoladora correctamente antes de dar consejos a los demás. Un saludo.

[@miguelonubaelandevalo]

@igorshevchuk77, efectivamente amigo este tipo se cree que la llave la trae para hacer bulto

[@marceloalexmenezes2797]

Quer ensinar mas Botou o disco de corte virado!

[@miguelonubaelandevalo]

Pues ahora me entero yo que la llave que traen la amoladora angular es solo por gusto o para hacer bulto

[@caldeireiro23]

Uso la tecla solo para soltar el disco. 😎👍🤝

[@boutrosalkhouri4523]

You can’t say aweseome to your self, when people watch they decide about it not you, 😂.

[@caldeireiro23]

😃👏👏🙏

[@danieltarcho9324]

Me parece a mi... a miiiiiiiiiii. Que la llave, Y ES COMO ME ENSEÑARON, sirve para para ajustar y desajustar la tuerca de apriete del disco SEA CUAL SEA. Y QUE NUNCA SE DEBE APRETAR Y DESAPRETAR A MANO, por que un disco de corte puede estar dañado y lastimarte.

[@totoky4826]

Faltaron las explicaciones de todos modos gracias

[@caldeireiro23]

🙏💝🚀❤️

[@ianhillman4007]

Narration instead of annoying music would have made this video 1000 times better...

[@caldeireiro23]

thanks for the suggestion 😃🙏🙏🚀

[@Олег-и1е2я]

Не въехал, как ставите круг? Знаю по науке, круг ставится мет шайба вниз. За кожух лайк. Тут со своими соратниками бьюсь, что б кожух ставили обязательно. Без кожуха это пижонство. Тем более производительность падает. Искра летит куда попало, плюс все аремя в напряжении.

[@caldeireiro23]

😃👏👏🙏

[@michaelschofield1537]

Why did you not use the peg spanner to tighten the outer flange before you ran it up? Contravention of regs right there, not good education, hand tighten is NOT acceptable

[@caldeireiro23]

thanks buddy, I'll check it out 😃😃

[@Ren.P.]

key always is a locker for electric grinder...

[@caldeireiro23]

🙏💖❤️🎊

[@BHP15]

OK now, I did not know that i could fasten the disk with my hand without grinder tools. i am killing myself using it to fasten the disk.

[@caldeireiro23]

🙏🎉🚀🚀

[@danielcep1879]

Excellent, clair, brillant!!Merci...

[@carlosatiles9964]

first mistake for safety change the disc with the grinder disconnected and have safety gloves to start working or continue working

[@cpaoutdoors9926]

I have done it once it has no mercy on human skin

[@caldeireiro23]

🙏🙏💝❤️

[@manuelmosquera1038]

Nunca lo hago ..

[@caldeireiro23]

😃🙏🙏

[@al-bp1pi]

Never force the grinder, let it do it job.

[@caldeireiro23]

🙏🙏🤩🚀

[@лексирин2]

и ключей от них у меня нет не вижу смысла от их присутствия и постоянно нужно не потерять. всегда рукой откручивал и закручивал. если закусило то газовый ключь или клещи в помощь а когда купил шайбы от закусав вообще не было ни разу момента когда нужен этот ключ. и да на машинках с такой шайбой в комплекте ключ не кладут в комплект так как он не нужен

[@caldeireiro23]

🙏🙏💪🚀

[@лексирин2]

да без защиты не как но я их снял с обеих машиноки работаю уже 20 лел максимум что происходило это синяки от кусков диска даже одежу не рвёт

[@caldeireiro23]

🙏🙏

[@silmarsoares2010]

A chave que acompanha não serve pra nada então?

[@caldeireiro23]

A Chave é usada apenas para soltar a Flange, nunca para apertar. 🤝👍

[@abranco4523]

Nunca usei nem pra uma coisa nem pra outra

[@FC-qe1wl]

The guard he is using is for grinding, NOT cutting. There is a different guard for cutting. But even a wrong guard is better than NO guard

[@caldeireiro23]

Never use the angle grinder without protection 🙏🙏🚀🚀🔥🔥

[@peritobrasil]

I almost lost my feet using this equipment.

[@caldeireiro23]

Thanks for watching and leaving your feedback! I wish you all the best in your life 🙏🙏🎉💪

[@daniel27959]

No se vos pero yo voy a seguir usando la llave para ajustar el disco

[@seanmodaressi5599]

Why wasting so much time showing the wrong way first and then the right?????!!!!!!

[@caldeireiro23]

🙏🙏🚀

[@xander9460]

People learn better from mistakes than seeing the right thing straight away

[@albertbordelio986]

No dia que as empresas colocarem o manual junto com o equipamento, muita gente vai conseguir usar com segurança

[@1891kmk]

Uhhh I’m pretty sure they do not sure what the hell u r talking abojt

[@migueljimenez1338]

Why when somone makes a video thinks every body its going to like the music they used on it?.

[@caldeireiro23]

I'm sorry you didn't like the music in the video. 🔥🙏

[@artyfhartie2269]

Never use a grinder to clean your hands

[@caldeireiro23]

🙏👍🚀

[@jboyblog2003]

Bibili ako

[@caldeireiro23]

🙏🫡

[@repetemyname842]

I know its not recommended but I run mine without a guard. As long as you keep an eye on the disc and dont get cheap you should be alright. You can also use your grinder to cut about 1 1/2" off the guard making it easier to use one. Again, not recommended but theres just so many things you need to see better while you cut, just keep the grinder angled away from your face while cutting in case the disc blows.

[@stitchbiatch3715]

Same! I upholster boat seats for a living, and use the grinder mainly to remove frozen bolts from the wood bases. You can't really do that with the guard on, as it impedes vision and also you can't get into tight spaces sometimes.

[@bigmacdaddy1234]

Yeah, and when the disc blows you will wish you had the guard.

[@LDU2U]

@@bigmacdaddy1234 That's why you have safety glasses . Wearing safety glasses are a pain in the arse, but....? .

[@tracer1127]

Yeah and when the disc blows to bits and they do occasionally trust me that guard will be all that’s protecting you from serious injury. If it explodes and hits your safety glasses you may get lucky but if it hits your face you are going to have to pray that the plastic surgeon is good.

[@florinpandele5205]

Angle grinders are one of the most dangerous tools to use. While a circular saw is very similar, the angle grinder spins at a much higher speed, and the physics say that energy increases with the square of the speed. These things can, and will literally take your head off if they get stuck.

[@emgee8483]

Safety first.

[@rodolfomautino2196]

El primer disco de corte está puesto al revés☝🏻

[@caldeireiro23]

🙏🙏

[@jeffreystephenson6946]

There is an arrow to tell you direction on the machine you muppet

[@brat210787]

👍👍👍👍👍👍

[@caldeireiro23]

🙏🙏🚀😉

[@laloreyes2397]

Dislike, no entendí el número 3 de sobre que lado se pone el disco, ni el último el del segurito, en lugar de poner música de fondo deberías explicar lo que vas haciendo

[@caldeireiro23]

Gracias por el comentario, me esforzaré por mejorar la explicación en mis próximos videos 🙏🔥

[@kuzukapama]

*çok sesli Arka plan fon müziği rahatsız edici , dikkat dağıtıyor* 👎

[@caldeireiro23]

🙏🚀💪

[@arkonman]

the second is wrong

[@caldeireiro23]

🙏🙏🎉🚀

[@yukio5232]

やっぱ、Xロックが一番👍✨

[@caldeireiro23]

🤠🙏❤️