New software fuel table offset and cal stuff.

We added the ability to adjust the fuel table in the handheld and unlocked the ability to upload and download tune files. #acesefi #aftermarket #chevy #engine #fuelinjection #acesfuelinjection #automobile #blazers #howto #lsswap #lsswapped #lsswaptheworld #software #tuning

[@SHSPVR]

One thing Ace EFI needs is a user forum, I got I hope get motor installed soon and thanks and I bookmark this.

[@actionvulture5251]

There is an owners page that is helpful.

[@SHSPVR]

@@actionvulture5251 Oh I forgot to ask where ?, final got motor on test stand being that ACE is close today the cam option, as I have BTR Truck Norris would that be considered mild or race being that there's nothing in the manuals that would give me a general hit where it needs to be set

[@SHSPVR]

@@actionvulture5251 by the way I post a video of mine

[@urielelias3059]

They have a FB group page, real helpful.

[@JakeT22290]

Can you have multiple tunes saved to the Jackpot handheld? Such as a “cruise” tune, “eco” tune, “race” tune?

[@actionvulture5251]

Yes you can. Just make your tunes and save them. When you need to release the bald eagles just pick the freedom maker tune. If you want the mpg then put the basic one. And send it.

[@ck9180]

Great video. Just wanted to know if monitor can be disconnected after initial set up? Installing 2bbl set up on stock Cutlass Supreme with V6 engine for senior citizen who doesn't want the monitor showing. I figure I can just hook it up any time need to check or make adjustments. Just wondering if system will run without monitor hooked up. Thanks!

[@actionvulture5251]

After I get my adjustment done. Let it learn then turn off the o2 sensors when it drives good I usually disconnect the handheld. It has no issue

[@jongraham4118]

Hey I’m thinking of getting the aces jackpot but I’m wanting to know if I can use Dakota digital gauges with it or what I will have to do to make the Dakota digital gauges work.

[@actionvulture5251]

Working on that.

[@CEProductions04]

So your saying I can download a tune from a different software and transfer it to my aces software?

[@actionvulture5251]

No just aces to aces. The values do not mean the same because of how the math works.

[@websterterrebonne5213]

So this will work with the killshot as well ?

[@actionvulture5251]

Yes it does. First one I did was in my camper on my power station.

[@drepofolk]

So no matter what if your running trans controls you need to select drive-by wire?

[@actionvulture5251]

@@drepofolkyes the dbw firmware has everything in it. I know no one has ever said that before but I wanted to touch base on it.

[@r000OO00tt]

will a msd cam sync distributor work with this

[@actionvulture5251]

This is on a LS based motor. But for most classic sb engines a 7+1 Hall effect setup will work if you set it right and make it as a cdi in the wizard

[@bigbug6900]

Looked at mine is at a 154% and afr still going to 17.1 plus

[@actionvulture5251]

Sounds like a bad sensor

[@sunneysunney9761]

Hello will this work with the duces wild??

[@actionvulture5251]

All systems except high roller.

[@sunneysunney9761]

ok so this is just a direct down load of your websight then@@actionvulture5251

[@doc4244efa]

Does this work on 5” also ??

[@actionvulture5251]

Yes it sure does.

[@doc4244efa]

Do I need the 2.08 update? Just did 2.07.

[@doc4244efa]

@@actionvulture5251 hey Tim, tried to do this last night but there is no “fuel table offset” on my 5” handheld. Someone from Aces said I need 2.10 firmware ?? Do u know when that will be out ?? Thanks, Eddie

[@jameerchavis6135]

@@doc4244efaI have the same question you have here, I tried on the 5” and don’t see it

[@jameerchavis6135]

@@doc4244efa yes there is a new update as of 2/5/2024 2.10 you have to download load that to the handheld

[@chrisulloa7141]

I got the jack pot , it’s only firing on one side

[@actionvulture5251]

Make sure you crank and cam are syncing up. What setup you got.

[@chrisulloa7141]

@@actionvulture5251 aces jack pot , 6.0 ls 799 heads , new cam sensor , got fuel , got spark and 200 psi compression .. only firing on 2 .. dead 4 6 8 … I’ve reset the wizard 3 times

[@chrisulloa7141]

The system just fouled my plugs - on the 60 lb system Is that the pressure on the fuel line supply or the lbs on injectors

[@johng83]

My got fouled twice already

[@johng83]

@@chrisulloa7141I’m betting fuel supply hey man lmk if yours get resolved I did the swap my issue is fouling the plugs changed all gaskets just goin down the line now I’m leaning towards the jackpot I need to adjust like this video

[@B5S0H5E0L5F0M]

Firmware steadily getting better each time. Here's to hoping for ITB specific tables soon 🥸

[@actionvulture5251]

Oof itb stuff is a little more complex

[@B5S0H5E0L5F0M]

@@actionvulture5251 I figured. I have a decent idea on tuning it with the reg VE tables, but still checking in about alphaN before I start letting the learning software have a go at it.

[@actionvulture5251]

No alpha N yet but I be bringing that up for future stuff.