NEW SOUND SYSTEM WIRING AND MORE FOR MY 93 GMC SIERRA OBS TRUCK..PART 2 SpinningwrencheswithJ

IN THIS VIDEO I INSTALLED NEW WIRING AND EXPLAIN HOW TO USE A COUPLE OF VERY HANDY TOOLS TO GET THE JOB DONE RIGHT...WE'RE GETTING CLOSE GUYS...STAY TUNED IT'S JUST GOING TO GET MORE INTENSE FROM HERE ON OUT..!!SpinningwrencheswithJ
Here are the links for the Amazon links for the tools and items used in this video:
RECOIL RCI-26 100% Oxygen Free Copper 6ft 2-Channel RCA Audio Cable, Twisted Pair with Noise Reduction
amzn.to/3DXv0gN
3.5mm Aux Cables, 90° RCA Audio Cable, 3.5mm to 2-Male RCA Stereo Splitter Cable 1/8" Right Angle TRS to RCA Straight Plug Audio Auxiliary Cord,Hi-Fi Sound, Nylon Braided (6.5ft/2m)
amzn.to/3WmWoex
RECOIL RCI66 100% Oxygen Free Copper 6ft 6-Channel RCA Audio Cable, Twisted Pair with Noise Reduction
amzn.to/3WnL8hS
8 Gauge Wire 35 Feet 2 Conductors Power Ground Cable, 8AWG Stranded Flexible Wire for Electrical Wire, Primary Automotive Wire, Battery Cable, Car Audio Speaker, 12 Volt Low Voltage Wiring
amzn.to/4ajE2AZ
Keco 100ft - 1/2 inch PET Expandable Braided Cable Sleeve - Wire Sleeving for Audio Video and Other Home Device Cable Automotive Wire - Black
amzn.to/3PDm6HZ
NAOEVO 18 Gauge Wire 100FT, 2 Conductors Electrical Wire Red Black Cable, Flexible/Low Voltage/PVC 18 AWG Copper Clad Aluminum Extension Cord for Speaker Wire, LED Wire, Automotive Wire 12V/24V DC
amzn.to/3PFFWCh
4 Gauge Wire-10FT Black 4 Gauge Marine Wire + 10FT Red 4 AWG Marine Wire,4 AWG Marine Grade Wire Oxygen-Free Tinned Copper Electrical Wire Cable for Marine Speaker Automotive Boat Lighting Outdoor
amzn.to/40CHjI8
#customtrucks #obsessedgarage #gmc1500 #diy #soundtruck #obstruck #subwoofer #soundsystem #gmc1500 #sierra #loweredtrucks #customupholstery #bagged

[@apquattro]

Good stuff man👍 Clean truck and great attention to detail! Just starting my OBS stereo project as well.

[@SpinningwrencheswithJ]

@@apquattro thank you brother…it’s taking longer than usual but it’s worth it..let me know if you need any help.. I’m here to help you out if I can..!!

[@44thala49]

Love the videos and that truck is slick. I’m hauling my 96 OBS to the painter tomorrow. It’s been a long time coming. Mind giving us your wheel specs? Maker, offset, backspacing, diameter and width? I’m looking for some that will tuck with my 4/6 drop. Thanks.

[@SpinningwrencheswithJ]

Thank you for your comment, this is all the information I know and can share with you about my wheels: American Racing Torque Thrust II Front 20x8.5 +0 offset 4.50 backspacing On 245/25/20 Rear 20x10 +06 offset 5.75 backspacing On 274/45/20 Hope this helps.

[@44thala49]

That is exactly what I’m looking for. I really appreciate you taking the time to post it up. I’m looking forward to seeing more on this truck. I just finished restoring my frame, blasted and coated, new steering, new brakes (keeping the drums for now), new suspension (4/6 drop). I’m lucky, no rust anywhere on the truck so I stripped it of all parts and when it gets back from paint the fun starts. Take care!

[@SpinningwrencheswithJ]

You’re very welcome….This sounds like a great project you got there and I’m sure it will look great when you’re done with it…just be patient and don’t give up..it will take time and lots and lots of money but the end result is worth the effort..let me know if I can help you with anything else…Good luck 🍀

[@rubenflores2870]

Wow, bro, this is a great educational video. You're explaining how to find polarity and also ohms law . It's hard to find a video like this to correctly hook up your back speakers and front speakers plus the doors speakers on the amplifier . I was told to do the back speakers into a 2 ohms and do the front speakers into the 4 ohms for better control for the frequencies, for the amplifier or the EQS of a equalizer. 🤔 don't know what's better.

[@SpinningwrencheswithJ]

@@rubenflores2870 Thank you I appreciate that, as far as ohm loads the higher you go on impedance the cooler and your amp is going to work, also the signal will be cleaner. As far as running the fronts and rears at a different frequency is something that have never done before so I couldn’t tell you brother.

[@rubenflores2870]

So bro, I was thinking, I was going to run my front speakers and my back speakers at 4 Ohms. I have two 6x9 in the back and run my 6 and 1/2 on my 4 channel amp but if I do what you did was Bridge the 4 Ohms into a 2 ohms does that mean I'm going to run my speakers harder than? at a lower ohms, the speakers are going to be louder nice 👍

[@SpinningwrencheswithJ]

@ exactly my man..if you have a 4 channel amp and you install 1-4ohm speaker per channel you can only run 4 speakers off the amp. But if you do what I did in the video you can run 8-4hm speakers in parallel because you will end up with 2ohm load at the amp per channel and you will be louder.

[@andersonteddy]

You’ve lost fader by bridging your front and rear speakers. Those back speakers are gonna scream and you’ll lose any sort of sound quality. With them being 4x6, they will be fine at 4 ohm. You’ll gain so much better sound, using a dsp, by keeping them active on their own separate channels

[@SpinningwrencheswithJ]

You’re correct and thank you for your comment, now that you mention it I will be re-wiring the speakers. I appreciate your input!!

[@andersonteddy]

@ hope it didn’t sound like I was “poo-poo”ing on the video. It’s great and I love the stance and style of that truck. Keep up the great videos.

[@SpinningwrencheswithJ]

@ not at all brother…thank you for your advice and for making me realize that I was making a mistake…🙏🏽

[@robertboyero3797]

What tape are you using to hold down the wiring throughout the floor?

[@SpinningwrencheswithJ]

I’m using 2” pvc pipe wrap, this tape sticks to the sound deadnaming material very well Here’s the link for the tape amzn.to/42DPS72

[@robertboyero3797]

@@SpinningwrencheswithJ Thank you. Can't wait to get updates on the amp boards!

[@bnaudio7813]

Very detailed and clean install. I am confused by a few things, hoping you clear them up. If you are using a dsp. Why 2 ohm bridging per side? Why sub off the radio not the dsp? why epicenter knob as well? They way your wiring it all up, you can't use a dsp except for crossovers which your amp has already. Just confused on whats going on.

[@SpinningwrencheswithJ]

First of all thank you for taking your time to comment on my video, let’s start with your first question , why 2 ohm bridging per side? Because I’m running 8 speakers total from a 4 channel amp, 2-4 ohm speakers from channel that would bring the impedance down to 2 ohm. Why not using DSP to run bass amp? Because my DSP has 2-inputs and 8-channels output, I’m running 2-4 channel amps for mids and hights. Why Epicenter? Because I like to enhance the bass output on songs that require more power. Depends on what kind of music you’re listening to. Personal preference I guess. I hope this clarifies your questions. Thank you.

[@bnaudio7813]

@@SpinningwrencheswithJ Thanks for the response. When you bridge the front right dash speaker and the rear b pillar, you do understand that dsp is almost irrelevant? cant use time correction but more of a crossover. since they are both 4x6's your crossover is more important. Seems like your going for loud and the way you like it. Not hating on you at all. Your work is very detailed and your edits are just as clean. Don't want to see someone waste doolars on what the amp and head unit already does. Keep up the clean, well edited videoes and your detailed installs regardless of my thoughts. Thanks for the response.

[@SpinningwrencheswithJ]

Thanks for your input I appreciate that .!!

[@bnaudio7813]

@@SpinningwrencheswithJ Thanks for the response.

[@richardsanders1884]

I wondered how did you run your fog lights did you find original wiring harness

[@SpinningwrencheswithJ]

My truck did not come with fog lights I installed the valance and lights, I used a 12v fog light wiring harness from Amazon here’s the link: amzn.to/3PSNVMB I hope this helps.!!

[@barrymonroy7138]

You should've put sound deadening on the back pillars

[@SpinningwrencheswithJ]

@@barrymonroy7138 didn’t think about that but thanks for your input, I’ll definitely do that..👍🏼

[@jadsholloway]

Man if I could get my hand on an OBS Chevy…. These are becoming harder to find for the right price

[@SpinningwrencheswithJ]

I hear you, they’re worth it though!

[@barrymonroy7138]

That thing is called a universal joint 😒

[@SpinningwrencheswithJ]

@@barrymonroy7138 got it..thanks 👍🏼