I apologize in advance for the slight fan in the background. It was a very hot couple of days!
Пікірлер: 39
@captainslow471614 күн бұрын
Such a huge help with my new 93z....TY!
@NedacSnosrap13 күн бұрын
Glad I could be of service!🔥
@luiscolon-pg5kc Жыл бұрын
Great content, so much easier doing the timing belt job with engine out of the chassis. Every time I’ve done it is with engine in car.
@NedacSnosrap Жыл бұрын
I did it in car one time and I absolutely do not want to again😅 the z is so low I stretch my knees/back out.
@DwightRollins3 ай бұрын
Good stuff. You were very detailed, which is exactly what I need. Thanks.
@NedacSnosrap3 ай бұрын
Due to my ability to overthink every little single thing I do... Someone has to cover the bases😂 Glad to be of help🙏
@SB-tp3yw7 ай бұрын
About to do this on my UK car, some super useful tips and info, will be watching this while im doing the job! Oh and the engine is staying in 😅
@NedacSnosrap7 ай бұрын
Prepare your lower back for some pain😂 that's about the worst part.
@SB-tp3yw7 ай бұрын
@@NedacSnosrap yeah it’s not great 😂
@c4a05monkey Жыл бұрын
Awesome, looking forward to the second part since I'm planning to do the 120k soon
@NedacSnosrap Жыл бұрын
Waiting on a couple parts I prefer to change and it'll be posted asap🙃
@microevolved7073 Жыл бұрын
Dude I was literally gonna ask you to do this in a past vid lol
@NedacSnosrap Жыл бұрын
Glad to finally deliver! 😎
@erickrivera20568 ай бұрын
Excellent video, a lot of detail. Thank you
@NedacSnosrap7 ай бұрын
You're welcome! 🙏
@fjaime316 Жыл бұрын
Very informative video, definitely learned some new stuff thank you
@alanconnaughton32967 ай бұрын
Ahh man thank you just going to do the 120k on my z very easy follow what you did thanks 💪👍
@NedacSnosrap7 ай бұрын
Just take your time and all will be well!
@mynameisdot93705 ай бұрын
Hey quick question besides from my other comment when u take the belt off and them crank gears move how do I know if it’s still in time or not
@NedacSnosrap5 ай бұрын
If cam gears flop to one side, just correct it by using the dot/mark on the cam gear and the dot on the rear timing cover to get it back in its general area. Those markings are not meant to be exact tdc reference, but to help align your cams to a sitting/resting position to time it.
@BidoBido-dn7py Жыл бұрын
Perfect job man
@trivial1582 Жыл бұрын
Glad I found this, Definitely one of the better guides i’ve found. I’m doing my NA Auto in about a week. Any tips since mine isn’t a manual?
@NedacSnosrap Жыл бұрын
Pulling engine or leaving in car? Only difference i can recall is the protol for removing the crank bolt. I always chalk 2 of my tires front and back when removing the crank pulley vs putting it in 5th and chalking 1. You also have oil cooler lines for the trans going to the lower part of the radiator. Other than that about everything is straight forward.
@trivial1582 Жыл бұрын
@@NedacSnosrap Me and my dad ended up figuring it out. We used a breaker bar on the crank bolt like normal but just wedged a bar to stop the pulley’s from turning.
@andrewscott4405 Жыл бұрын
Great video i could have used this on my last 300Z I redid everything on the front end of the motor lol
@andrewscott4405 Жыл бұрын
I will most likely have to do this to my new 300Z 😬 if the motor is not clapped-out LOL
@NedacSnosrap Жыл бұрын
If you own a z you will likely do it a few times🙂
@PrinceKashez98 ай бұрын
Needed this
@NedacSnosrap8 ай бұрын
Glad to help🙏
@jameszachacz446411 ай бұрын
Nice job!!!
@NedacSnosrap10 ай бұрын
Thank ya🙏
@BlueRB240 Жыл бұрын
Great information.
@mynameisdot93703 ай бұрын
Wat would happen if you spin ur crank without the belt on? Could I just go back to top dead center ?
@NedacSnosrap3 ай бұрын
As long as the cams are in a resting position and the valves are not open, yes. You'll just realign when going to time. Passenger side cams are the ones with valves open at tdc so just flop them over. Also put a long extension in cyl 1 plug hole to verify you're at TDC when you set it back up via the crank sprocket timing mark.
@sloshyelf Жыл бұрын
Oh yessir 🤟
@mynameisdot93705 ай бұрын
HOW YOU TAKE THAT FAN PULLEY OUT LIKE DAH?? NANI??
@mynameisdot93705 ай бұрын
I skipped that part my apologies my friend
@NedacSnosrap5 ай бұрын
No worries😎 Sometimes those fan clutches are seized on badly. Penetrant fluid and some hammer/mallet taps mixed with some prying will get it off everytime!
@mynameisdot93705 ай бұрын
@@NedacSnosraphey also what balancer puller was that I tried getting one but it was too big or sum and also if there’s any other way to pull it out