nissan nv200 spark plugs replacement

[@kidyugi1]

Thank you bud. Had to use this for quick reference didn't know there was a bolt hidden for the throttle body. That were I was stuck on. Other than that video is good. Thank you. Used this at my shop. I approve this video.

[@GrammelVideo]

...never saw any spark plugs coming out or going in within this video... a head scratcher

[@DonCarlos590]

All that to change my spark plugs?

[@aguilanaranjaparada2562]

l never seen whend you remove the spark plug in the entire video

[@user-or2zs8yk3k]

The video was great! I used a 14 mm magnetic socket to get to the spark plugs.

[@PumpkinJack3939]

Perfect video, saw the intake covering the top of the motor and went bruh. But yeah doesn't look too bad at all. Amazing job getting the camera in there with all the angles and views it was great

[@JaboTheMechanic]

Glad it helped

[@aratatarian5161]

Very well done! Quick and concise!

[@HeadlinerMagic]

Good detail video.

[@johndidwhat9464]

Great video but, I would use a shop vac to clean out the intake chambers as opposed to compressed air. It would require a step-down adapter and smaller hose though.

[@upinyaracing1]

you never put the plugs in?????? 14mm or 5/8

[@JaboTheMechanic]

5/8

[@motordar]

Right. Was it taken apart and then just put back together? Did anyone see a plug?

[@RichardKarlson]

My 2013 NV200 has 14mm spark plugs. NGK LKAR6AIX-11. Also... very important, you need a special small narrow socket to fit inside the spark plug hole. My spark plug socket was too large and I had to reassemble the intake manifold without changing the plugs on first try. I was unable to buy it local... special small spark plug socket and had to be shipped in the next day so I had to do the whole procedure all over again.

[@motordar]

@@RichardKarlson thanks for taking the time

[@motordar]

@@RichardKarlson thanks for the info I just bought one

[@jasond3954]

Wow I think they could have designed this better

[@Daniel-pm7np]

Great Job! Take your time, its not that hard. You will need a magnetic wand to get those spark plugs out. Don't forget to gap the plugs. Most are .44. Careful putting plugs back in. TAKE YOUR TIME!!! you're working with and an extended wrench, no need to over muscle those plugs, would not suggest using the air gun on the plugs. Also, if this is your first try, leave the beer in the fridge until the job is complete. :)

[@JohnSmith-id8wv]

So… I have the taxi model, and mine are all seized and stripped. Any idea how to get those out? Been struggling for months.

[@backpackr]

Thanks. I'll be calling my mechanic.

[@thoward4051]

Many thanks for the video. Just what I needed!

[@andrewdailey1837]

Thank you. Used this video in shop.

[@DonCarlos590]

How did you clean the ignition coils? With the compressor? Or dod you relplace them? Also, the number 10 you mentioned coukd be troublesome if not threaded. How do i fluctuate the bolt....wish i had the skill to attempt this.

[@jonjo2136]

This guy just replaced the manifold gaskets! Never saw any plug or even the tool used to remove

[@jkyoft78]

What is the square box that is to the left of the battery, and just after the front air intake? In the video, you removed it to get it out of the way at time 2:24. I opened up that box on my 2021 Nissan NV200 S and it was empty inside, except for what appears to be a round air feed from the bottom. I expected to maybe see some sort of filter inside the box but there is none. It that right? What is the box all about? You have your left hand on it at 14:58 and "don't forget to connect all these". Is it just an air distributor type thing, no filter inside it?

[@jeffs5019]

Dont be blowing air into the open intake ports to get thet crud out, some of those valves are open, you would blow crud right into cylinder.

[@johnkelley4177]

Thanks for sharing the video I have a 2015 city Express needs an engine any videos on the engine swap or advice Thanks John

[@JaboTheMechanic]

No problem anytime time. No I don't. Easiest way looks like you need to take off the front end

[@bryangardner2682]

What's the point we wanted to see what tool is used to remove the plugs ,not how to remove the plenum .The plugs .

[@jesushopeforthenations]

My nissan just started to mis fire and my motor light came on Any suggestions

[@alexmartinez396]

Mine did the same after I change the spark plugs, did you found out the problem , if you did how did you fix it?

[@dennisgreen9823]

what are the torque specs? thanks for making this awesome, helpful video.

[@luisgonzalezjr.977]

great video thanks

[@stephenho6007]

The battery operated wrench tool is great, I have never seen that before, does Harbor Freight carry that?

[@JaboTheMechanic]

The brand is from Milwaukee that can be purchased from homedepot. They have a special on them right now

[@stephenho6007]

@@JaboTheMechanic Is it a 1/4" hex or some 1/4" or 3/8" square? Thank you so much

[@JaboTheMechanic]

No its a 3/8 ratchet

[@MrC6770]

thank you very helpful

[@JaboTheMechanic]

Glad it help

[@clo2884]

Thank you

[@emadayyash9760]

Thank you AAAAA

[@dannygoldbach3243]

Why not replace coils too?

[@JaboTheMechanic]

Because they are working properly

[@freddaniali]

Pain in the a SS job.

[@andysantos8286]

This is not so easy.

[@BobGrosse]

He did all that and he forgot to change the spark plugs!

[@andysantos8286]

So many work, Nissan is horrible to work!

[@mohammadrahman4974]

Can I have your phone number I have same car I need some service for repair change valve gasket