iPad 7 won't turn on - Motherboard Repair- Thermal camera to the Rescue.

  Рет қаралды 60,523

NorthridgeFix

NorthridgeFix

Күн бұрын

Пікірлер
@liverpudd306
@liverpudd306 2 жыл бұрын
Alex, great channel. One almost forgets how miniscule these components are because you make it look so easy. I'm sure that is because of the years of practice you have doing these repairs and building up a knowledge base of likely faults and what to concentrate on without going down rabbit holes! One thing that may be of interest to the viewers is the techniques that Big Boss uses to get into the devices in the first place so that you can get access to the circuit board for repair AND how he puts them back together again "Just like factory". Maybe a couple of videos of that - if Big Boss isn't too camera shy? Once again, great channel, keep up the good work. Alistair
@collectthebread
@collectthebread 2 жыл бұрын
after this video, i cannot imagine just how much waste was thrown away just because of one faulty capacitor. great job
@WKMasterGamer
@WKMasterGamer 2 жыл бұрын
I like it on the end point of the video where you realized you already fixed it and the reaction comes first before the actual reveal. Its so satisfying and heart warming.
@TheReefa24
@TheReefa24 2 жыл бұрын
I'm glad you film this so people can see what goes into repairing a device. the work you've done is worth good money. whether it took 5 mins or 2 hours, it worth the same.
@nirmalkumar7941
@nirmalkumar7941 2 жыл бұрын
After my ipad went for repair coz it won't power on. I started watching ur videos and became more interested in understanding the reason for device failures. Why do iPads always have some problem or other, mostly power on issues. I am disappointed at motherboard quality. Today the technician called and said the processor had shorted in iPad 6th gen.
@zaimsadikovic
@zaimsadikovic 2 жыл бұрын
Did big boss said bismillah before plugging in the charger? Very lovely to see you support him so much☺️
@omermohammed7764
@omermohammed7764 2 жыл бұрын
Yes he did
@sharfazhameed6382
@sharfazhameed6382 2 жыл бұрын
God bless you Alex. You always bring the best out put. You are a roll model for many in this industry. Not only you do great work but follow great ethics.
@alfredperci9262
@alfredperci9262 2 жыл бұрын
Nice video like always Alix thank for sharing everything with us and make them so simple
@MrBiomedical
@MrBiomedical 2 жыл бұрын
You are my motivation to do SMD repairs♥️
@ena6631
@ena6631 2 жыл бұрын
Awesome, I like the use of the isopropyl alcohol as a means of heat detection. Great job.
@stefanitha
@stefanitha 2 жыл бұрын
I'm taking my (almost) daily dose of happiness from you!
@lucymc0191
@lucymc0191 2 жыл бұрын
another great video alex ..... precise and well executed ....even with the priceless thermal camera .... great to see big boss again i feel sorry for him he looks so lonely...you also look tired alex .... have a rest from these videos when you get home editing these great viseos..im sure everyone can wait a week or so ... so you can recharge yourself ...joe uk
@AniDormi
@AniDormi 2 жыл бұрын
I used to come to this channel for the soldering but now I'm here for the fault finding precision.
@whybothertry8642
@whybothertry8642 2 жыл бұрын
Same haha
@justin3594
@justin3594 2 жыл бұрын
Nicely done Alex. I’d love to see you do a few of these thermal diagnostics using the uni-t camera you sell.
@optimizelogicrepair2784
@optimizelogicrepair2784 2 жыл бұрын
He has done a couple
@em0_tion
@em0_tion 2 жыл бұрын
@@optimizelogicrepair2784 No, he hasn't, because he sold them right away - understandable. I'd love to see some fault detection as well, especially with the macro lens, we'll just have to be patient in the current times. ✌
@optimizelogicrepair2784
@optimizelogicrepair2784 2 жыл бұрын
@@em0_tion kzbin.info/www/bejne/d57To5aDa9WHbsU
@Dlehnerswe
@Dlehnerswe 2 жыл бұрын
Awesome technique with the alcohol. Never thought of that! Thank you.
@willmorici5765
@willmorici5765 2 жыл бұрын
Always good to see Big Boss!
@janithmadubhan8273
@janithmadubhan8273 2 жыл бұрын
Hey Alex, could you please halfshort repair video for phones.
@virgildeklerk
@virgildeklerk 2 жыл бұрын
Very Nice fix ones again, i'm sure you would have found it without the thermal camera but it's such a perfect tool for this kind of jobs. Keep up the great video's.
@petermcguiness9514
@petermcguiness9514 2 жыл бұрын
My kids both iPads got took it to a shop it’s meant to fix them in both said mother boards fked in said they can’t be fixed but u just fixed this one ?
@Ahmed_Helmy_AH
@Ahmed_Helmy_AH 2 жыл бұрын
5:25 بسم الله 😍
@unknown4mat584
@unknown4mat584 2 жыл бұрын
I'm glad you guys have more space to work
@imqqmi
@imqqmi 2 жыл бұрын
Very 8nteresting faultfinding! First you identify a problem area with the charger, which seems to check out, then ir camera and an inductor lit up. Inspecting the diode near it showed a short. Then inject voltage at the inductor or diode and another part lights up. One would expect the shorting capacitor to light up too when normally powered, right? Another job well done!
@MathiasVen
@MathiasVen 2 жыл бұрын
That cap also had a notch on the bottom left side 👍👍
@feroztejani1974
@feroztejani1974 2 жыл бұрын
Great job sir Your thermal camera is a wonderful device Nice watching your videos
@freeuyghurspalestinekashmir
@freeuyghurspalestinekashmir 2 жыл бұрын
Big Boss is awesome! ❤️‍🔥
@vinkuu
@vinkuu 2 жыл бұрын
The economics of repair is astonishing. Replace one faulty cap that costs mere fractions of a cent to manufacture vs. building a new device.
@johny1220
@johny1220 2 жыл бұрын
Wow, was just on your channel looking for videos to watch then bam! I got the notification for this 😂
@kpelectronics
@kpelectronics 2 жыл бұрын
That thermal cam is magic.
@herbcraw1804
@herbcraw1804 2 жыл бұрын
Great job as usual Alex
@tecnologialm6994
@tecnologialm6994 2 жыл бұрын
hola estaria muy bueno q hagas alguna reparacion con analisis de schematic desde ya el canal es excelente muy bueno saludos desde argentina
@EatSleepLiiV
@EatSleepLiiV 2 жыл бұрын
NorthridgeFix micro soldering Zoom call COURSES? BE fire to learn how to do this myself from a legend....
@stefanlechner
@stefanlechner 2 жыл бұрын
Very nice video, i love it. Awesome work, good and efficient repair. Thank you for that video. Greets
@donnang8763
@donnang8763 Жыл бұрын
Which coil did you inject the voltage to?
@adnansami8594
@adnansami8594 2 жыл бұрын
Excellent very good work 👍👍
@jdeltoro518
@jdeltoro518 2 жыл бұрын
The thermal is great troubleshooting tool
@pedropessoa594
@pedropessoa594 2 жыл бұрын
Very nice. I have the same problem on my iPad 7 th. Is it expensive repair to the client? Thanks for the video
@susperia1188
@susperia1188 2 жыл бұрын
Would it have been possible to use the hot tweezers instead of hot air?
@Oneklickmedia
@Oneklickmedia Жыл бұрын
So my son iPad randomly stop charging when he woke up. Tried home and power reset with nothing. Plug it in mac and it detects to do an iPad restore but fails. Guessing there no power? Do I trouble shoot: check LCD/back light, Check Battery, and then check for short like you did here? Also iPad 7th gen
@basomiddin
@basomiddin 2 жыл бұрын
Where is your workshop situated. It's very interesting for me. Is there Turkey?
@nibz7255
@nibz7255 2 жыл бұрын
Salam from New Jersey Alex.. my ipad 7th gen is exhibiting same issue after powering off and never coming back or taking charge ... hypothetically if same repair would it be cost effective to repair? Not sure what this repair may cost.. thank you for your time and J.A.K
@nameless780
@nameless780 2 жыл бұрын
What about hard drive with clicking sound? Is it done ?
@ryt-is
@ryt-is 2 жыл бұрын
This probably has been asked a million times before, but how do you determine the replacement cap values?
@-eMpTy-
@-eMpTy- 2 жыл бұрын
You can measure capacitance with most multimeters (cap has to be desoldered). For the voltage, it doesn't really matter if you use one with a higher voltage rating, just shouldn't be lower. Other than that, just get X5R, these are the most commonly used ones.
@mattagren
@mattagren 11 ай бұрын
My Ipad died, but I was able to boot it up twice, then it died again. And now it's completely dead, could it be the same problem you just fixed?
@vicktorcyprus21
@vicktorcyprus21 2 жыл бұрын
How much voltage u apply on the coil
@PUBGMOBILEBAN-m9e
@PUBGMOBILEBAN-m9e 2 жыл бұрын
What is the name of the cleaning material?
@carlomac2640
@carlomac2640 2 жыл бұрын
Hi Alex! Why are you not using the UniT thermal camera anymore? Thought it was better than your old one?
@arasus6107
@arasus6107 2 жыл бұрын
Awesome job bro keep rocking bro 👍👍👍
@tecnogof
@tecnogof 2 жыл бұрын
Can I get a link to the full outro tune purrleeeeze ? Asked a few times, all i get are spam replies!
@Taveira82
@Taveira82 2 жыл бұрын
Great Alex once more
@mohamedhussein120
@mohamedhussein120 2 жыл бұрын
Very nice. Keep it up 👍🏾
@AKhan-nu9mw
@AKhan-nu9mw Жыл бұрын
Very good. Sir. Thanks
@anecuareformas
@anecuareformas 2 жыл бұрын
Eres lo máximo, gracias amigo , saludos …
@plakic
@plakic 2 жыл бұрын
How do you go about troubleshooting a board that is freezing? What components can cause this problem?
@LaNiveladora
@LaNiveladora 2 жыл бұрын
I know the big boss must be busy, but it would be nice to see videos on how to disarm and arm devices. just say!
@Unsocial200
@Unsocial200 2 жыл бұрын
Does anyone know how you choose the proper replacement for a bad capacitor?
@rfr653
@rfr653 2 жыл бұрын
good job mate.
@Druid4026
@Druid4026 2 жыл бұрын
alex what so funny the you laugh at the end?
@bezolsmate
@bezolsmate 2 жыл бұрын
I can't stop watching these videos man it's like crack
@peterh7575
@peterh7575 2 жыл бұрын
awesome! PS: possible to have done that repair without a hot air gun but with just a soldering iron?
@ktingmar
@ktingmar 2 жыл бұрын
Yeah, with low melt solder. But hot air is usually way faster and easier.
@Darren777Au
@Darren777Au 2 жыл бұрын
Nice work.
@mikeanderson1994
@mikeanderson1994 2 жыл бұрын
First comment amazing video's as always keep up the good work brother!
@prasannaattanayaka3931
@prasannaattanayaka3931 2 жыл бұрын
Hi sir...i am your big fan
@achimugusolomon8563
@achimugusolomon8563 2 жыл бұрын
weldone Alex.
@touristthor
@touristthor 2 жыл бұрын
how much is that fix
@ronlevin2339
@ronlevin2339 2 жыл бұрын
You can see immediately that it is a left cap,. it is broken near the solder
@tawnyb83
@tawnyb83 2 жыл бұрын
great job
@hadjsaidahmed3144
@hadjsaidahmed3144 2 жыл бұрын
Thank you خال
@mattagren
@mattagren 11 ай бұрын
That is crazy!!! 💕
@ezzeldin101
@ezzeldin101 2 жыл бұрын
Big boss is the Best
@pullutshop8572
@pullutshop8572 2 жыл бұрын
Thanks for repeat that problem. Ok
@alialshams1043
@alialshams1043 2 жыл бұрын
nice Vedio ☮️ 👍
@anandk8328
@anandk8328 2 жыл бұрын
Hiw do you what type of capacitor with specifications should be replaced?
@anandk8328
@anandk8328 2 жыл бұрын
There is no etching on the motherboard for values of notation.
@em0_tion
@em0_tion 2 жыл бұрын
Schematics or just donor board.
@nelchan2421
@nelchan2421 2 жыл бұрын
Good Job
@sidgaming0078
@sidgaming0078 2 жыл бұрын
Yesterday my ipad 6th gen randomly turns off and won’t turn or what was the problems
@anandk8328
@anandk8328 2 жыл бұрын
Dude you are amazing
@suryavanshib
@suryavanshib 2 жыл бұрын
Awesome ✌🏻✌🏻✌🏻
@protection4541
@protection4541 2 жыл бұрын
tanks
@kabandajamir9844
@kabandajamir9844 2 жыл бұрын
So nice
@ZeroBitMatera
@ZeroBitMatera 2 жыл бұрын
mi aspettavo un ...ta da!!!! :-))) bravissimo!
@rajannarayanan2759
@rajannarayanan2759 2 жыл бұрын
Very good Thanku
@balakumar9836
@balakumar9836 2 жыл бұрын
Super 👍
@protection4541
@protection4541 2 жыл бұрын
Hi Engineer. How did you find out that this is a capacitor? You first had an EC connection. How did you suspect this area?
@TheThore
@TheThore 2 жыл бұрын
If something is shorted to ground, like the diode, anything connected to it can also be the defective component. He injected voltage to the diode and looked under the thermal cam where a heatspot emerges. This was the area of the three caps. Then he applied iso pronanol onto the caps and injected voltage again, the cap where the alcohol is dried first, is the hottest cap, so at high possibility the defective cap. Nice way to track it down. Without thermal cam you have to test each cap.
@chethankiran5478
@chethankiran5478 2 жыл бұрын
Boss 😍😍😍🤗🤗🤗
@emadab5433
@emadab5433 2 жыл бұрын
You are awesome
@ashrafkarjiker6888
@ashrafkarjiker6888 2 жыл бұрын
Make videos with schematic which can be more to learn
@sanjayraina2789
@sanjayraina2789 2 жыл бұрын
Hi, I really like your videos and learned a lot about repairs and highly appreciate your videos. I have an apple Tablet that requires repair for wifi issue ( the chip was removed by some unprofessional technician and have damaged the some of the tracks on the motherboard as well as on wifi chip 😭) and now he broke the display also and replaced with another one but now only half display doesn't work for touch. I finally took back the tablet from him and decided to send it to you as i am confident and sure enough that you can make it up and running for me. I can't mail the device to you from India as it cost me very heavy , so one my friend is visiting USA by mid of March for limited period of time, and I am sending the device with him to you, but I am not sure how he be placed in USA so will you please please please help me and guide me how to reach you there and handover this apple tablet to you. Quick response is very highly appreciated. Thanks
@sanjayraina2789
@sanjayraina2789 2 жыл бұрын
PS: "correction - how he will be placed in USA"
@navidmessof5291
@navidmessof5291 2 жыл бұрын
nice
@kswappedem2
@kswappedem2 2 жыл бұрын
I have a dell g7 17 7790 that charges when it feels like. And turns itself on when it gets power. Whether the lid is up or down. Paid 1800 for it and it broke as soon as the warranty finished. Pos dell
@em0_tion
@em0_tion 2 жыл бұрын
Shit happens, just get it to a trusted local shop.
@WeSoldOurLives
@WeSoldOurLives 2 жыл бұрын
Better than factory!
@clairenapolitano6116
@clairenapolitano6116 2 жыл бұрын
How is your backlog going? Did you end up employing anyone?
@shubhamsahuSD
@shubhamsahuSD 2 жыл бұрын
5:22 Big boss.Big boss,sss.... Big boss.. Thank you big boss
@KingKing-tz6of
@KingKing-tz6of 2 жыл бұрын
Big boss
@qewadszcx11
@qewadszcx11 2 жыл бұрын
That was fast!
@zaidmj9173
@zaidmj9173 2 жыл бұрын
👍👍👍
@ukaszs5021
@ukaszs5021 2 жыл бұрын
👍
@pointer2null
@pointer2null 2 жыл бұрын
Two questions: You always call him "Big Boss"... is he the Boss? Where did you lear 'electronics', self-taught or Uni?
@jorgevazquez7950
@jorgevazquez7950 2 жыл бұрын
Can you find the problem to my overheating gaming laptop if so ...send me a number or address!
@RR-fv2uu
@RR-fv2uu 2 жыл бұрын
we only wanna see hiroshimas
@abdalothmab9632
@abdalothmab9632 2 жыл бұрын
i think apple should make contract with u 😜 send to apple for information
@bestbuildpc
@bestbuildpc 2 жыл бұрын
Those capacitors are garbage! quality from capacitors are down.
@rockstar-kp2jy
@rockstar-kp2jy 2 жыл бұрын
Cpu
@shamsalfaisal
@shamsalfaisal 2 жыл бұрын
Came in for no power
iPad Logic Board Power Dead Repair 【Tutorial】
24:45
iPhone Service Malaysia
Рет қаралды 69 М.
HP Laptop Repair - No power Caused by an Awkward Button Design.
9:20
BAYGUYSTAN | 1 СЕРИЯ | bayGUYS
36:55
bayGUYS
Рет қаралды 1,9 МЛН
Правильный подход к детям
00:18
Beatrise
Рет қаралды 11 МЛН
Mini PC Damaged SD Reader Failed Prior Repair. Is it Fixable?
15:54
NorthridgeFix
Рет қаралды 38 М.
iPAD 7th Gen A2197 no power fixed
9:15
SOSfix Electronics
Рет қаралды 28 М.
DEAD ASUS Laptop Repair
8:16
NorthridgeFix
Рет қаралды 33 М.
Heavy Zebra 410 Repair - Damaged USB and more issues.
14:51
NorthridgeFix
Рет қаралды 36 М.
Dead Benz Key Fob Unexpected Fix
14:15
NorthridgeFix
Рет қаралды 27 М.
How we Fixed a Dead 2020 M1 Apple Mac mini
10:35
NorthridgeFix
Рет қаралды 40 М.
EVGA 3090 FTW3 Not Detected - This one is weird.
17:41
NorthridgeFix
Рет қаралды 42 М.