SSG10 Spring Change Guide

[@elek7rix391]

Thank you for the tutorial I didn't wanted to break something on my Gun

[@funky4247]

Thank you very much novritsch 👌😁

[@cjchiong1391]

@Novritsch can you make a video for orange end cap removal?

[@cooperpatton1513]

When are you going to restock your store for the USA

[@patrikdarre5572]

hi i accidently destroyed the thread on the outerbarrel and in the receiver even tho i didn't over thight it. i just screwed it in and since there wasn't any resistance i took it back out and saw that thew thread was gone. is this a common problem, and is it something the warranty are gonna cover?

[@QuartzGhost.]

the cylinder head on the gun is hellbent on staying there and will not budge any advice?

[@xcontrol3741]

I’m gonna be ordering the SSG10 A1 450fps version because you guys are out of stock of the 500fps version for the USA warehouse. And I’m in the USA. And I can’t wait another month to get one and play with it. So I’m ordering a m170 spring. I’m afraid it’s gonna give me problems or not perform precisely and auccuratly after I change the spring. I’m afraid it’s gonna act up and give me problems after I change the spring

[@lopiutz2893]

ok

[@NepaAirsoft]

Should you re-lube on the change?

[@novritsch-teching]

There should always be some little bit lube on the springs.

[@justheart3369]

Thank you Christoph

[@murderouspillowgaming9001]

I cannot get this outer barrel in line when I screw it back on. Every time I screw it back on no matter where I start it always ends up with a Hop up at where the scope would be.

[@alvaroaugustomeridio]

Hi, can this be fitted in an ssr77? 1 joule is too low and 1,4 joule is to high for Spanish regulations

[@snensjoost9027]

do you need this glue for the screw or is it possible without it?

[@novritsch-teching]

having screw glue is always a good idea. You need it all the time.

[@snensjoost9027]

@@novritsch-teching ok, thank you for the quick response.

[@jooosh335_4]

At 7:45 is it normal that my ssg10 has no glidering ??? My ssg10 has only the Front glidering gen2

[@wadef5065]

I got .46 for my a1, idk if my hop up is broken cuase the bullet only goes down, or if my springs not strong enough to push a 46

[@WitchDoctor87]

Crap well hope that not $300 gone... I've no idea what happen but my gun is no longer working. I never even got to play with it. I pulled the bolt and that seems to be working properly. However the barrel doesn't go on properly. I made sure to have the bolt half cocked so I don't screw my bucking. However putting the barrel on the gun seems to not want to fire properly.the outer barrel is extremely hard to put back on and upon taking it off I did noticed the spot where the screw goes to hold the outer barrel on looks kinda jacked up. I might have found the issue, the black ring if you put it in the wrong direction it can mess everything up. The issue with the screw that holds the barrel was pretty jacked up though. I will be using it for the first time tomorrow. Hope it proforms as many videos have shown.

[@infamousdrsteve9324]

Should probably mention that when I unscrewed the outer barrel the plastic/rubber ring that sits just inside came out with it but in multiple pieces... How much of an issue is this?

[@christophhaas5696]

Oh thats not good. Please dont shoot like this. Your gun can really get damaged.

[@xcontrol3741]

I’m afraid I’ll screw up something while in the process of changing the spring, therefor making it inconsistent and inaccurate. I’m confident I can do the change tho

[@wasted3250]

How did it go?

[@xxs1lentk1ller30]

U cant fuck anything with only spring change

[@alexgroezinger762]

How much FPS wil you have if you have the m150 spring and all the spacers rings?

[@Sledge762]

I can’t unscrew the barrel after I removed the Felix screw

[@SvenskaInvesterare]

Got from 2.5j to 2.75j in 100 shoots made! M160 and all shims(spacers) 2,4,6mm spring and factory New. Still not 2.9 i wanted😅 should i try m170 without spacer or will it still break 3j? 0.40-0.43g Bbs

[@christophhaas5696]

Yes try it. If it is to strong then put in one of the 4 air break pins. They are making your gun quieter while reducing some fps.

[@magnumopus1628]

@@christophhaas5696 4 break pins? What are they?

[@O38.289]

Do i have to get new parts to exchange the spring

[@steammausss164]

What is the dimensions of the spring?

[@urimandthummim5780]

I am told that I can change the spring by opening the rear of bolt without removing the furniture, which is supposed to be the right way between game play. Am I right?Your way seems to be too much disassembly

[@mateitirsu.p.1124]

How are you supposed to remove the rear part of the bolt, that is rivetted in and you have no access. Whoever told you about accessing the spring fron the back was referring to aegs that have that option, and in no way to sniper replicas that need to have realy sturdy back components to keep the spring guide pressure and bolt pull pressure. This is the easyest way, you can also go the hard way and take the full bolt out

[@patrikdarre5572]

Do a video om receiver change

[@richisong95]

When are the generation 2 glide rings going to come out? The stock glide ring causes the piston cylinder to wobble a bit, which in turn affects how the cylinder head enters the hopup unit. Please answer this question as it is a crucial element that will affect the longevity of the ssg10's internal parts.

[@novritsch-teching]

The gen2 glide rings got delayed because of the virus. If you contact the service team, they can give you more infos on when they will arrive.

[@nicholasdial5041]

Hey, I just got a new sniper and it consistently curves far left. Do you have any information about how I might be able to fix that?

[@kimjongthicc95]

Nicholas Dial did you clean out the gun after you got it? Sometimes the barrel of airsoft guns could not shoot right because of the manufacturing process, and some oils might have gotten in the barrel making it shoot weird. I say try cleaning the inside of the barrel and making sure the components are tight and on right.

[@xxs1lentk1ller30]

@@kimjongthicc95 nortfish

[@thegascore2408]

Novritsch question about the ssp1 can I put a hi capa slide on my ssp1

[@danilopg32]

I cant remove barrel i tried so hard... dont know where is the problem

[@Grimhead]

At 4.30 when I pull the bolt all the way back I do not get a klick. Aslo, I can't remove the spring guide. It stays inside, wobbling around. I have the A1 model. Anyone know why that does not happen for me?

[@beeje1309]

I noticed that my spring guide didn't come out easily - I ended up having to rack it back really hard. And then when I put it back together I can only get one shot and then it won't hold. I think it might be something to do with the piston sear

[@airsoftentertainment1166]

Nice video

[@daburg8692]

I am having problems with the ssp1 as when I take the mag out the slide get very sensitive as when i give the ssp1 a nudge it lock forward suddenly.

[@NL-hw4kg]

Just so you guys know. When adding rings the rifle might not fire anymore if thats the case you need to remove a couple rings. Mine only took the 4mm ring if i added more the rifle would not cock anymore.

[@am3440]

Does anybody know if this tutorial works the same for the ssg96?

[@O38.289]

Umm can i change the m170 spring to vsr-10 the same way as the ssg 10 can you please tag me so i can see the answer i really need the information. And do i have to remove the spacers from the inside

[@mateitirsu.p.1124]

No you cant, the inner diameter is bigger then the standard springs, it wont fit in the guide

[@ManUpOnlyForMan]

Which spring do i have to choose for 2,30 joules

[@lopiutz2893]

eu.novritsch.com/product/ssg-spring/ scroll down and youll see a chart.. M150 (light BB's) or the M160 (heavy BB's)... i would choose the 150 .. thats definitly not more than 2.3 joules

[@ManUpOnlyForMan]

@@lopiutz2893 whats your field limit?

[@XcylLencioco]

I don’t have any airsoft gun and im watching this lol 😂

[@mdag1383]

Me too. Where are you from?

[@XcylLencioco]

@@mdag1383 im from Philippines 🇵🇭 also im 12 years old and I really like those guns

[@mdag1383]

@@XcylLencioco did Philippines allow airsoft? I'm from Malaysia. I'm 13. Malaysia don't allowed airsoft

Can you teach us how to replace the outer barrel on ssp1

[@xxs1lentk1ller30]

Bruh

[@islands146]

What lube

[@maxibichler7927]

Weiß jemand ob die Teile von der ASG m40a3 in body von der A2 passen?

[@bluehernandez3594]

I got a question, what spring recommendations would you suggest for the s&t ppsh-41 for indoor fields that have a maximum fps of 400?

[@valtteri2993]

I would go for m110

[@maxiilien116]

if i want 450 max u advice me which spring

[@patrickcooper7373]

I would advise the M130 spring with adjuster rings, you could try to get a M140 but there is a chance that it might exceed the FPS limit in your field

[@christophhaas5696]

Try m140. If it is to high put in one of the 4 air break pins. They make your gun quieter while reducing some fps.

[@fazeryder3105]

@@christophhaas5696 with m140 i hav 487 fps 2.2 joules

[@callsigndagger7016]

would this work for any vsr 10?

[@nickaldrichairsoft6770]

If your talking about the springs then Yeah it should the ssg 10 is compatible with the Tokyo Marui Vsr 10 but there can be compatibility issues with tm clones.

[@Paaaluch]

which spring will be the best to get 600fps max? now I have 2.8J 500fps... H

[@Reaper-it8ru]

Palu ch buy a 170 spring and if its lower than 600 fps, buy the fps adjuster rings :)

[@christophhaas5696]

And if it is to high then, put in one of the 4 air break pins. They make your gun quieter while reducing some fps.

[@nickaldrichairsoft6770]

I put a sp 190 spring in my ssg 10 A2. The bolt is pretty hard to pull back but my main issue is that the bolt doesn’t feel as smooth as it did with the stock spring. Does anyone know if over time it will feel smoother and if not how can I make it smoother? also if I should continue using that powerful of a spring I don’t want to damage the gun even though it should handle springs like this

[@treidbate2619]

yea my spring did feel way smoother over time

[@44scream]

I have the same problem now,after 11months how is it now by you?

[@xxs1lentk1ller30]

Cuz its 7mm spring?

[@dorfkind9825]

The spring will not damage anything it's not like with aeg where the gears or the shell could be damaged. Even on novritschs site you can buy up to 220mm springs

[@thibautgekiere9946]

I have a problem, the spring and spring guide make a rattling noise. Does somebody else have this same problem?

[@sammcool1953]

Hiya. With adjuster rings. How much fps on average do each one add to fps. Thanks

[@lqxd6218]

why is my gun so hard to pull back

[@pilot20]

It's the springs power or no lube on it

[@slavlife505]

Can this sprig be used in a Aeg?

[@xxs1lentk1ller30]

Nah

[@lil_shrimp]

Ich warte immernoch auf meine ssg10😂😥👌

[@christophhaas5696]

Angekommen?

[@lil_shrimp]

Ja beste waffe die ich je geschossen hab🥴

[@octobanipus4524]

Hast du zufällig diese Ringe?

[@joniisdaaa7916]

Hi was geht

[@phyl47]

Hi novritsch can you please make a "how does a gas blowback airsoft pistol work" video?

[@synops.fu2e]

Not that hard but we will see if i broke something doing this

[@stefangjorgjievski]

Please add shipping to North Macedonia