Nut and Bolt Assembly design with Animation | Part design with custom thread in Creo Parametric

Nut and Bolt Assembly with Animation in Creo Parametric.
This video will guide you through designing a nut and bolt, assembling it using mechanism constraints, and demonstrating the mechanism design in Creo Parametric. You will learn about part design, assembly design, and mechanism design related to nut and bolt in Creo Parametric. So let's get started.
Join this channel to get access to perks:
/ @cadxtraining
Playlist:
• Part Design in Creo Pa...
• Complex part design in...
• Sheet metal tutorials ...
• Surfacing in Creo Para...
• Plastic Design in Creo...
• Assembly Design in Cre...
• Detailing the drawing ...
• Gear design in Creo Pa...
@CADxTraining #CADxTraining #CADx
/ @cadxtraining
/ cadxtraining
t.me/CADxTraining

[@ii_neo_ii9148]

Your explanation is so clear, which understand your video much easier. pls make more video like this . GOD BLESS U.

[@arkaaldov5893]

Beautiful thank you! Keep them spinning!

[@swapnil8854]

I watch fulll advertising only for supporting you🙏🙏🙏

[@kirankumarlingegowda5223]

Hello Satyendra, I learnt Creo just by watching your videos. Thank you very much for uploading these videos. I need to add thread dimensions in the family table. (for bolts and nuts). I tried several times, but did not succeeded. Can you please make a video on this.

[@vikassinha9557]

Thank you sir Next request for Geneva mechanism with calculations

[@shubhamkumawat8876]

Sir, plzz make a Gd&t series. I love your teaching technique and it is amazing

[@swapnil8854]

Thanks sir for uploading such a good model

[@bhaskersharma4879]

Thank you

[@neel9567]

Sir when i am making hole of M10 size its diameter is showing 0.3543 in creo9.0.0.0

[@dipakbhalekar9419]

Thank you for the tutorial sir.It was very helpful.Can you please make one overview tutorial on dynamic constraint,connection and mechanism.

[@avinashm5416]

❤ thanks

[@vipinv.p3782]

your tutorial so valuable to understand much more about Creo, you are detailing each minute things very appreciatable Thank you so much Sir. I have a doubt coulf you please rectify..? What's the difference bet: datum centreline among sketch centreline..

[@arkaaldov5893]

Hello Satyendra! I hope all is well, waiting on a new video! Thanks and best wishes!

[@praveenkowju5641]

thanks for the video bro. please upload videos on molds module..

[@rajeshroyal5922]

Sir, please Make tutorials on Animation and Mechanisms

[@msk8284]

Agree

[@zameelkns]

Pls make more video about mechanism.

[@akshaypatil5701]

Sir in vedio at 21:15 ...there is pitch circle diameter to add..9.75 mm. But in my software which is 5.0 i m using There is option that is icon location.. I m not able to add diameter ...value...

[@GoodPipel123]

same with me.... did you find the solution bro?

[@CADxTraining]

Check the motion symbol selection

[@GoodPipel123]

thank you sir@@CADxTraining

[@zameelkns]

Pls upload a video about how to create A3 sheet layout and BOM...

[@techinhemanth1246]

Please tell how to set Start and end point thread of bolt and nut sett

[@vvvipin1]

hai sir. i followed the same steps as you did. but even though I applied the cylindrical motion there is no movement for the nut or any movement for the assembly. why is it like that sir? any suggestions

[@sourabhdhumal8126]

Sir aapne H value or nut ke length 26 mm kaisi nikali tutorial me kaha mention ki hai plz reply me i m confused about it

[@CADxTraining]

Please mention the time stamp from the video

[@sourabhdhumal8126]

​@@CADxTrainingsir whole video dimensions confusion

[@CADxTraining]

All the time calculated based on M10 nut and bolt. You have all the formulas in the drawing placed on the left side in the video.

[@ranjubala5732]

How can we use hatch colour from the 3D part in assembly drawing?

[@ganeshshiva4116]

Hello sir the regenerate option is also not working hole is can't able to create only in small size😢

[@kunalverma2323]

Sir if I want to use a bolt for mounting a body with base then which constraint is use?And how it's animated?

[@paultello1042]

Why save the file and then open it again in a new tab?

[@CADxTraining]

Write the timing from the video.

[@xyz._.1234]

How to enable cabling tool in creo?

[@CADxTraining]

Open your assembly file first. Then go to application and cabling.

[@ravibits90]

Sir, Aap one video Unf TPI thread ke uper banaye, mujhe unf tpi ka calculations smjh me nhi aa rha he

[@musmanqureshi5354]

Sir in the start of video, from which book have you taken drawings of nut and bolt

[@CADxTraining]

Drawing book from Gopalkrishna

[@solidkreate5007]

How did you know to use ∠75° and 0.500mm when you extended the helical cut transition thru?

[@CADxTraining]

70 to 75° is the industry practice.

[@solidkreate5007]

@@CADxTraining will that angle work for me in ASME? Is there a Standard I can look up?

[@CADxTraining]

This is a general practice. I am not sure whether it comes under ASME. Thread is something, no body design. Thread manufacturing is a standard process.

[@RamanHeer818]

@@solidkreate5007 sir how thread height is 0.5 mm

[@omkarsutar578]

😵 Beginner 🥵

[@sudheersirimane5755]

How to change , to . ? Sir in dimension

[@CADxTraining]

Your question is not clear.

[@sudheersirimane5755]

@@CADxTraining While iam giving thread dimensions it's showing 12,00 instead of 12.00

[@ajith6842]

Hi sri, please explain creo Stl file format

[@ankitdamke8765]

Snapshot is not turning on

[@CADxTraining]

Try it one more time

[@ankitdamke8765]

I tried multiple times

[@pds19k86]

Hi how to contact you??? I have some professional work to be discussed.

[@TechWayTamil]

Sir Please share your maid id I will send some part model kindle to make that design.

[@CADxTraining]

[e-mail]

[@akshaysarwade9543]

Hello sir, Please make new videos

[@CADxTraining]

It's on the way.

[@akshaysarwade9543]

@@CADxTraining thanks sir

[@maharajank1468]

Thank you