NV3550 Rebuild

  Рет қаралды 6,624

Auguste88

Auguste88

Күн бұрын

Пікірлер: 14
@bryangardner4370
@bryangardner4370 2 ай бұрын
great job, so little information for DIY guys, check for parts before you tear down (some are no longer available...ANYWHERE) use a rubber band on the hidden bearings for reassembly,
@kit.30
@kit.30 Жыл бұрын
beautiful camerawork on this one 👍
@Auguste88
@Auguste88 Жыл бұрын
Thank you!
@danisibaja
@danisibaja 10 ай бұрын
How do you replace the bearing behind the output shaft seal (16:32 min)? You can do it the same way you replace the output shaft seal?
@Auguste88
@Auguste88 10 ай бұрын
No you would need to knock it out with a punch or a bearing sledge. I have yet to pull mine out, my other transmission is good so far. Good luck!
@danisibaja
@danisibaja 10 ай бұрын
@@Auguste88 Thanks, a bad bearing like the one un your video can cause an oil leak? I replaced the output Shaft seal on my Jeep but it's still leaking oil and I punch the bearing cap with a screwdriver so I'm thinking that can be the problem
@Auguste88
@Auguste88 10 ай бұрын
@@danisibaja that could be hard to say. Although the cap on the bearing is there to retain oil against the balls to protect and limit friction. Not sure to what extent a puncture in the cap would factor in your leak problem. I would change it. Don't forget you need to apply liquid gasket on that cover as well.
@danisibaja
@danisibaja 10 ай бұрын
@@Auguste88 ok, thank you for your help and time!
@johnlatham6382
@johnlatham6382 Жыл бұрын
Well done. Do you know of any way to get the reverse idler support bolt back in while it still mounted. I thought I was pulling out the fill plug.
@Auguste88
@Auguste88 Жыл бұрын
Mine just screw back in. The support treaded hole need to line up with the case hole and it should screw right in. If the transmission is still all together I would try to line it up with a screw driver and a flashlight. If it's an option it might be easier with that side facing up. Good luck!
@johnlatham6382
@johnlatham6382 Жыл бұрын
@Auguste88 Got it, used 2 small flat heads to walk it into position in the bolt hole. then some wire to hold it position and then treaded the bolt and pulled the wire at the same time. It was a pain but so happy I didn't have to drop the transmission.
@Jeepm0de01
@Jeepm0de01 Жыл бұрын
Thanks for sharing. Looking to tackle this over the next couple weeks 👍
@martinpena7587
@martinpena7587 5 ай бұрын
Where I can get book rebuild transmission nv3500
@Auguste88
@Auguste88 5 ай бұрын
@@martinpena7587 Jeep TJ maintenance manual
Manual Transmission Operation
24:04
WeberAuto
Рет қаралды 10 МЛН
NV3550 Rebuild
39:08
Curmudgeon Transmission
Рет қаралды 1,6 М.
Beat Ronaldo, Win $1,000,000
22:45
MrBeast
Рет қаралды 158 МЛН
Try this prank with your friends 😂 @karina-kola
00:18
Andrey Grechka
Рет қаралды 9 МЛН
1933 Plymouth steering column installation.  Episode 2 of 2.
1:18:14
Dale Kraemer's Custom cars and anything
Рет қаралды 4
NV3500 Transmission Rebuild Tips (no jig)
6:21
n3spitzkopf
Рет қаралды 18 М.
Gears scraping and popping out  01 Jeep Wrangler NV3550 5sp
6:57
Transmissions America (John and Eddie)
Рет қаралды 4,6 М.
1997 Chevy Blazer: NV3500 transmission disassembly
28:23
⚠️DANGER DOBERMAN⚠️
Рет қаралды 2,2 М.
NV3550 to AX15 Jeep Transmission Swap
20:38
THE ASAP AUTOMOTIVE CHANNEL
Рет қаралды 15 М.
NV4500 transmission question answered
8:26
Bobby B
Рет қаралды 10 М.
Why you SHOULD rebuild your own manual transmission in your project car!
13:13
Please DO NOT Buy a Jeep (Unless It Has This Engine)
10:04
Scotty Kilmer
Рет қаралды 590 М.
NV3500 standard transmission rebuild how to -part2
15:00
valflyinf
Рет қаралды 65 М.
NV3550 Disassembly
23:08
Curmudgeon Transmission
Рет қаралды 1,3 М.
Ремонт BMW 535i GT молотком и зубилом!
52:57
ИЛЬДАР АВТО-ПОДБОР
Рет қаралды 2,5 МЛН
Лада ОКА против BMW 646i
0:26
AutoHot
Рет қаралды 165 М.
Màn cứu hộ xe xúc lật cực căng #shorts
0:52
Nghia Plaza TV
Рет қаралды 3,5 МЛН
VIP ГАЗель ЧТО ВНУТРИ????!!!
0:45
Автомобильная История
Рет қаралды 6 МЛН