Making my homemade steam generator SAFER!

[@nado121]

Always glad to see another one of your videos. I loved that you took the time to do calculations on the efficiency of your setup. Have you thought about SLIGHTLY pressurising your tank by passing the steam through a water column before it exits the system? I'm curious if that could help shorten the runtime.

[@danielsigursson8512]

Thank you for showing that level switch. I will add one to my sterilizer barrel.

[@vicekwad8537]

Fantastic, The new insulation looks a lot nicer now but can you stick a bit of silver tape around the PIR board under the weight. Might as well make it 100%. 🤙

[@filippoostuni3251]

Hello mr TOM do you have any video about the Chinese sterilizer you have bought months ago, ??? Best regards

[@DeepMindfulness]

Would this work for a diy steam room? And is there an attachment that fills the tank when it’s too empty? It would be great if, like a toilet, it had a device that caused water to fill it when it was too low…

[@neogeo8267]

Citric acid to remove scale. Works brilliantly

[@plasmapanasonic4741]

Pee in it?

[@neogeo8267]

@@plasmapanasonic4741 that might work, but wrong kind of acid. Citric acid can be had for cheap in bulk off amazon and similar. Works awesome for cleaning up scale and making fizzy drinks taste tart.

[@OakandSpore]

Need to squeeze some lemons into it!

[@lowcountryfungi]

"Yolo" had me in tears haha

[@maplebrookmushroomco]

I would like to buy your plan. Brilliant!

[@mattbartels4598]

I have just found you Chanel, Mate I love your work I'm now about to start from the start of your videos keep pumping out the great content brother!!

[@OakandSpore]

Welcome aboard bro! And thanks for the support. Hopefully you can learn something from my mistakes :D

[@mattbartels4598]

@@OakandSpore i sure have already im about to buy and get built the new steam generator and get 2 200lt stainless steel barrels made up or make one big tank not sure on that yet what size and materials is you big tank

[@josh-kh2wh]

Does this work for grain or just substrate mate ? Chow

[@AllanDaviesOriginal]

Hahaha I lost it with " yolo" bloody classic

[@zacm4740]

Does this sterilize the grain spawn? Or the substrate? Or both? An how long would you have to leave 10 individual bags of grain in there weighing 3 pounds each? And what is the cost to run it? I eagerly wait for your response, thanks. ✌️😎

[@andrew1717xx]

Never disappointed.

[@BoroBootBoy]

I would hope by now that you have a multimeter to test circuits?

[@OakandSpore]

Of course! I tested the switch prior.

[@filippoostuni3251]

@@OakandSpore hello mr TOM DO YOU HAVE ANY VIDEO ABOUT YOUR SPAWN STERILIZER. Is it ok

[@dr-bl8ph]

love the vids informative and the off the cuff jokes kill me

[@taskos1261]

Hey Tom, is there a connection with 20kgs and pressure or just about that much weight?

[@RakkaSan7219]

Oy!! How safe is it using a specific weight for lid allowing some pressure to build wo being explosive??? What weight is best and what pressure will it allow by weight? I'm thinking and have been before I saw your vids...but since.you already do or have...but I'm thinking a 55gallon barrel which will be boiler to flow from and into my insulated box...maybe even a few bats in the barrel also before being hosed to the box. Any pointers or Advice? Also 55gallon barrel w the lid being held on with bicycle tire inner tube as the "ring" holding the lid on. A quick summary is all I'm asking on weight of lid cover for pressure safely but ill take all you wanna say!!! Thx mate

[@Johnny-ur2st]

Vinegar will clean that scale off I use it in my water maker just boil then scrub

[@user-sn5uw7it5u]

Great stuff! Can you also add the Safety Float Switch dimensions to the the steamer blueprint? Cheers Also, the straight arm float valve you linked: Are we supposed to bend it when we install it?

[@OakandSpore]

So the straight arm can be installed on the underside of the device. I will throw a link for the bent arm on on the video now.

[@johnnyperkins79]

How many gallons is your boiler ?

[@kangarooislandmushrooms]

Love it

[@user-sn5uw7it5u]

Hi Tom, a few questions: - Does the steamer blueprint you sell now reflect the location of the Safety Float Switch? - Did you end up adding the Temperature Switch that you mentioned in your earlier video (which you couldn't install at the time of your arm injury)? - Any idea when the wiring schematics for the PID will become available? Great work as always!

[@OakandSpore]

No, the blueprint doesn't have a hotel drilled for the float valve. I've left it out so people can drill a hole for their specific valve. All you need is a drill. Wiring diagrams are on the horizon, but I've got a full plate, so won't be too soon.

[@user-sn5uw7it5u]

@@OakandSpore Awesome - and also, did you end up adding the Temperature Switch?

[@OakandSpore]

No, just the float switch.

[@user-sn5uw7it5u]

@@OakandSpore Yeah fair, did you just deem the float switch to be enough? Just want to understand the reasoning :)

[@OakandSpore]

Yeah, it works well. I purchased a high quality German one.

[@imanderdumme8706]

Clever 😍😍👋🏻

[@Coxlife]

Can you sell this .

[@jessecampbell5944]

Yolo!

[@OakandSpore]

100% yolo!