OPENING PANDORA.S BOX TOOL CABINET?

  Рет қаралды 39,975

mrpete222

mrpete222

Күн бұрын

Пікірлер: 638
@Drew_Snydermann
@Drew_Snydermann 4 ай бұрын
The CJ2004 puller set is $1,500.00 new from Snap-on, The CJ2003 is $805.00. Figure half price or even more for used. Had those sets at my auto shop, excellent pullers. It looks like you may have most or all of the Snap-on master puller set CJ2000S, which is $4,800.
@sithus1966
@sithus1966 4 ай бұрын
Even if sold at 1/3 of the new price Lyle would probably make the cost of the lathe back
@andyZ3500s
@andyZ3500s 4 ай бұрын
ex​@@sithus1966plus some extra for accessories.
@jimlahti1613
@jimlahti1613 4 ай бұрын
The older Snap-On stuff is super collectable and should bring you a premium price. Enjoy the Atlas shopping spree you'll soon be on!
@windrk_6754
@windrk_6754 4 ай бұрын
You might pick out one or more of the good sets & offer separately, if you don't get a real good offer for everything.. then buy some amazing accessories for the Atlas.. but you are wise to not want to put too much time into it.. I kind of perked up at the Clausing price.. didn't hear what the Maximat went for .. if they were not sitting too long, either might not have been too bad a cleanup..
@ThisMFINGuy
@ThisMFINGuy 4 ай бұрын
wow
@VB-bk1lh
@VB-bk1lh 4 ай бұрын
The contents of that cabinet just made that a fantastic deal, the lathe is just icing on the cake. The Snap On puller set, the long OTC puller, and the various specialty automotive pullers make that a better than $5k load of tools. Many of the unbranded pullers may just be OEM supplied tools. The total value of those pullers far exceeds the value of the lathe, even in perfect condition. I've got most of those pullers from years of working in dealerships and I can't even imagine how much they all cost total when new.
@westbygodvirginia555
@westbygodvirginia555 4 ай бұрын
You sure did better then Geraldo! Thanks for taking us along.
@sd906238
@sd906238 3 ай бұрын
Geraldo's career never recovered after that.
@gmarth8658
@gmarth8658 4 ай бұрын
Snap on,OTC, pin presses! . No doubt will pay for old lathe. Congratulations Mr. Pete
@daveboatman4024
@daveboatman4024 4 ай бұрын
I think the former owner was pulling your leg by putting all the pullers in the cabinet. One thing I have learned over my 72 circuits of the sun is that the higher my expectations, the greater my disappointments. No expectations, no disappointments.
@frogandspanner
@frogandspanner 4 ай бұрын
Same circuits here.
@SkylerinAmarillo
@SkylerinAmarillo 4 ай бұрын
It reminded me of Geraldo Rivera and Al Capone’s secret stash that held nothing,
@plainnpretty
@plainnpretty 2 ай бұрын
I thought it was just the cabinet he keep his pullers in . Thanks Mr Pete
@dannyl2598
@dannyl2598 4 ай бұрын
Thanks Mr Pete. I'm sorry it wasn't what you were hoping for, but I'm glad it was something of value and not scrap metal. You probably got the only thing at the auction that wasn't ruined. I wish you a quick recovery from that tooth.
@Duckfarmer27
@Duckfarmer27 4 ай бұрын
That is a set of pullers fit for the maintenance tool crib of a good size manufacturing operation, never mind the purely automotive stuff. You did great - as others have said don't let it go too cheap as many are high dollar sets. Great video.
@oldbowsaw9001
@oldbowsaw9001 4 ай бұрын
Old Cat mechanic--Having and using a puller that makes the job easier is priceless for me!!!!!!!!!!! Like to have them all!!
@jamesdavis9774
@jamesdavis9774 4 ай бұрын
Disappointed he says! Not to insult him. But I own 95% of what he has shown. Including the lathe! I'm never disappointed in owning tools, especially when a person spends pennies on the dollar. But maybe the difference is I use them daily. I don't do it for the resale.
@larescats9228
@larescats9228 4 ай бұрын
@@jamesdavis9774is that jamie davis from bc
@janderson8401
@janderson8401 4 ай бұрын
@@jamesdavis9774 I don’t think Mr. Pete buying this to flip it. He may have been thinking of making one or more videos on restoring the lathe.
@dhess140
@dhess140 4 ай бұрын
This is not the collection of a backyard mechanic. Very impressive.
@gorak9000
@gorak9000 4 ай бұрын
I love the disdain for any tool that doesn't have a name on it, but the absolute love for a rusted out pos lathe
@JonBanquer
@JonBanquer 2 ай бұрын
Too funny.
@RodneyHayes-d3y
@RodneyHayes-d3y 4 ай бұрын
Had a repair business thirty plus years and had everything you unpacked easily when I retired. There's easily eight to ten thousand dollars new cost for what you unpacked
@mrpete222
@mrpete222 4 ай бұрын
Wow
@alro2434
@alro2434 4 ай бұрын
@@mrpete222 Remember he said 'new', and not many people but a puller hoarder would have or want so many duplicates.
@herbholmberg4474
@herbholmberg4474 4 ай бұрын
Regardless how you look at it, new, used does not matter. Even used the sale of all of those pullers should fetch several thousands dollars in total. The buy of the day was not the lathe, it was the contents of that cabinet! ​@alro2434
@dougvanallen2212
@dougvanallen2212 4 ай бұрын
You hit the jackpot Mr Pete
@29chevbolenschannel40
@29chevbolenschannel40 4 ай бұрын
The good thing about the items in the cabinet is they were protected from the rust. Sorry that you only found the 4 jaw chuck as the only lathe part but that is one less thing you will need to locate. The good thing with the Atlas Craftsman 6" series is that there is lots of tooling that can be found - just need deep pockets - hopefully you can sell the pullers and come out ahead enough to purchase most of the tooling and that the lathe itself cleans up to the point where it is useable. Thanks for the mystery tool cabinet episode - I enjoyed it.
@leeroyholloway4277
@leeroyholloway4277 4 ай бұрын
A few thoughts: When you need a puller, nothing else will do. -- This video is way more exciting than Geraldo's TV special. -- My Dad always said, "Locks are for honest people". (of course I'm not implying anything towards you Mr Pete) Thanks for sharing the adventure in spite of the lack of lathe tooling.
@fr73ed38
@fr73ed38 4 ай бұрын
"When you need a puller, nothing else will do." Absolutely well said.
@samshublom8761
@samshublom8761 4 ай бұрын
I remember watching a 60 Minutes piece about pick pockets. They interviewed an old ex-con pick pocket who lamented that nobody was learning the "trade" anymore and these days they "just knock you in the head and take your wallet." He said the same was true with lock pickers. It is easier to knock the door down than to learn how to defeat the lock. I was pretty impressed with how fast you got into that cabinet...and I hope the kid who taught you will get out soon.
@timeflysintheshop
@timeflysintheshop 4 ай бұрын
HOLY MOLY! THE MOTHERLOAD OF PULLERS!!!! You can definitely sell the Snap-on stuff for what you paid for everything! You did very well! I wished you luck at that auction, and IT WORKED! 👍😁👍
@mrpete222
@mrpete222 4 ай бұрын
Thanks 👍
@wvrockcrusher
@wvrockcrusher 4 ай бұрын
Wow! You did very well even though it wasn't what you were hoping for. At least you found the 4-jaw for the Atlas. Maybe he never had any other accessories for the machine? I can tell you those Snap-On puller sets are worth far more than what you gave for the lathe as they look brand new and complete. I have a lot of those pullers and slide hammers because I work on a variety of things from automotive, industrial machinery, farm equipment, machine tools, etc., so that's probably why he had so many different pullers. The 3-in-1 sets are for ball joints, bushings, u-joints, or whatever else you can think of. Saw some pitman arm pullers, steering wheel pullers, tie rod tools, etc. You should make your money back and have plenty to cover getting the needed accessories for the Atlas with no problem, given the right buyers show up. That is a very nice cabinet and is worth a little cash by itself, although it is perfect for the Atlas to live on. I bought an Atlas just like that one a few years ago at auction for 50 bucks, but it came with a crate full of every accessory under the sun, which was worth more than the lathe. I'll have to look and see if there are any doubles in the crate that I don't need. If there is, maybe I can send you something for yours.
@TheAyrCaveShop
@TheAyrCaveShop 4 ай бұрын
Great Video ! Best quotes of the morning : “I think he’s in the penitentiary” “ Holy mackerel, is that a puller”
@garethhoward3995
@garethhoward3995 4 ай бұрын
Be of great cheer! Finding new, or almost new, Snapon tool sets is always a good thing. I'm sure you will come well financially and mentally.
@davida1hiwaaynet
@davida1hiwaaynet 4 ай бұрын
Fascinating! It's a crying shame that the remainder of the Atlas accessories weren't in the box! It sure seems like the owner of that did quite a bit of suspension and undercarriage work on cars. Makes you wonder what the lathe was used for in such a shop. One item which seems out of place with all the automotive puller tools is this - At 22:51 you open the lower drawer of one of the small red boxes and pick up a small tool with a slot in the center and some round holes, and two wing nuts. You mention it may be a flaring tool. That is actually a refrigeration pinch-off and re-rounding tool. The "jaws" in the center can crush copper tubing and stop the flow of gas. Once you have performed your service procedure, you place the tube through one of the round holes, and close the tool again. The round hole will "re-round" or open up the copper tubing. Many decades ago, before the advent of Schrader valves, people would use this tool to prevent loss of their refrigerant charge while disconnecting gauges and placing a cap over a non-Schrader service port. Or, they would cut the tubing and solder the end closed after servicing the system. I have a hunch that the people at the car shop "may have" used those to close off brake hoses to stop the loss of brake fluid while doing suspension work. This is a bad idea since it damages the hoses, but people do it regardless. I did get a kick out of the lockpicking. Some of us don't like destroying things, including locks. I had to learn to do this as well, to open some of the old soft drink coolers I repair. The lock cylinders are typically available but often if you try to destroy the lock, other parts of the mechanism (made of pure unobtainium) get damaged as well. Looking forward to seeing your travels and auction browsing videos this year, as well. Thanks and please keep them coming!
@mrpete222
@mrpete222 4 ай бұрын
Thanks for some great advice and solutions
@randallthomas5207
@randallthomas5207 4 ай бұрын
Tractors. Farm auction, pretty much everything in the cabinet, would work on tractors, and the lathes would let the owner fab their own hard to locate parts.
@shandylynn1
@shandylynn1 4 ай бұрын
@@davida1hiwaaynet 30yr HVAC/R guy here. I saw those too and used them years ago. Don’t much anymore due to the damage you mentioned. We do use a specialized vice-grip pinch-off working with newer, small refrigeration units because law requires we pinch off and solder she system shut with no service ports. These are R-290 (Propane) units. Weird the new laws require it, the old cascade systems I used to work on for -100°F boxes that were used, ironically, in an aircraft machine shop for interference fits. Full circle I guess! 😂
@daviddavies1596
@daviddavies1596 4 ай бұрын
The lathe was probably used to make parts for pullers!🤣🤣
@stevezwemer1262
@stevezwemer1262 4 ай бұрын
While you didn’t find what you wanted in the cabinet, you scored on the pullers. A reasonable sale price ought to line your pockets and help purchase the tooling you need and want. So I call it a win and this amazing video ought to boost your channel. Keep up posted on how the puller sales go…. I smell money….
@DJPLAST2
@DJPLAST2 4 ай бұрын
I am glad you did not find a LEG PULLER! I feel comfortable that you won’t be pulling our legs in the near future.
@RickRose
@RickRose 4 ай бұрын
You picked that lock like a boss! Glad you were able to save the nice cabinet. I hope someone made you a good offer on all the pullers.
@evil16v1
@evil16v1 4 ай бұрын
The lockpickinglawyer is a great channel. Ive changedthe way i look at security because of him. A lot of people criticize him for "showing people how to pick locks". The thing is, the people that you need to worry about, already know how to do that. He is showing you how to deal with them, and why.
@roberthoug7864
@roberthoug7864 4 ай бұрын
No criminal takes the time to pick a lock with Today's equipment. The only one picking a lock is the one that needs to save the Cabinet for his use. the criminal cares nothing about your cabinet he just wants what's inside. On the other hand, if he likes the cabinet, he'll just take that along with him and pick the lock at home. eagle
@rustywrench2119
@rustywrench2119 4 ай бұрын
Wow, you hit the jackpot on that cabinet contents. Anyone with a shop would love to make a purchase like that. Lots of value in those pullers.
@mpetersen6
@mpetersen6 4 ай бұрын
Back when l was rebuilding spindles for machine tools (box, cartridge and cartridgeless styles) l ordered a couple of sets of pullers that most people never see. The Snap-On (1) set for pulling dowel pins that are not drilled and tapped. That one consisted of collets with a collapsibg sleeve. The other was either Snap-On or OTC. That was the one for pulling bearings from blind holes. Sleeves with slits cut in them and a tapered ID. An expansion plug would expand them and they had a shoulder that would rest against the inner race. Also had the SKF bearing installation set that covered from 101 to 310 ball bearings. Later when l was rebuilding industrial centrifuges we had SKF 3 jaw hydraulic pullers. I wanted to make up adaptors to use the hydraulic pump and cylinder on other applications but there was never the time. Always too busy. 1) Coporate headquarters is about 3.5 miles away from my house.
@mrpete222
@mrpete222 4 ай бұрын
👍👍👍
@mpetersen6
@mpetersen6 4 ай бұрын
@@mrpete222 For slide hammers l had three different sizes l made up myself. One had a Slide Hammer that weighed around 8 pounds. Needed the extra umph for work on stamping presses.
@brucemitchell9166
@brucemitchell9166 4 ай бұрын
Can't believe there were so many pullers in that cabinet. Many are in good condition & should sell . Good luck from South Australia Thanks for your videos
@peltona
@peltona 4 ай бұрын
We were dying to know what was in there. You got two great finds this trip and I think the contents makes the price you paid well worth it.
@CalPil0t
@CalPil0t 4 ай бұрын
Ebay sold prices puts you at least at $1000. Quite a haul. You will be able to get the accessories for the Atlas 6. Thanks for sharing.
@HenningJohansen
@HenningJohansen 4 ай бұрын
Your Snap-On CJ2004 puller set is listed on ebay for $1,200! You can no longer complain that you paid way too much for the lathe. 🙂
@firesurfer
@firesurfer 4 ай бұрын
There is another, nearly new for $725.
@bhartwigutube
@bhartwigutube 4 ай бұрын
The guy was a motor mechanic based on the brake lathe. They are all big money. That snap on kit is probably a few thousand. The big forcing screw looked like part of a brake drum puller which was used for tapered axles... The "mummy" H frame looks like what OTC sold as a pusher / puller. Maybe for kingpins? The vise grip puller looks like Snap On slide hammer too... same with the small 3 jaw.
@ravenbarsrepairs5594
@ravenbarsrepairs5594 4 ай бұрын
I've put a lot of use on the Harbor Freight pulley installer and remover sets of that vintage. They're nearly indestructable. The modern Maddox Fuel injector tester is also fairly decent.
@d.pierce.6820
@d.pierce.6820 4 ай бұрын
I buy every puller I see at yard sales and auctions-you can't have too many, and having the right one for a job is priceless.
@williamparker8318
@williamparker8318 4 ай бұрын
Nice haul Mr Pete. The tool in grey box that you thought was for u-joints is for removing ball joints. Cheers
@theseldomseenkid6251
@theseldomseenkid6251 4 ай бұрын
Wow, awesome deal on a huge collection of pullers. Plus, they threw in a free lathe.
@billdoodson4232
@billdoodson4232 4 ай бұрын
That is a totally fantastic haul.
@nevetslleksah
@nevetslleksah 4 ай бұрын
If you paid $450 for the 6” Atlas lathe and the cabinet congratulations you made out.
@Ironman-harmonica
@Ironman-harmonica 4 ай бұрын
Everything in the cabinet was worth way more then you paid. Great day at the auction
@Bargle5
@Bargle5 4 ай бұрын
I don't think you'll have any trouble getting most or all of your money back on this one. What a collection of pullers. 😮
@DigitalVideoFromOz
@DigitalVideoFromOz 4 ай бұрын
You are the best! Only someone like you could go to the dentist for a tooth pulling, and then later in the day open a secret cabinet filled nearly completely with pullers of other kinds. Oh the ironies of life! ❤
@mrpete222
@mrpete222 4 ай бұрын
😁👍
@chuckfischer7202
@chuckfischer7202 4 ай бұрын
Quite a variety and several duplicates. At about 22:51, right after the small bearing splitter, small unamed tool. Removes and installs the retainer on the drive end of Delco Remy starter motors. Handy gadget, even if only to replace the Bendix. Good pullers aren't cheap. Cheap pullers are worth less than nothing.
@johnmorris4753
@johnmorris4753 4 ай бұрын
Those aren't u-joint pullers, they are for removing and installing ball joints on pickup trucks and and vans. I recently used one on my 97 ranger. A mechanic would love to have all that stuff. You could easily recoup some of your money.
@jimmydm3
@jimmydm3 4 ай бұрын
Steering wheel lock ring depressor, Lisle lifter puller, rear axle bearing pullers, ball joint and tie rod separators, suspension bushing pullers, auto trans front bushing puller. Lot's of automotive stuff. I saw a power steering pulley remover, pilot bearing puller and othe goodies too. A treasure trove of stuff. You scored.
@shandylynn1
@shandylynn1 4 ай бұрын
Wow - awesome auction success!! They DO have little slide hammers in dentistry! I have 13 or 14 crowns, bad teeth all my life. Had an old Army dentist. Dr. Ben Bell who was a fast, no nonsense guy - great dentist. He did 6 crowns at once for me and used his little slide hammer for pulling the new crowns off when they got stuck as he was fitting them all before cement. It had a little claw hammer like hook. Anyway, I commented that I had a much larger one should he need it and that got a little laugh from him.
@mrpete222
@mrpete222 4 ай бұрын
👍👍
@1924ab
@1924ab 4 ай бұрын
They have some really sweet miniature torque wrench’s that are used for installing implants!
@xoxo2008oxox
@xoxo2008oxox 4 ай бұрын
All worth just hearing how you learned to pick locks!
@mrpete222
@mrpete222 4 ай бұрын
😁
@rlewis1946
@rlewis1946 4 ай бұрын
Good for you, Mr.Pete! You bought the insides “sight unseen” and you came out on top!! Happy for you. RL Buffalo, NY
@alro2434
@alro2434 4 ай бұрын
Great Video Mr Pete, a goldmine of duplicates is still a goldmine. Our only disappointment is that you're disappointed, it's gotta be the tooth talking!
@mackcrane7349
@mackcrane7349 4 ай бұрын
You will more than recoup your investment on those Snapon pullers. A good puller is worth it's weight in gold when you are in a bind. Have fun with the Atlas , will all love to see your progress.
@mrpete222
@mrpete222 4 ай бұрын
👍
@basilseal
@basilseal 4 ай бұрын
the puller legs in the two red boxes go with the hydraulic puller you found at the start, not familiar with the brand but looks similar to the sykes pickavant brand we have in the UK, the reason there's only one leg in the first box is because the puller swaps between two and three legs and it was set up for two with the other two legs that match this one, the different length legs swap for different operations. IMO the pullers are worth more than you paid for the lathe.
@jimintaos
@jimintaos 4 ай бұрын
Well,Mr. Pete ya done it again. You reminded me once again that I need to redouble my efforts to clear out my accumulation of stuff before I meet my well deserved end. I hate the thought of a bunch of people at an auction wandering around wondering what kind of mental case I might have been to have collected all this stuff and then let it all go to rack and ruin.
@bobmazzi7435
@bobmazzi7435 4 ай бұрын
Why? If you have fun in life and depart with a smile, who cares what happens next. Let your family know where to get decent value if they want the money, or just let them recycle it if they are rich.
@johncloar1692
@johncloar1692 4 ай бұрын
Nice picking the lock, Enjoyed the video. Sorry not much in the lathe tools. And as always a thumb up from me. Hope your Jaw get to feeling better. Thanks again Mr. Pete.
@4GSR
@4GSR 4 ай бұрын
With the money made off the pullers. You should be able to go out and buy another Atlas lathe complete with all of the accessories!!! Great find you have IMO!
@kilosierraalpha
@kilosierraalpha 4 ай бұрын
That has to be the world's biggest PULLER collection!
@hughdanaher2758
@hughdanaher2758 4 ай бұрын
There must be a museum some where that needs their linoleum floor stuck down😊
@1pcfred
@1pcfred 4 ай бұрын
It is impressive. You would be the puller king with all of that.
@oldbones3092
@oldbones3092 4 ай бұрын
You're fortunate that you have auctions like that in your area. Here, there's nothing like that. Been looking for a small lathe, but nothing anywhere within 3 hour driving.
@thelotusguy
@thelotusguy Ай бұрын
Lyle you can start a puller museum. This has to be the best collection of all time.
@rustyblade5845
@rustyblade5845 4 ай бұрын
Wow. You've hit the jackpot. Glad you released the show early. Don't think I could have waited . Snap-on fetches a fortune in England. Most men are obsessed with pulling.😮😅😊
@johnmcdyer1573
@johnmcdyer1573 4 ай бұрын
Ha ha ha 😂😂😂😂😂
@ggordon4127
@ggordon4127 4 ай бұрын
I was completely unaware of a " puller fetish"
@charlesangell_bulmtl
@charlesangell_bulmtl 4 ай бұрын
puller fetish?....here, pull my thumb Pullers multiply when you don't have exactly what works... Collections like that result from investment, not fetish.
@brucecliffe6213
@brucecliffe6213 4 ай бұрын
Hi Lisle, Those pullers etc are worth far more than that lathe is worth mate. I just bought a couple of the sets you have shown there and I paid more than I would give for that lathe. That contents of that cabinet is probably worth 10 times what the lathe is worth in my opinion. I have owned a Lathe for 40 odd years (12" X 3Ft.), so I know the value of a lathe to a machinist, further, I just bought a new lathe and a new milling machine and I am still using pullers (Obviously as I just bought some new ones) such as you have shown, I am 78 and still very active. You got a bargain there mate, don't knock your good luck. Hope you find a good home for the bits you don't want. Thanks for sharing your day with us. Cheers from Australia.
@mrpete222
@mrpete222 4 ай бұрын
👍👍👍
@billwalck1324
@billwalck1324 4 ай бұрын
The tool in the funky box with the duct tape appears to be a king pin pusher. It ius remarkably similar to the accessory for my Snap-On press that performs the same function.
@Garth2011
@Garth2011 4 ай бұрын
Unless there is a shortage of dentists in your area, I would consider finding another one if you feel that way. Most dentists would prefer to restore a tooth, depending on which one it is. Pulling teeth is the last resort with any decent DDS. Also, the cheapest procedure they do.
@johnoconnor5581
@johnoconnor5581 4 ай бұрын
One of the funniest Mr Pete videos I’ve seen, best one since the rant about living in a hi-rise condo in retirement. I hope you don’t have to pay too much to have all those pullers hauled off
@mrpete222
@mrpete222 4 ай бұрын
😁😁
@reamer1363
@reamer1363 4 ай бұрын
Thank you so much for this video. By the end when you are checking the red tool boxes I was literally in tears with laughing. The anticipation of what I already knew would be another puller was overwhelming. Great video and thanks again. Bonus on the 4 jaw though.
@ScottWM54
@ScottWM54 4 ай бұрын
The tooth & the mother load of pullers...glad you waited to open the cabinet......would've given you a complex...😅🦷🦷
@ahill7099
@ahill7099 4 ай бұрын
one things for sure if anything is stuck on the atlas you can PULL IT RIGHT OFF. LOL. have a blessed day
@Rbrown-kk3tz
@Rbrown-kk3tz 4 ай бұрын
the Snap-on puller set cost way more than you paid for the lot.
@727jetjumper
@727jetjumper 4 ай бұрын
Nice haul Mr. Pete!... that Snap-On stuff alone should net you a nice ROI.
@funone8716
@funone8716 4 ай бұрын
The man that owned that cabinet wasn't just pullin our leg. But he was pulling everything else. Mr Pete you could start a Puller museum with your new extensive collection.
@markavis7232
@markavis7232 4 ай бұрын
Maybe someone has already told you this - the first puller you look at is kind-of hydraulic. You fill the central small dia hole with grease (remove the screw with the tommy bar in it first), take the slack up with the large fine thread you mentioned, and then use the central small tommy-bar driven screw to push the grease - the business end of the ram floats inside, as is driven out by the grease as you tighten that central screw. They work rather well.
@mrpete222
@mrpete222 4 ай бұрын
Someone else told me that, but you are the one that explained it explicity thank you
@rjsenn4142
@rjsenn4142 4 ай бұрын
Great video! I still remember watching that dopey Geraldo vault scam! I have the opposite dentist, great guy and very talkative. He even showed me his crown making cnc as it was making the one for me. Incredible machine!
@klingonbaronessprincesskar5519
@klingonbaronessprincesskar5519 4 ай бұрын
Love your channel keep it up very rare information young generation needs you
@toddhazell925
@toddhazell925 4 ай бұрын
All you need to know is that all of those tools would have paid for your lathe and possibly enough to buy those accessories for it.BTW, that 1st puller you took out is a hydraulic puller that belongs with the 1st red toolbox that you looked in.
@douglasbattjes3991
@douglasbattjes3991 4 ай бұрын
You hit the jackpot , puller heaven, and one 4 jaw Atlas chuck. & 400 pullers, but the prize is the Snap-on stuff. 👍👍
@joemion666
@joemion666 4 ай бұрын
Well you have a fortune in pullers, but I don't know anyone who would need that many pullers. I have used some of these large 3 jaw pullers on 3 ph motor sheaves for cooling towers but I did not enjoy it at all. I knew you would have no trouble picking that lock, by the way my old friend and foreman who was a WW-2 vet taught me to pick locks in fact we even cut some locks in half to see how to make master keys. We worked in a large hospital and the nurses would often loose their keys.
@mrpete222
@mrpete222 4 ай бұрын
👍👍
@dennythomas8887
@dennythomas8887 4 ай бұрын
That ratchet you pulled out with the "T" handle is called a "Sidewinder" and came in 1/2" and 3/8". They were made for turning nuts and bolts in areas where you can't swing a normal ratchet or wrench. I have them out in my shop some place. I was a young "hot rodder" back in the early 70's and my Dad got them for me for Christmas, which is why I haven't tossed them. They are pretty much useless due to the size of the head . Vintage tool collectors love them because they were an odd ball tool.
@mrpete222
@mrpete222 4 ай бұрын
I had a feeling they were probably a novelty
@lesstreble
@lesstreble 4 ай бұрын
That was genuinely fun! A Sunday morning cup of coffee and a fresh Mr. Pete video is a perfect combination. Keep'em coming!
@earlmiller6093
@earlmiller6093 4 ай бұрын
I laid on my bed and thourghly enjoyed this…. Laughed n laughed…. You were my morning entertainment!!! Thanks Pete
@mrpete222
@mrpete222 4 ай бұрын
😁😁😁😁
@DominickCascianoIII
@DominickCascianoIII 4 ай бұрын
so glad you were the one to get this!
@rogertaylor1589
@rogertaylor1589 4 ай бұрын
My dentist had the same reaction to my dental dynamite suggestion. Seems like a steady & follow rest is all you need? Great presentation & suspense.
@G1951-w1y
@G1951-w1y 4 ай бұрын
The previous owner was a pulling son-of-a-gun. I'm glad some viewers are identifying some of those tools with good value for you. Despite your disappointment, you did well, Mr. Pete.
@walterplummer3808
@walterplummer3808 4 ай бұрын
It is still fun looking thru all of your "treasure". Thanks for the videos.
@ganoncollins1
@ganoncollins1 4 ай бұрын
Wow, thought I had a lot of pullers, nothing like that haul! Good find!
@coldpond
@coldpond 4 ай бұрын
I'd say sell everything including the lathe. Save monies till next auction or buy lathe with parts included. Save time and extra money.
@fordbroncodave
@fordbroncodave 4 ай бұрын
As far as I am concerned the amount of name brand pullers in there is far more than that lathe is worth.
@TheGrimReaper1
@TheGrimReaper1 4 ай бұрын
That bloke who restores old stuff could fix the chuck (i expect) no need to throw it away. All the best from England .
@moominjuice2
@moominjuice2 4 ай бұрын
I love a mystery box but that made me chuckle even though it was a disappointment. Man, that guy must have had every conceivable puller there is :) Shame as I was really rooting for you finding some nice accessories that would make that lathe a great clean-up project you could just get stuck into. Gutted for you Mr Pete. Best of luck on the sale.
@michaelmaltby6203
@michaelmaltby6203 4 ай бұрын
Man, you are all set now. Anything needs pulling and you are the go-to guy Mr Pete. You could corner the market 😂
@kevinkoepke8311
@kevinkoepke8311 4 ай бұрын
Good ol' Charley was driving through some country, several hundred miles from his house. When low & behold his car started to make a horrible squealing noise. Long story aside, he needed a special puller to do a task he was quite familiar with. Having to pay $$'s to a man to accomplish a job he could have done himself, he YELLED, and proclaimed, "NEVER AGAIN!!!" Thanks, Mr Pete
@bobmazzi7435
@bobmazzi7435 4 ай бұрын
I think you did well. I could see a couple of ways to go forward. First, put it on consignment at your machinery dealer. Perhaps using the credit towards the Atlas stuff you want. Second, chase down the SnapOn truck and ask him for an offer. Most of them would buy the SnapOn stuff at half price and sell it on at 3/4 price. Cash. They usually do take trades so buying used would not scare them. Third, visit the local auto repair shop and ask the techs what they want, I'd expect to be able to get a couple of grand easy. Forth, visit whatever local maintenance shops there are, even the School Bus Garage or factories that work on their own machinery. And the final option is PeteBay, Puller edition. Shipping would be a bear, but a cuople of hundred bucks to ship a thousand buck sale is not the worst thing in the world.
@mrpete222
@mrpete222 4 ай бұрын
👍👍
@magicbytes3835
@magicbytes3835 4 ай бұрын
Hello mrpete, WOW, I am guessing you got at least $3,000.00 worth of pullers there, I was thinking you got a face plate, stationary and moving steady's, driving dogs and a 4 jaw chuck which you scored, I am disappointed too, tool holders, parting tool holder, thanks for sharing with all of us interested viewers, cheers from me. 😃👍👍👍👍👍
@jimfiles3307
@jimfiles3307 4 ай бұрын
It looks like we will see PULLER BAY silent auction. What a great find. I would keep the big Snap On set for the tractor.
@nealblackburn8628
@nealblackburn8628 4 ай бұрын
you don't sound very happy with your haul but for the right person that collection of special tools would be gold
@lito11111940
@lito11111940 4 ай бұрын
The man was obviously doing front end alignments. I think you hit the jackpot, that's a pretty big bundle spent on pullers and I can obviously say you'll never get stuck.
@kirkstewart2616
@kirkstewart2616 4 ай бұрын
Make sure you check the prices on that Snap-On stuff before you sell it, I'm sure you will. Also I guess we know where the last" What Is It? " came from!
@JamesOsborneJr
@JamesOsborneJr 4 ай бұрын
I have most of those pullers being a retired mechanic , you should make well and above what you spent at the auction . a very good buy for sure.
@joemcgarry1106
@joemcgarry1106 4 ай бұрын
I learned to pick locks from a girl in my high school class. Her father was a locksmith. That was 50+ years ago. it is a skill I had occasion to use through my whole life.
@mrpete222
@mrpete222 4 ай бұрын
👍👍
@jankarlsson8927
@jankarlsson8927 4 ай бұрын
In dental practice we already use a slide pullers to remove dental crowns. A very useful tool indeed, but thanks for the tip mrpete :-)
@mrpete222
@mrpete222 4 ай бұрын
Are you a dentist?
@MrUbiquitousTech
@MrUbiquitousTech 4 ай бұрын
Wow, that's a nice haul of pullers! That alone was worth the purchase price! I have a some of those harbor freight ones, even those work well.
@WrenchHead
@WrenchHead 4 ай бұрын
Wow! After seeing the contents within, you did well on your buy. You probably won't have any issues reselling the contents.
@SteveSchuh-tr3rb
@SteveSchuh-tr3rb 4 ай бұрын
At 11.30.. that 3 jaw puller is a GREAT tool. Made in ND. It is tuff and strong. Reasonable price..and they used to send replacement parts free! 3 jaws and a stabilizer to hold it all in place!
@rediband
@rediband Ай бұрын
That looks like Bugsy Segal's gold bullion safe from the 1936 Wells Fargo Stagecoach heist!
@mrpete222
@mrpete222 Ай бұрын
Lol
BIG SUMMER TOOL AUCTION- Nice Scores tubalcain
35:00
mrpete222
Рет қаралды 62 М.
When Cucumbers Meet PVC Pipe The Results Are Wild! 🤭
00:44
Crafty Buddy
Рет қаралды 58 МЛН
كم بصير عمركم عام ٢٠٢٥😍 #shorts #hasanandnour
00:27
hasan and nour shorts
Рет қаралды 10 МЛН
This Should Be Impossible...
23:05
Alec Steele
Рет қаралды 359 М.
FACEPLATE FOR ATLAS 618 Lathe #1002 A tubalcain pt 10
18:55
mrpete222
Рет қаралды 6 М.
Best 10 Items I Tested in 2024!
20:12
Project Farm
Рет қаралды 310 М.
Keyway repair on grinder shaft
15:02
On Fire Welding
Рет қаралды 142 М.
How's a Guy Supposed to Work Like This?
24:19
Inheritance Machining
Рет қаралды 713 М.
Fixing Broken Fishnets
17:18
This Old Tony
Рет қаралды 440 М.
So a lathe walks into a bar...
24:16
Inheritance Machining
Рет қаралды 458 М.
ANOTHER FANTASTIC Hoarder TOOL AUCTION #972 tubalcain
40:57
mrpete222
Рет қаралды 30 М.
Big Power! 14000 Watt 892-R Transmitter Tube - Will It Work? Power It Up!
16:09