Outside Tap installation easy step by step easy diy tutorial by a plumber on a job easy outside tap install
Пікірлер: 50
@gregmason4409 Жыл бұрын
- hmmmm - No pipe sleeve, no silicone, no double check valve - don't be doing my outside tap thanks
@djdaviddeomont667411 ай бұрын
I was thinking the same thing 🤔
@JoshD28010 ай бұрын
Clearly the bloke shouldn’t be plumbing
@lemonlad9823 ай бұрын
If you know what your doing why are you commenting on a video to show you how to do it?
@gregmason44092 ай бұрын
@@lemonlad982 Because unskilled people are watching this video to see how to do it themselves to save money - and it's wrong
@almilhouse90593 жыл бұрын
Definitely would put silicone in there on the outside to seal up nice so no water go in behind.
@Dragon-Slay3r8 ай бұрын
I just heated up a small spoon and melted the pipe to fix the leak maybe Ile do the same on the other leak which a hospital glove is holding it Is this why we attacking hospitals so I run it? 😭
@Builtbypete Жыл бұрын
Great job. Cheers.
@mattthomson19822 жыл бұрын
Nice job mate, just finishing off my level 2 plumbing, hope I get jobs like this!
@krazykillar47942 жыл бұрын
This exactly what I've needed . Never thought I would subscribe to a plumber . 😆
@stargategoku11 ай бұрын
Thanks a lot , mate, for posting
@stevegreen3442 Жыл бұрын
Thanks for this but pretty expensive using those push fits!
@darrenbeechall18304 ай бұрын
Helped me that kidda cheers 👍
@bbl8791 Жыл бұрын
Was curious to see how you got that last piece of copper piping in, I guess you just stretch the lower and top pipes apart, if there's no play i imagine you would have to do it differently.
@Zaine222 жыл бұрын
Why not use a pipe bender to get in front of the hot pipe and put the isolation valve on the vertical straight
@keithletheren1962 жыл бұрын
And fix the loose kitchen tap and not let the water go all over the floor…
@tonyb95782 жыл бұрын
M8 I have a tap like that just installed. Could you tell me what kind of adapter I need to put on it. I need one that will attach to my hose end connector. Thank you in advance.
@andl_handle Жыл бұрын
Yes I'd like to know too please
@Mushroom3D2 жыл бұрын
Any idea how to add a hose to one of these I cant find the right thing anywhere. Clueless.
@liamtaylor51222 жыл бұрын
nice video man! however, one question; if theres two isolation valves on the two hot and cold pipes do i put the tee above or underneath the valve. cheers
@masonroberts70732 жыл бұрын
Put it below if you want to isolate to the both kitchen tap and out door tap. Or place it above if you want to isolate the out door tap
@liamtaylor51222 жыл бұрын
@@masonroberts7073 cheers mate. only took 6 month to get an answer
@daydream6052 жыл бұрын
@@liamtaylor5122 lmfao
@marksn40202 жыл бұрын
I would of liked to know how to work out how much copper pipe to cut to add to the push fit. I think you measure from a certain point on the push fit but i would like to see it done
@joshuasquashua1999 Жыл бұрын
Easy way to work out the x-dimensions: push some pipe in the fitting all the way and mark it off where it just comes out the fitting. Measure that mark to the end of the pipe you pushed in (let's say you measure 10mil for the fitting you're using). Now measure the entire length of the fitting and take that 10mil from the x-dimensions off twice for your new measurement (once for either end, so 20mil in total in this case). When cutting the pipe ready for insert, measure and mark off a section equivalent to the last measurement you took of the fitting with the x-dimensions into account. Cut it out and it should fit perfectly. In the real world though, once you get doing it - being off a couple mil is fine. It's worth being timely for the sake of not being 100% exact if the work is still of good quality. Often pipes can have a fair bit of give so you'll just be able pull them a bit into place. I don't really ever use push-fit though so I'm not sure how much stress they can be put under before the teeth inside start to fail but a soldered joint would hold absolutely fine if pulled a mil or two either way. I hope that gives at least some explanation 🙂
@marksn4020 Жыл бұрын
@@joshuasquashua1999 thanks so much for the comprehensive explanation. Really helpful
@salerio61 Жыл бұрын
I'd have gone out right from the cold pipe rather than left and then you're not tangling up with the hot pipework.
@PlumberOntheJob Жыл бұрын
Well not going back now think it was 12 months ago 😆
@antoniogalluccio42132 жыл бұрын
How can someone run a washing machine flexible hose through the brickwork without even sleeving it?
@ToyGirls_UK2 ай бұрын
How much isit to get somone out to do this and install one ?
@yusifmothanaobadi6017 Жыл бұрын
I’ve installed the tap but there’s not enough water pressure coming out for some reason, it’s weak
@fredjoyce49143 жыл бұрын
Very nice install where do you get the back plates from ?
@PlumberOntheJob3 жыл бұрын
They’re available any DIY store or plumbers merchant
@alidin20132 жыл бұрын
@@PlumberOntheJob by
@Exodia1986Necross7 ай бұрын
I believe you should’ve soldered here , because push-fits tend to fail on the long run.
@stuartday18762 ай бұрын
You can't solder when the stop tap is passing. As a bare minimum he had to use the plastic tee. Could've soldered the rest, but the cost of the 2 plastics fittings is not really significant. Really needs a check valve though.
@cradleygirl2 жыл бұрын
What if your sink isn’t by the window , we have a new build and our sink isn’t by the window and have a radiator by outside wall thanks
@tPowelly Жыл бұрын
Where can I buy that tap and the plate from
@Jamojamo101 Жыл бұрын
Screwfix, for about £15. Get the double check valve tap.
@SmokeyMcPot42087 Жыл бұрын
Why not solder?
@tradwifeuk2117 Жыл бұрын
Drill sizes would be useful.
@PlumberOntheJob Жыл бұрын
A huge one 16mm or 22mm
@samuelmcintyre37802 жыл бұрын
He has a phone in one hand and plumbing in the other what is he
@ukvideosjeffery90163 жыл бұрын
That’s no socket for the washing machine it’s plugged in on an extension wire and who has a boiler in the bathroom what would you do if it’s to hot and want to take the heating of and someone is inside doing the shit😂😂
@engchoontan8483 Жыл бұрын
Imma thinkin of the conflicts countries have due to their conceitedness leading to the many disparate gauges and then promote rules based new world order. Lets get started with damn politicians by asking them to standardise all their toilets(water closet) to the garden gauge and taps and fittings and fixtures. This is what i am thinking of doing to the mixer tap in my toilet. Garden gauges and removeable quick releases. Kitchen sink tap bottom screw-clamp i found for top bottom hand tighten sandwich.... need to hunt slowly for next round.
@engchoontan8483 Жыл бұрын
Not resorting to tap-and-die...
@memememe2674 Жыл бұрын
Here coz I need a garden tap fitted and quoted 200 pound, so looking at why so much, looking at this I hope t hg e guy I get dies a better neater job!
@OldManRik Жыл бұрын
I never understand why people think silicone is so important. Yeah put it in for sanity but do people think they don't have holes in their brick work all around their house? And do they think if the one hole you made for your tap is the one that's going to make the brick work fail or allow water ingress? Reading the comments anyone would think it's a bad job just because no silicone... it's like the least important aspect 😂
@tolgawalsh7774 Жыл бұрын
Forget the plumbing job .. the state of that house. How can you live in that