P0192 Fuel Rail Pressure Sensor Replacement Mazdaspeed 3 6 Mazda CX-7 2.3

Рет қаралды 12,461

Күн бұрын

Пікірлер: 37

@alahrixconsulting5790 Жыл бұрын

I had this same issue and replaced the sensor with the same Bosch part. It worked well for about a month and then the code came back. I hope you have better luck.

@Meanmachine.ms3 Жыл бұрын

Thank you for letting me know , it’s been two weeks so far , and I haven’t had an issue with it whatsoever . So I’ll keep you updated if any changes has occurred in the near future .

@Redmopar83 28 күн бұрын

Thx brother have mine change in 20 min because of your vid🫡🫡🫡great job

@Meanmachine.ms3 26 күн бұрын

Thank you so much , I’m very happy to hear that 🙏😄

@verbotenaim4843 11 ай бұрын

Good Stuff, My dumbass over tightened it when I did this a while back and ripped out the threads. Glad yours came out well.

@Meanmachine.ms3 11 ай бұрын

I’m so sorry to hear that it happened to you . I was very careful when fighting because of how the sensor was small . And I appreciate your support .

@sidewinderfitness 6 ай бұрын

Thank you for putting this up, my brother! You made it look easy!

@Meanmachine.ms3 6 ай бұрын

You’re very welcome . I hope this helps .

@pawadrianlopez6522 Ай бұрын

The smallest sensor works, but not 100% , so you need yo use the same as the oem, it happend to me working on mazdaspeed3 and a cx7 2.3 turbo!

@Meanmachine.ms3 Ай бұрын

It’s been more than 10 months I’ve had the sensor installed , and I haven’t had a single issue whatsoever.

@hibahfallaha2280 Жыл бұрын

Very good work

@Meanmachine.ms3 Жыл бұрын

Thanks a lot

@jaikou5132 9 ай бұрын

Bosch part failed on mine and went back to oem. I would recommend just unplugging the negative terminal on the battety while you replace the sensor. Theres no need to pull and fuses.

@Meanmachine.ms3 9 ай бұрын

Thanks for letting me know and I’m sorry that your part has failed. I’ve had mine installed since January, so it’s been more than 4 months and the car is still running strong and I’ve had zero issues whatsoever. The reason why I pulled the fuse is to make sure that there is no fuel in the fuel rail and no fuel leaks when removing the sensor. That’s all.

@pirategmunger 10 ай бұрын

Any update on this repair? Did it last? Any leaks developed? Did yiu confire actaul FPR with desired FPR?

@Meanmachine.ms3 10 ай бұрын

I’ve had this sensor for more than 2 months , and the car is still running with no check engine lights whatsoever. There is no leaks at all , I check it every week on a Saturday morning, and the car starts with no hesitation.

@kevinaubrey9849 8 ай бұрын

So yours has been fine? No whistling noise or not able to go over 1500 psi on your hpfp (issues i had with mine) I tried 4 different sensors including 5053 and none worked, different issues with each. The only one that would work is the oem 5006 sensor, had to buy a used oem fuel rail to get the sensor. These cars are weird sometimes.

@Meanmachine.ms3 8 ай бұрын

I’ve had the sensor installed for more than 5 months , and the car is still running with literally no issues whatsoever. No leaks at all , no hesitation at all , and no check engine lights or codes. I’m not sure why I’m receiving a lot of complaints regarding this sensor, but it’s been working fine with me . If it doesn’t work for you , then yes try to find an OEM one that’s been used. Dealerships will try to sell you the entire fuel rail with the sensor , they don’t sell the sensor by itself unfortunately. I’m sorry you had to go through this brother .

@x-sir_bully4664 11 ай бұрын

Is still working great the sensor?

@Meanmachine.ms3 11 ай бұрын

Yes , It is still working , running strong , and I’ll be uploading another video this week.

@angeluscollective 11 ай бұрын

How's it holding up? Is it leaking? Has the car still been running strong?

@Meanmachine.ms3 11 ай бұрын

Yes , the car is still running and holding strong . And I will be uploading another video this week as well .

@angeluscollective 11 ай бұрын

Thank you! I plan on buying the part later today

@Meanmachine.ms3 11 ай бұрын

@@angeluscollective that’s awesome. Hopefully you find this video helpful

@cyraxkkcb2mo10 Жыл бұрын

Have you cleaned your maf senor

@Meanmachine.ms3 Жыл бұрын

Brand new MAF Sensor from Mazda was installed 10 months ago.

@augustowiak1 6 ай бұрын

Great vid. Part number not in stock :(

@Meanmachine.ms3 6 ай бұрын

No worries at all. eBay sells them as well. Make sure to enter the exact part number that’s on the sensor. There’s loads of them.

@augustowiak1 6 ай бұрын

@@Meanmachine.ms3 thank you sir

@shesdemonic4449 2 ай бұрын

hey man, remember what you torqued this to?

@Meanmachine.ms3 Ай бұрын

There isn’t a specific torque spec from Mazda. However I tighten it as much as possible by feel . And I haven’t had a single issue .

@Dan-vt1qt 9 ай бұрын

Me second gen when exit a corner or getting on the highway right after a hard turn if try to accelerate hard it just bogs out, then just acts normal, sometimes it does it on the straights too, I change that sensor, change the high pressure fuel pump,clean injectors..... sometimes i think n theres something on the fuel tank...