P0601 again? Check these before you install another PCM

IFollow me on Facebook here: www.facebook.c...
PT Cruiser Overheating? • PT Cruiser overheating...
PT Cruiser Overheating Part 2: • PT Cruiser Overheating...
Info from engineers suggest a few things that can cause the P0601 fault code. Simply replacing the PCM may not be enuff ..Listen to suggestion from EZTZ ASE Certified Chrysler Master Tech

[@packrat9433]

I rmoved a sensor under my air intake on Dodge 20012 RAM. Cleaned its connections and the female recepticle with Electronics cleaner without pulling the sensor. Drove 20 miles, got a P0601. 601 would not go away. I reseated the connection on that sensor 10 times, did a little hookey jukey dance, disconnected the hot wire from the battery for 15+ minutes. Abrasively cleaned the battery terminal and connector. Powered up, Cleared codes w a scanner. Drive for 15 minutes - P0601 gone. Success! I am left with the original code P0138., which is to be expected, 601 clear. Now, back to the real issue.

[@doorgunnerone]

Thats more that I didn't know. Thank you for the info brother

[@l.a.raustadt518]

My 01 Dak has a P0601 been on 8+ years , 1 small piece of black electrical tape in play.BUT glad I found your advice excellent , Thanks for posting!

[@OnlineMechanicTips]

lol,,,black tape,,,lol The good news is a used PCM is plug and play so just swap and go if you find a cheap used one.. Please subscribe to the channel

[@GiorgosC-rp5ms]

@@OnlineMechanicTips the 2001 dakota 3.9 doesnt need to be programmed?

[@OnlineMechanicTips]

@@GiorgosC-rp5ms Hey buddy, can you please subscribe to the channel? Im trying to get it to grow, thanks. Now, If your KEY is black, that means it do not have security sys equipped which means you DO NOT have to get it programmed..

[@ibrahim7933]

Hi, I have Malibu 2013 and the code P0601, but the problem is that the gear while driving, the tiger changes from 5 to the last tiger and it is fixed until I stop the car, turn off the engine, and then the interlock system returns, but the code P0601 remains visible. Any advice?

[@KB-uv7wj]

Man, you've said things which are so real. It's exactly the problem I'm having.

[@powerofknowledge7771]

What a bout a place like Flashmasters who preprograms the PCM before sending it to you? Like a Plug & Play? Have you ever tried a place like that?

[@gerardopule539]

What could be the problem on a Chevy impala when im driving it suddenly dies it turns of

[@stripecatflippangitnamecha8721]

hey Bro is T&W 2001 Plug and play?

[@coryleavitt1534]

I have a 2006 Malibu 2.2l does it need to be reprogrammed or is it plug and play

[@OnlineMechanicTips]

Hello Cory, im almost certain it depends on if your car equipped with a factory aarm sys. Thanks for watching.

[@bubbastacks.9998]

Most dealerships will not flash a new program onto a new or refurbished PCM unless purchased from the dealership if you get it from AutoZone or O'Reilly's they will not warranty it if you purchase the new PCM from the dealership they will flash it with the new program and they will warranty it

[@isrealperez9069]

sorry buddy you can only take it to someone that knows how to program there's a lot of people besides the dealership

[@tomwolf4609]

Good info...good job

[@lajuanwardlow768]

Great information bro

[@johnappleton9349]

went to the junkyard and swapped my 05 colbalt pcm. works good. cut was shutting off 10 plus times a day while driving, now it doesnt.

[@OnlineMechanicTips]

That year was plug and play, there was no need to get it programmed to you car..Thanks for watching and please subscribe

[@Ljuan4212]

Really its just a plug and play, im having the same issue, car shuts off out of nowhere

[@OnlineMechanicTips]

What kind of car? Year, make, model?

[@601carter]

Is the 06 colbalt the same way

[@stripecatflippangitnamecha8721]

Hey Bro I need help, Is TW 2001 plug and play?

[@patrickhamilton1617]

Mine start right up but I'm getting that p0601 code it misfires and burns a lot of gas I thought it was my oxygen sensor but there's no code for it eBay has them just send me your VIN number and they will program all you have to do is plug and go

[@OnlineMechanicTips]

cool

[@Brianvenzor21]

You talking about the oxygen sensor¿

[@Brianvenzor21]

Bucause my 01 pt cruiser 2.4 naturally aspirated misfire and burns a lot of gas too idk what to do or start looking on the engine bay

[@samueladams2649]

After replacing the PCM will it start

[@OnlineMechanicTips]

Depends. A bunch of self test and configurations will have to be verified before starting can happen

[@davidfusco6600]

Thanks, right to the point.

[@OnlineMechanicTips]

Some years are plug and play and will simply work with any programming. Its the newer cars that you cant swap controllers

[@maggiesreviews7994]

EZTZ Rideshare/ News/Auto/Fitness/Multimedia i have a 2001 chrysler mini van. Does it need programing

[@hajrudinkavazovic2231]

What's about main fuse box 🥴😊

[@ceceliasalinas8594]

Hey quick question would you happen to know if a 2007 Chevy pcm or ecm have to get reprogrammed?

[@ceceliasalinas8594]

Thank you in advance

[@ScootinIsLife]

Even if it is Plug & Play you still have to program your key, fairly simple process @ home !

[@OnlineMechanicTips]

Now just how simple is programming your key at home dude?

[@megantippit3668]

YOU DO NOT HAVE TO TAKE YOUR CAR TO DEALER FOR REPROGRAM THERE ARE PLEANTY OF SHOPS OUT THERE TO PROGRAM YOUR CAR LOT OF THEM WILL COME TO YOU

[@OnlineMechanicTips]

The only way ANYBODY can gain access to Chrysler programming is if they are an employee of a dealership or if there shop has a subscription acct with chrysler..Now the older cars, sure thats possible..Unless you have a SID number theres no way to get in sir..

[@S....]

@@OnlineMechanicTips There's lots of workshops which can program PCM.. There's even those which will program PCMs, send it too you and you only gave to plug it in.

[@OnlineMechanicTips]

those workshops you referring to have a subscription acct or a chrysler employee there with a SID number

[@S....]

@@OnlineMechanicTips Not necessarily, workshop I worked in was doing it and we didn't have any subscription nor an chrysler employee. But even if that would be the case, how does it make a difference from a customers point of view?

[@OnlineMechanicTips]

it doesnt..all the customer want is it fix..I was at the Chrysler training center and the teacher made clear of being able to program computers..He assured me without a SID number, theres no way to even log in to perform the program..Somebody somewhere just simply using somebody access..Im sure the customer dont care about any of this like you mentioned.lol

[@peacedixis83]

Hello sir. I have a check engine problem with the engine light on the board. after diag 1 fault code p0601 present. my car is a 2001 pt cruiser 2.0l petrol. is there a problem with the connection fuse? I do not know. what advise me please

[@williamandkathleencasper4958]

I have oil in the wiring harness I cleaned it as best as I could changed out the computer and had it flashed also replaced oil sending unit but still getting oil through the wiring harness car is in limp mode and I can’t get it out tryed resetting the battery nothing also replaced the Tcm I have one code p0700 anyway I can replace the wiring harness coming from the computer?

[@OnlineMechanicTips]

Hello my friend, this is not good. Ive only had luck once with problems like this. Possible the oil has saturated the wires and the circuit currupt the modules.. Its simple hard to recorver from such damage. BTW what year is the car? also are you subscribed to the channel yet?

[@williamandkathleencasper4958]

Online Mechanic Tips it’s an 02 pt cruiser it’s got 134,000 great car aside from this issue yes I will subscribe

[@OnlineMechanicTips]

@@williamandkathleencasper4958 If the oil made it to the PCM, Its very hard to recover if it hits the PCM circuit board. Watch my other video on this here: kzbin.info/www/bejne/bKa4pGpvfJmjfMk

[@MosesJesusElijah]

Did you mean oil in the wiring harness going to the pcm or the wiring harness that connects to the oil sending unit?

[@brandonwilliams9597]

My 2001 caravan won't start. It sounds like its close to starting but just wont. I put a new battery in it and hooked it up to a code reader and got p0601 pcm needs replaced and reprogrammed. Although I seen this can keep a car from starting sometimes a car can run with this error. Any ideas? Could it be a fuse? Im planning on ordering the part tomorrow and just wanted to see if any automotive savvy ppl had any suggestions

[@OnlineMechanicTips]

lol, Jungle Lion, surely you not saying Ford or Chevy have no problems...And just because you had a bad experience at the dealer dont mean any body else would. I suggest to take your PT to the dealer to get diagnosis right the first time, they not junk cars, just sensitive..lol

[@brianthomas5798]

Have a 2001 PT Cruiser and I’ve even chasing overheating for a minute. Is a hand-me-down that had been overheated to shutdown and now experiences other issues now as well. Think perhaps the dreaded head warp

[@patrickhamilton1617]

Lifetime warranty eBay for 250 plug and play

[@OnlineMechanicTips]

O cool, but careful with those on the second gen platform. Please thumbs up the video and subscribe to the channel, thanks

[@thisperson6655]

dodge ram 2001, 1500 v6 3.9L , what is it called? pcm, ecu, ecm? Is it inside the truck or under the hood? Does this one need to be reprogrammed if I get a new or used one?

[@OnlineMechanicTips]

Hey buddy, can I get you to subscribe to the channel to help it grow, thanks..Look, that year truck controller was called a PCM (Powertrain Control Module) and its located under the hood on passenger side firewall.

[@soyeldiego86]

@@OnlineMechanicTips is that 2002 dodge ram 4.7 also plug n play? - I have a black key with no theft system

[@camperjdcamperdreborn7160]

Omgawd - I've never heard someone repeat themselves so many times. Eventually that's the only thing I hear.

[@OnlineMechanicTips]

You on here complaining about a 5 year old video? I didn't even no how to do videos back then. Awful petty aint you?

[@markboyer3391]

2002 Dodge Durango RT 5.9 PCM bad, does it require to be programmed my VIN# to properly function and remote lock FOB work?

[@OnlineMechanicTips]

Depending on what kind of key you have. The PCM will/may have to be programmed to your security skim module. Hey please subscribe to the channel for me, thanks

[@adampurkey6565]

Bro the battery shit worked o my god I was shaking I was so pissed at this thing

[@OnlineMechanicTips]

thanks for watching, please subscribe to the channel for me, thanks

[@keithhicks3262]

I got a 2001 dodge intrepid is it plug and play

[@OnlineMechanicTips]

Hey buddy, can I get you to subscribe to the channel so I can gett to grow? thanks. Now, if your key is black, yes its plug and play..If your key is gray/silver then no, it will have to be programmed. Thats because you car is equipped with sentry theft sys. So your key/skim will have to be married to the used PCM

[@frankmorgan5234]

Please get to point quickly!!!

[@OnlineMechanicTips]

The mere fact you would comment that tells me you should not even be working on the car..you have no interest in understanding what you doing..you just want to dive in and replace parts..smh

[@AllionaViscante-of8ps]

Diko maintindihan haha