Paddleboard inflation part 4, I got myself a Ryobi One+ inflator, is my search over?

Another step in my search to find the method of inflation that best suits me
I got myself a Ryobi inflator which has a high volume low pressure connection for airbeds etc on one end and a low volume high pressure car tyre inflator on the other end
Well the good news is it took me absolutely zero physical effort in terms of pumping
The bad news is it took half an hour and that was casually ignoring the operating time recommendations in the manual.
Is my search over? Maybe not quite although between this and the Michelin tyre inflator I reckon I could get on the water in about 20 minutes so it’ll do for the moment
For reference I’m inflating a RedPaddleCo 11’ 3” Sport which is 258 litres volume (according Red’s site) and I’m inflating to 20psi
Separate review coming on the Ryobi as a tyre and airbed inflator
I have seen "proper" SUP inflators on youtube so I'll look to getting one when I can afford it and do a review
Ryobi One+ inflator - purchased from Amazon
amzn.to/2ZblWgu
redpaddleco isup electric pump adaptor - purchased from SUP INFLATABLES
supinflatables.co.uk/red-padd...
Check out my website www.oldmanwith.com for more Ryobi One+ reviews and DIY info
Filmed on an iPhone 6, Samsung Galaxy A51 and an Akaso EK7000
Edited on an iPad using Lumafusion

[@shawnna1606]

Ty for taking your time to do this. It has been a huge help in the decision process.

[@sincitydude7296]

I just bought that ryobi for my paddle board. Glad I saw your video because I'll be returning it today. Thanks

[@matthewhill6443]

Thanks. I was just about to buy, but... you saved me a $100 and some lakeside disappointment. Thanks.

[@peterstrautins9825]

This video exactly answers my question on buying portable ryobi inflator for sup. Thanks!

[@AlbertPalmer]

Really useful! So glad I saw this, thanks

[@MikeJordanUnCamplicated]

I use the ryobi also. I got a valve adapter for the low pressure side. I connect to the low pressure hose with a short piece of automotive heater hose. No holding required. And when you can let the valve operate, you don't loose any air removing the hose. Which makes the high pressure go quicker.

[@UltimateFifthScale]

Good video thanks. was looking at getting one of these but that's far to slow. I have been using a cheap 12v airbed inflator to do the low pressure part and a Viair 85p 12v compressor to get up to full pressure (usually 20psi) the Viar is rated at 1.26 cfm @ 60 psi. It has been in use for 2 years now, pumping up 2 12'6" touring boards in a row without any issues. A battery powered solution for when away from the car would be ideal but I guess this isn't it. I need to find a waterproof battery pack that can supply the 15 amps to run the Viair.

[@edevans5991]

I just got this inflator and it works for what I need on my kayak since it is the low pressure bit that I find tiring when pumping by hand. What I do is use the hose from my hand pump to lock into the valve and then hold the the Ryobi's tube to that. I'm looking for an adapter to simplify things slightly. I also liked using the deflation. Made it easier to pack than deflating by sitting on it.

[@cameranmanner4701]

i have the same setup, took me 7 mins to fully inflate. I used the hand pump for the final inflation stage. I inflated to 12psi

[@EmmeryCheung]

I have this inflator and only takes me 5 minutes to inflate my kayak to 10 psi. I think the issue you're having is you're losing too much air pressure on the high volume side because you don't have the proper adapter. The first few PSI takes the longest so you can cut a ton of time if you can pump it more on the high volume side. You can actually buy an adapter or 3d print an adapter for the high volume side which will fit properly and give you as much pressure as possible before you switch to the high pressure side. Also I think this pump has a Duty cycle of 5 minutes (not sure exact time) so you're wearing it out early if you leave it running for longer.

[@zhrob1]

I am wondering if the high volume low pressure connection would work for a low 3 psi inflatable kayak ?

[@sQriLLah]

I have exact same pump setup as you. After i fill low pressure volume, i then attach high pressure adapter. Now my ryobi will not engage. I set the high pressure to 15 psi and turn on but nothing happens, not sure why.

[@adamwalker7338]

Full inflation of ???? How many liters (volume), pressure?

[@CraighalbertChurch]

Why not make the high pressure side put a Paddleboard attachment on

[@heresmyopinion4786]

Have you found an inflator that actually works efficiently?

[@notmychannel8602]

Holy crap 33 minutes. Do yourself a favour and get a paddle board specific pump. Mine takes 11 minutes to pump a Red Paddle voyager that is about 350 litres in volume compared to your 250 litre board. I can’t legislate for the extra time faffing about though.

[@waynekill3044]

boars and pump both a waste of time