Ford E250 transmission 4R70w replacement

[@frankvellozzi6438]

Thank you for your straightforward and no-nonsense r&r of the transmission. I did it the same way on the ground with a trans jack I sent the unit out to be overhauled. I saved myself a bunch of money by doing the swap myself. Great video.

[@alltsab]

You welcome

[@jean-pierrehall2914]

Peace FV. In the process of doing this once transmission gets here. Anything unexpected or was yours straight forward as in video. Peace

[@everettmusicdojo]

Awesome video. I can feel the dust falling in my eyes when you take of the driveline bolts.

[@craigelectric5241]

Safety glasses 🤓 a must Up underneath or you regret

[@stevencute43]

Excellent video. Best transmission video I have seen. Thank you.

[@alltsab]

Unwelcome

[@aidanwilliams78]

Very helpful, thank you, did not realize you could remove metal bar under transmission

[@andrewcraig3960]

Great Video! Only suggestion is to mark the drive shaft/U joints link-up because the drive-train is actually balanced and must be put back in the same way it came out!

[@jaredmayer3960]

You’re full of shit. Balanced is balanced. You can put it back in however you want.

[@miketo5828]

Great tutorial and tips. "WELL WORTH WATCHING" this tutorial guided me in changing my transmission on a 2003 Ford E250, everything he says and shows is worth the time to check out. Honestly, it was an easy fix, I would do it again.... to drain your transmission fluid completely, you can just blow into one line and catch the fluid in the other, doesn"t need much pressure, thanks again, All Tsab, stay safe

[@alltsab]

Thank you for your great experience with my video. Don't forget to like share and subscribe. Thanks again

[@jean-pierrehall2914]

Peace Mike. I’m about to tackle this in my ‘11 E150. Anything in particular to look out floor?

[@miketo5828]

@@jean-pierrehall2914 it was easy on my e250. Take off the trans able. Balance a jack on the transmission,, i tied a thick wax rope in front and back of transmission, it was heavy, and lowered jack, and adjusted the ropes as i lowered it to the ground. Don't go under trying to hold that weight, it's awkward and heavy. I went to harbour fight tools and bought the log lift used on a pickup, also i bought the motor holder, I think both were like $150. I put the log offer on the motor stand, strated it inside the van, like a engine hoist, i strapped the transmission on with strapping, and hooked to the hook on the log hoister, slowly jacked up, until i line up the pins that are on the transmission. I also bought 2 long bolts, same as the transmission bolts, to help me line up and slowly bring the transmission to the engine. Honestly, i did it by myself like this, it wasn't too bad. If you need more let me know, sorry I just saw your message, Mike in RI

[@miketo5828]

@@jean-pierrehall2914i tied 2 waxed rope, one in front one in the back as to balance, and won't drop abruptly, it's heavy. I had a jack all the way up under the transmission pan, and slowly lowered and adjusted the rope. Of course all this was after the shaft and selector was removed, be careful with the selector, it's brittle and can break,. But it's cheap on ebay. Measure the length of the cable in case it breaks you have the length. You lower and raise the same way for safety, it's no too bad

[@scottfabino457]

dude I WANT TO THANK YOU MAN TO MAN YOU ARE A MAN WHO MAKES MONEY WITH HIS HANDS AND U HAVE A SKILL SET OTHERS ARE JEALOUS OF. I BUILD HOUSES AND CAN DO EVERYTHING BY MYSELF WITH MY HANDS. YOU HAVE SAVED ME MONEY BY TAKING YOUR TIME TO SHARE KNOWLEDGE WITH ME. I NOW CAN REMOVE A TRANS FROM AN E150 YOU TUBE HAS LITERALLY MADE ME OVER 40K EASY BY HAVING DIY VIDEOS FROM PEOPLE LIKE U. HELL I JUST MADE 5K DOING A PLUMBING JOB AND ALL I DID WAS PUT IN A BACK FLOW VALVE NEVER DID BUT I WATCHED A VIDEO FROM A GOD SENT SKILLED MAN HEKPING PEOPLE LEARN MAYBE NOT ROCKET SCIEMCE BUT LET ME WATCH YOU TUBE I WILL DO BRAIN SURGERY TOMORROW. U NEED ANY BRAIN WORK DONE...LOL..KUDOS FROM CHICAGO

[@alltsab]

Lol yeah love you to share and support to subscribe 😄 to my channel ok thanks buddy.

[@Handyman247llc]

Thank you for the video, my tranny rev just went out last night, overdrive is out too. You are correct there are not many videos on the Ford E250.

[@alltsab]

Unwelcome

[@theapplianceguru]

How many miles on your van?

[@jean-pierrehall2914]

Peace again Brother. I noticed that you only jacked up the front of vehicle. Was it more difficult with the angle of the vehicle higher than rear? I’ve watched the video several times and your confidence and ease of work are admirable. Peace

[@alltsab]

Actually if you have an adjust tranny jack it very easy even angle still easy because this van have a lot room from the top.

[@FreeRangeNomad]

Great video ! Been a long time since I had to replace a transmission in a vehicle. Now have to replace the one in my 1998 e350 van with 7.3 diesel. Thank you ! Your video helped refresh my memory.

[@alltsab]

You welcome buddy

[@jesustorres-kj7sc]

Excellent video. Don’t forget to flush the cooler lines!

[@joshmurray7775]

Keep em coming!! I need a transmission!!

[@jean-pierrehall2914]

Peace my Brother. GREAT JOB. Toal time it took removal and installation. Keep up the GREAT WORK. Peace

[@alltsab]

Thanks ✌peace ✌

[@Greystone76]

Thank you for showing this! I’m a KZbin mechanic and is looking how to get the transmission off the block

[@eweller4243]

Nice Job, Good video and explanation ! Thanks

[@treelife365]

Nice video - it was very relaxing to watch!

[@alltsab]

Thanks buddy

[@timweidner3335]

Helpful video! Looking for something to indicate the level of complexity for a 95' E-150 Econoline 6 cylinder trans replacement.

[@alltsab]

Very ez one

[@peterboytchev6899]

Thanks so much for posting this video comes very handy

[@webywebprods8828]

Great video.Thank you. I'll start replace transmission from my truck eE 250 2005 tomorrow. crossing fingers

[@alltsab]

Very easy 👌

[@superdon1chw]

Thank you my brother

[@Ryan-fs8fq]

thank you. i will save a lot of money doing this myself

[@taxslave5766]

Thanks for the video, I think I'll have a tranny shop install my replacement transmission, Whenever I work on my van I always end up with leftover parts, which isn't a good thing!.

[@craigelectric5241]

Good job Brother

[@bajafishin]

Thank you!!

[@KINGRG1]

Great video! Where did you buy that wrench with the 3/8 adapters built in it?

[@alltsab]

Harbor freight

[@DieselMan73]

What brand and model is that transmission jack you use in the video? I would like to buy one to make my life a whole lot easier when removing these instead of a regular floor jack

[@alltsab]

Pittsburgh brand i bought it from harborfreight. This one is the one ton

[@hmooblomlomzemchannel3531]

Zoo heev li os tij laug aw

[@frederick6008]

Found you again. Got a new phone.

[@DieselMan73]

What brand and model are those ratchet wrenches you use in this video. I see one side is the ratchet and the other is the open end ratchet. This is a great video by the way!!

[@alltsab]

It's call ez red

[@aaronlamb5473]

Excellent video.

[@alltsab]

Thanks

[@pvaldeben01]

Hi All Tsab, so I decided to replace my transmission after watching your video, its great. But I stripped 2 of the 4 torque converter bolts. Any suggestions? I think my only option is to use a chisel, if you have any other possible solutions please let me know. These 2 bolts seamed like they where previously removed and tighten and I think they were a little rounded already. Freaking A. Well any help is appreciated.

[@alltsab]

Slide the transmission out and the you have more from to work that bolts. Yes you can used chisel. Prefer air chisel air hammer. At this point will be mess. If your transmission come with torque converter then just cut it off with metal saw and buy new flex plate. Good luck and please help me subscribe I'm counting on you. Thanks

[@pvaldeben01]

@@alltsab Yes excellent idea, the used transmission came with the torque converter so I will slide back and cut off the 2 rounded bolts. I'll try the chisel first, if it does not work then I will do the slide and cut method. Thanks again and I have been subscribed and bell on for all your content.

[@alltsab]

@pvaldeben01 good luck thanks the subscribe 👍

[@timbond8162]

Thank you for the video Good job

[@alltsab]

You welcome

[@chuckdolor1972]

Great video. Thanks

[@jean-pierrehall2914]

Peace again my Brother. I just purchased my transmission. How heavy is it? I know taking it out is easy just lower it to ground. But how did you get the new transmission on the jack? Did you need two people? Thx in advance. Peace

[@alltsab]

Is not very heavy around 150 lbs. I lift the tranny without torque converter to the jack then put the torque converter.

[@dmitrytopuzis9717]

Thanks brother.....good video.....

[@alltsab]

You welcome

[@hunterfontana5688]

I'm having trouble identifying my cooler lines, saw top line should be in coming from radiator, bottom coming from cooler box, however when I run the lines they bind up making me tHInk this isn't the way it was removed can anyone confirm

[@hunterfontana5688]

4.6 v8 2000

[@genesis80247]

thank you for the video

[@alltsab]

You welcome

[@bellasvistas3463]

How long did it take? Mike Bellas Vistas on KZbin I have an E-150 Club Conversion Van

[@alltsab]

If you have air tool or electric tool it shouldn't take more than a day to do it.

[@bellasvistas3463]

@@alltsab Thanks! Take a look at my Van on Bellas Vistas KZbin.

[@brysir]

The 4r70w Fits in my ford 2014 e350 passenger extended? Please let me know

[@craigelectric5241]

I think different

[@nickh.3832]

How many miles did it have when the transmission was failing ?

[@alltsab]

230k

[@nickh.3832]

@@alltsab yikes. My 2000 e450 truck is at 209k and the transmission doesn't feel too great. Thanks for posting this vid.

[@jcrcordova8763]

I have a couple question, you have a social media IG or fb

[@danrice1141]

Is the procedure same for a 2006 e150 4.6L?

[@alltsab]

Yes

[@smms5056]

👍👍

[@AnwarDakhil]

Only. Thing. On camry hybrid abs. Actuator. You never showed how. To rest. System.

[@alltsab]

No need to reset it

[@sombrick0075]

Whom else had to puch the torque converter to make the bolts go all the way in the flywheel to put the nuts ?

[@fongstory3467]

qhia zoo heev os tuaj caum txawb kj lawm os es his tuaj caum koom kuv thiab o ua tsaug