I have an inspection pit just like yours and yes it fills with water. Following with interest 😁
@PhilsWorkshop19533 жыл бұрын
That’s what it’s all about well done it’s good to show failures as well as success to me it shows the honesty of not only the channel but also the maker keep going your doing well
@thebeginnersworkshop30943 жыл бұрын
Thanks Phil. I’m sure there will be plenty more mistakes along the way, but it’s all one journey.
@PhilsWorkshop19533 жыл бұрын
@@thebeginnersworkshop3094 remember there’s no such thing as mistakes there learning curves and we’ve all got our fare share of them lol 😂
@BIMMY24883 жыл бұрын
Good video again 👍. Shame about the results be thats how we learn . It might be worth trying a dry mix of sand and cement 1/1 or postcrete when the water table starts to decrease. Ground moisture will activate the setting process resulting in hardening. Once hardened it will create a better surface for tanking application resulting in a better seal. Once sealed and dried, then apply another mixture of sand and cement 1/2 over the seal to protect the tanking. Or just fill it in 😄 , regardless I will tune in again .
@retromechanic22383 жыл бұрын
Amazing video - I was in this exact situation last autumn. I taped 2 DPM membranes together to line my pit and concreted they floor Little did I realise the tape had failed in places but I cracked on and ignored the fact the ground had little puddlea. Blocked up the walls and low and behold I was left with a swimming pool; especially bad after a stormy night I took the whole lot down Over the winter and just this week I am back on the project. I have done a single liner and some more concrete on that. The hope is it ranked with the liner but if I’m honest it’s tricky filling a hole 6 foot deep walking with wellies in concrete and feeling stones under your heel hoping your not piercing the liner We’ll see - Thursday I play to start blocking. I think slurry is supposed to work well, but does require a dry surface to start with I spent many a night last year staring into the hole at the water trickling in - I think they call it hydro static, it’s a huge amount of pressure based on the mass or something so only a drip will be constant; won’t be able to slurry it when wet. One option is you could line the hole and concrete and then block up bringing the sides in but you have a stronger chance of keeping it dry then
@alicantibhoy3 жыл бұрын
Really enjoying this channel, looking forward to seeing more
@neilwarren35093 жыл бұрын
Saw your comment moment on woodworking Facebook channel . Im also an aspiring woodworker although will be a couple of years before I can get into it as have loads of house alterations to sort first . Looking forward to watching your journey though . Liked the video . Hope it gets sorted ....
@thebeginnersworkshop30943 жыл бұрын
Thanks Neil. Loads of projects to come from shop storage to insulating the workshop. Please subscribe if you already haven’t it would be really appreciated.
@PhilsWorkshop19533 жыл бұрын
Have subscribed to your channel hopefully to encourage you to put up some vids share your accomplishments about your house many would like to see them
@thebeginnersworkshop30943 жыл бұрын
@@PhilsWorkshop1953 I really appreciate it. Loads more videos to come. When I get some free time today I will explore your channel.
@essentialhandyman3 жыл бұрын
Props for showing your mistakes. I'm looking forward to seeing how you get on with finishing the pit.
@thebeginnersworkshop30943 жыл бұрын
I’m going to have another go in the summer and hopefully the intake is less.
@MadeByEarTV3 жыл бұрын
Having underpinned my entire house and built a 50sqM basement alone let me tell you how to do this! Dry with towels as much you can, Quick set cement Mastercrete green stuff to make concrete min 150mm thick, put mesh 4/6mm raised 50mm tamp it flat. Next day or 6 hours later......... KA or other brand filllet seal (rapid rapair mortar) on all wall/floor junctions, ie around all edges, smooth off at 45 degrees with a pipe, then slurry 10 mm up above fillet and all over floor, two coatings.... job done.
@thebeginnersworkshop30943 жыл бұрын
Thanks very much. I’m going to have another go in the summer when the weather is better and hopefully less intake.
@siras2 Жыл бұрын
Exactly!. Unless I missed it, it looked as though slurry has only been applied to the floor whereas ALL surfaces need to covered for tanking to be effective - with special attention to anything below ground level.
@jerrybootneck17363 жыл бұрын
The waterproofing should have been done at the time of construction but as they failed to do it you now suffer their error in construction. Even if you managed to stop the water ingress at this stage it wouldn't last for ever unless you're prepared to spend a lot of money but as you won't be using it then a total waste in my eye. My advice at this stage would be to dig a small sump hole where it is the lowest in your pit and most of the water will run too and drop your pump into it, this way you can run your hose out the garage and just turn on the pump when you need to drain it, you can hold those floats on the pump up for a while longer to get more water out before getting the vac out. Good honest video bud.
@thebeginnersworkshop30943 жыл бұрын
I’m glad I had a go and fairly early on I had my doubts it would work. You reckon it’s worth another go in the summer or would you just fill it?
@flyerh2 жыл бұрын
Are they thermalite blacks? If they are, they are porous and will always allow water through.
@gilberesrepairs8 ай бұрын
What did you end up doing with the pit?
@jamesaitchison86033 жыл бұрын
another interesting video! keep them coming 👍
@cliffy7641 Жыл бұрын
slurry looked to thin 3 parts slurry to 1 of water, not the other way round.
@JM-lk6xl11 ай бұрын
What did you end up doing to fix this?
@silverdragontaylir82523 жыл бұрын
Use hydraulic cement onwalls and floor(sets fast but waterproof)
@eyuptony3 жыл бұрын
Enjoyed. It'll be a shame to fill it in. What about a fibreglass skin? Tony
@thebeginnersworkshop30943 жыл бұрын
I’m going to have another go in the summer. Hopefully we have a good dry spell and I will take a slightly different approach and fillet the corners to reduce the intake.
@keefykeef3 жыл бұрын
That's a shame.... 😟 Do you have a plan for what you're going to try next?
@thebeginnersworkshop30943 жыл бұрын
The company who I purchased the water plug from sent me a replacement for the damaged tub , so I am tempted to try again in the summer. Hopefully we have a dry summer. Worst case scenario I will just do exactly what you did. I am having my front garden re done and I will have several tons of rubble which would easily fill the pit. That would certainly be the easy choice.
@keefykeef3 жыл бұрын
@@thebeginnersworkshop3094 I didn't have the balls to try and waterproof it, I wouldn't know where to start. Good luck with it
@jagboy693 жыл бұрын
Damn! You got an inch of water overnight? How close are you to sea level?? Concrete block is porous like a sponge. Rubber roofing tar on the back side of the block should solve your issue, but this will require cutting back the opening and digging around the pit. Problem is you still have the pit floor to contend with. I am trying to open up my garage floor right now and not create the problem you have. You can bet whatever I build, it will be sitting in lots of thick plastic sheeting and covered with 5miles of tar! I'm on the fence pouring walls, laying block or using 1/4" sheet steel. There isn't much online on this except for basement stuff. Same idea, holding moist wet soil from penetrating a subterranean structure. I'm pretty high above the water table, but rainy weather will leech through soil and travel quite far. If you wanna see what I'm up, this is it. kzbin.info/www/bejne/o6bap3ZrftSNes0 It's going 8ft in the ground in my garage so yeah, I understand the importance of it being extremely dry! Fingers crossed you get this, SUBBED!