Part 26: Cool Trick To Bleed Your Hydraulic Clutch!!

Do you have issues getting air out of your clutch lines?
Is your pedal spongy and not disengaging the clutch?
Are your gears grinding when shifting?
Today, we bleed the clutch on this BMW E24 6 series with some very simple tools and some EASY TRICKS that will save you HOURS in bleeding your hydraulic system - all without having to bench bleed your system before install!
The components used:
TR6060 FabBot Remote Bleeder Line: www.fabbotfab.com/products/fa...
Vacuum Bleeder 25136 with all the fittings: www.amazon.com/OEMTOOLS-25136...
Please consider subscribing!!
kzbin.info?...
Take a look at my growing IG and FB!
/ garageaholic
/ garageaholic
For more information about what I do and who I am, visit:
www.garageaholic.build
E30 & E36 N54 Swap Guides available for purchase!
garageaholic.build/product-ca...

[@briangill4742]

Wow, like another of your followers, I was perplexed and at the end of my tether by the time I watched you video. I have an old Alfa Romeo Giulia Super and I renewed the clutch slave cylinder but none of the standard methods of bleeding worked at all. I had a buddy to press the pedal etc.... but I also have a vacuum gun the same as yours but used in the normal way did not work at all. Watch your video, went back in the garage and sucked air out of the master cylinder as per your instruction and bingo perfectly working clutch. I don't know how to thank you enough because I read lots of stuff on the forums and watched a couple of youtubes without success, so you saved the day!!I have subscribed and look forward to any future time saving videos...many thanks, Brian

[@zkboston617]

This amazing.. you make it look easy.. Thank you for the tips🤩❤️

[@ianmoorcroft3689]

Great bit of kit, Frank

[@johnpalma7265]

Worth a try. Thanks.

[@colinwillox7648]

Love your video !!! Thank you. Been pulling my hair out on the damn master. Can’t wait to try this trick to get air out of top !!! Thanks

[@street_fighter_mx5]

This video is gold😊

[@GenV_Restomods]

I was at the end of my rope and perplexed because this wasn't my first time with this type of hydraulic TOB. I have a SuperCharged Gen V LT4 with a T56 magnum that I was replacing the clutch on. I knew it was a PITA, but was forging ahead anyway. I tried everything, pressure bleeding, vacuum bleeding and even a direct shot with a syringe. Nothing worked, the pedal was limp, no feel whatsoever. I had watched every video on KZbin except yours, then the light went on. Took me 2 times on top and 2 times on the bottom to finally get the bubbles out and get a decent pedal. Thanks very much for showing me another alternative rather than going nuts............. As a side note, you don't need those expensive $400=$500 dollar TOBs, any standard LS1 ('97-2002 Camaro) will work fine with the T56. I paid $54 for a LUK bearing made in Mexico.

[@Garageaholic]

Thanks for the comment! I’ll keep that in mind next time!

[@stardust3958]

This is the way I set mine up after changing the master cylinder but I feel I need to bleed it more cool way of doing it

[@Nico_335i_DCT]

Even on the e36, this is a pain in the backside, without the right tool. Regards, Nico.

[@sollaunika1137]

Can you press the clutch in while it has 20psi of vacuum..will it cause damage

[@mariusluca7080]

From where can I buy these tool?

[@user-hq7ff6kx6b]

Hello, thanks for the video. I have Fiat Bravo 2 1.6 multijet 105hp. From 1-2 weeks I have an issue with the clutch - when I am going on first and reverse gear the car is vibrating and annoying rasping sound is heard on the front of the car. Sometimes I am not even able to shift the gears and when I turn off the car and pump the clutch and then the car start shifting and driving off without vibrations. Could it be a problem with the clutch release bearing? Or because of old brake fluid and air in the system? Thanks in advance!

[@sollaunika1137]

Can you press the clutch in while its still at 20psi..will any damage be caused

[@irishRocker1]

I suspect something like this on my A5. Clutch was not returning, and garage said it had a decent amount of air when they bled it with a "power bleeder". but, a couple of weeks has passed and the it has stuck half way just a couple times. only takes a nudge to make it return but i suspect it will get worse. It seems like a leak somewhere is creating air in the system. does this sound likely?

[@Garageaholic]

Definitely air in the system

[@DanAlejandrino]

Can you apply this same concept to the brakes as well?

[@Garageaholic]

You CAN use a vacuum bleeder for the brakes on each caliper! Absolutely!

[@stardust3958]

Should work all it's doing is speeding the job up

[@2ndProtects1st]

Tiny bubbles in my 🍺

[@polarpopgang6929]

Hope this saves my ass

[@tpswave3452]

you could also try using a turkey basting syringe

[@Garageaholic]

That won’t have enough vacuum to pull

[@michael70h7]

@@Garageaholic lol dude seriously😅