Here’s a tip, use a piece of tig wire or a welding rod for an angle gauge. Bend the wire to the angle that you desire for your pipe and just use it for a go/no go gauge as you’re bending.
@hipairbrush10533 жыл бұрын
How is that done? Not doubting you. I truly want to know how to do that.
@76629online3 жыл бұрын
@@hipairbrush1053 I cannot explain it any better than I just did in the comment that you replied to. If you can’t figure that out then maybe you shouldn’t even be messing with this stuff.
@cammed_chevy9285 Жыл бұрын
Bro u just saved the day in my case I appreciate that!
@peterwilliams4375 Жыл бұрын
That is a good idea. Also, it may be worthwhile to draw a line along the pipe with chalk or other colour that will stand out on the pipe, and this will help to use the square / wire angle, to easily see how the angle is shaping up on the bender
@flubbernugget8888888 ай бұрын
Good tip thanks
@angiesmith91965 жыл бұрын
Your guess is spot on! Using the bigger die puts all the force on one spot allowing walls to collapse. Where as the smaller die buts force on at least two points both of which are where the collapsing of the walls would have started thus preventing the kinks from ever starting. Good find!
@brucegalvante28704 жыл бұрын
I’ve been using harbor freight bender for like 2 years . What I use is a map torch heat up the metal a lil no kinks at all . Also don’t even bother using this bender if you’re thinking of bending lightweight materials , it will just kink and the 2 metal rollers leaves a little mark on the tube . So use at lease 1/8 thick tubing 🤙🏽
@hellapellanyc64658 ай бұрын
Think it would work on stainless 7/8" boat railing? I can put cardboard down so as not to scratch.
@raicesinterioranas1146Ай бұрын
Fombo
@1Chuck4U2C6 ай бұрын
FYI Crisco cooking grease lubing outside of your dyes helps too. Cheap, not expensive.
@dobby158454 жыл бұрын
Watched part 2 of independent suspension build and was gonna ask you a few questions. Clicked on ur page and you answered EVERYTHING in this video....thank you!! I was certain that, if I start doing these builds, I'd be stalled with a thousand dollar tubing bender I can't afford. But apparently this CAN be done. Might take a little longer, but I'm 50....time I HAVE, lol! Thank you 👍
@JBRACINGinc4 жыл бұрын
Glad to help, just take your time with it and it will work for ya.
@JamesDoylesGarage3 жыл бұрын
Amazing how the most simplest ideas can be such brilliant solutions. Thank you so much for showing us this.
@JBRACINGinc3 жыл бұрын
No problem
@genedustin18292 жыл бұрын
I tried this today. It worked with out to much trouble. A couple this I added where. I buffed all of the paint out of the die, noteched a center line mark in, applyed a little axle grease to the die itself and warmed up the pipe with a torch. No flat spots at all.
@baumiiirobert3 жыл бұрын
I have a SuperEgo (high quality Spanish made) bender. Had it since around 1988. I have never had the crimping problem but the bending shoes are a snug fit on sch 40 pipe. there is no play and they have to be lightly hammered off after a deep bend, good quality and snug dies. cost around $500 (special price) in '88. I used it 6 years in a fab shop I owned, the guys made shoes (liners) to fit inside the sch 40 dies to fit tubing snugly for no kink bending of thinner wall tube. With stainless thin wall we often used sand. We bent thick wall aluminum with it for tuna towers on sport fishing boats. I had them make up a different set up, two 6 foot or so long slightly bent and reinforced steel channels (one greater radius, the other less) and used them on the floor with a porta jack to bend slight camber in the tubes for canvas covered tower roofs, that was easter than roll bending, faster and always uniform. we had an angle plate bolted to the floor for the jack base and two vertical pipes on each side about a foot outside the die for wood blocks to rotate on to hold the pipe ends. The depth of the chord on the shoes (dies0 is about 18'' on one and 2 feet on the other. Jacking until the pipe came totally in contact with the die and stopping right there gave repeatable uniform curves. Fast and easy. Shut down that shop in 1996, but still have every machine, press brake (180 ton 10 feet), 1/4 x 12 power leaf brake (both Chicago), 3/8 x 7 foot plate roll, a 1/4 x 10 foot ADIRA shear, a dozen welders (up to 400 amps, several are tig) and all kinds of other stuff spread all over the yard under open side roofing (tropics, central America) for convenience to not have to move welders around, just leads. All for hobby use since '96. At least I am not bored like other retirees. Kept everything, benders, lathe, mill, drill presses. Wood shop. Perfect for any personal project. biggest hobby shop in Central america as far as I know. Maybe there are 6 or 8, maybe 10 industrial shops in all of CA that are better equipped outside the Panama Canal and large shipyard in Balboa in Panama.and maybe not that many.
@markmark52693 жыл бұрын
Respectfully, I disagree. I have been using pipe benders for some 30+ years and I tried all this nonsense, wasting my time and the mess with sand, now I find it very simple to get good bends, and I even build roll cages for race cars with a pipe bender. No kinks, no waves, the rules don't allow that anyway. First, the dies must be spotless and polished. Many are supplied with as cast rough finish, get a flappy sanding disc out and start cleaning, doesn't take long, and that includes the 2 outer roller dies. Second, and important, the 2 outer roller dies are ALWAYS too close together. The bender in the video will need redrilling to move them straight out sideways, or even back towards the ram, or, as experienced in the video, you will run out of ram. I can't tell you how far to space them out, drill a few holes and test for yourself. On the benders that the holes don't go so far forward, I am often 2 holes further out than the manufacturer recommends, but you need to test, just know that further out is better than too close together. I don't know what's wrong with the makers of them, it's like they don't test them themselves. Just some other tips, if you don't mind the mess, use some oil or talcum powder, to allow the tube to slide through the dies as it needs to, rather than the die's surface gripping onto it.
@frankmmiii2 жыл бұрын
Yes, polishing the rollers and dies are also important I believe so you don't have any binding. But I do believe the sand would help to keep your tubing from kinking. I heard that many times especially when using the small hand held benders you bend brake line or very small diameter tubing.
@henrye7182 жыл бұрын
Probably not practical for a home builder who's building one thing. The bending machine will cost as much as the whole project.
@todds59569 ай бұрын
Do you buy chance have a vid of your method? Thanks.
@markmark52698 ай бұрын
@@todds5956 No need, as I said the secret is in polished dies and spacing the rollers wider than you think. I have pictures in a forum I am in, can't remember which one, if I remember I will post the link later.
@garyyorke10805 жыл бұрын
Not a bad result probably the best I've seen without a lot of faffing about or forking out for a JD2 bender .thanks
@billhicksmcgee11814 жыл бұрын
Once you do some bends and figure things out, measure the ram sticking out. This is a good way to repeat bends. I wrote down a key with what ram distance gave me a certain degree. Before jd2, I used to use this bender to do 4130 tubing, just use the die smaller than your material.
@JBRACINGinc4 жыл бұрын
measuring the ram is a big time saver and is something i started to do after this video. maybe someday ill grow up and get a jd2...
@billhicksmcgee11814 жыл бұрын
@@JBRACINGinc don't get me wrong, Chicago's finest bender has done plenty for me, I even made dies to kink flat strip haha. There's a lot jd2 can't do, but stepping on the pedal and doing 2" 4130 is nice. Paid dues there too, long ass cheater bar and grip tape on the floor haha. Keep up the good work jb's garage
@JBRACINGinc4 жыл бұрын
thanks man
@jacksmith30974 жыл бұрын
The trick to no kinks is keeping the sides of the pipe or tubing from blowing out. It you can do that you have won. Great job and cool project.
@joelalleman9591 Жыл бұрын
they look like some pretty nice ,kink free bends !!!
@sipthewater3 жыл бұрын
I use and re use sheet metal piece to buffer out the die. That way the radius is right and it fills in the loose spots. You can add more sheets if needed. I get perfect bends and no sand, just move the pins in tighter to the next tighter holes.
@radpaul257410 ай бұрын
Thank you for this tip! I struggled to bend before this video!
@lestergillis81713 жыл бұрын
Yes. I recently watched a similar video about the same product. Sand DOES help. However, putting 1inch LATTERAL marks along the pipe, and then bending an equal amount along those one inch marks, allows bending without any pinches and without the use of sand.
@JBRACINGinc3 жыл бұрын
I did try that method and found it to leave little dents in the pipe, the sand method makes a clean uniform bend in the pipe, but that's just my experience with it.
@Jaypeeco2 жыл бұрын
Hello! I appreciate your video. The sand helped me bend a schedule 10 pipe! I do have a tip!. The dies have a couple of holes! Is you bend it past the top frame plate and clear the holes. You will have a perfect 90°
@boots7859 Жыл бұрын
One trick I saw an old timer do was as follows. Tape bottom of pipe Fill with sand, tap a bit to get it to settle and add more sand. Pour a cup or two of water onto the sand in the pipe until you have leaks out the bottom. Tap a far bit and refill with sand. Add water and repeat until its full-full. Tape the other end and bend. Or simpler just add sand and tap and ram the sand until its packed well. Would add water just in case you can get some more settling.
@vietkid707 Жыл бұрын
thank you bro, saved me a lot of money on my projects!
@codyramos32005 жыл бұрын
it helps if you do like 10-15 pumps then move pipe up an inch or 2 do another 10-15 pumps move pipe up inch or 2 repeat .... will keep the pipe from crushing/kinking . the hf benders work just have to be smart with it . small 90 degree radius bends are a issue ..
@JBRACINGinc5 жыл бұрын
I tried that technique and it does work but when i did it i got small dents/kinks on the inside of the bend. I also wanted smaller 90 degree bends for what I'm working on and smooth bends. This was the best way that I have found to achieve that.
@thomasheer8258 ай бұрын
Normally I set the bender on a stand I made for numerous metal fabrication. Basically a spare tire/wheel and a 3" pipe welded to it and a 6" square piece welded to the top. Not a work of art but it works. You can then bolt down the bender vertically, set a level to check. then simply use an angle finder and double the number you see and you have it. Haven't had to use the sand trick yet but it is said to work fine if needed. Want to make some Tubing spacers and a saddle back to bend some steel tube that needs to be sharper than my HF tubing roller can do.
@southfloridagearheads65044 жыл бұрын
Nice! Ive done this trick with copper tubing before, glad to see it works on pipe. I just picked one of these benders up and it kinked the first two pieces, then tried to move the section in one inch increments. still left small kinks in the pipe. going to fill with sand now!
@boriskarloff5983 жыл бұрын
Thanks for the video and sacrificing that 3/4" pipe to show what and what not to do. I'm picking up one of these next week just to do a small project.
@JBRACINGinc3 жыл бұрын
thanks for watching and good luck with your project
@3kmotors4865 жыл бұрын
Thank you for the tip. I will definitely be using this soon. Glad I’m catching your start up on the cart build because I am fixing to do the same but bigger scale. Following for the rest of your progress.
@SystemHacker234 жыл бұрын
I noticed he's using pipes for his go kart build. I thought tubing would be more appropriate..?
@michaelwebb87884 жыл бұрын
About to build a hard tail bobber with my son. I'm going to use your method because I can't move the pipe during the bending process and these results look better anyway. Sounds like a little patience and prep work are the key to good looking bends.
@JBRACINGinc4 жыл бұрын
Absolutely take your time and bend the pipe slowly and you shouldn't have any problems
@koreywilliams4570Ай бұрын
I just bought one of these for a mini trike build I want to start here soon.
@jasonneedham6734 Жыл бұрын
Exactly where I am at. Brilliant. Thank You😊
@ivan-Croatian Жыл бұрын
Instead of a sand inside the pipe, you could also heat the pipe where the bending place is. You could heat it really quick with a gas and then it shouldn't kink the pipe when you bend it. And not only that, when you heat it, the pipe will not be tensed neither.
@joelswan5494 жыл бұрын
Try using a large framing square on the heel side (outside corner) for checking 90 degree bends, easy and accurate
@JBRACINGinc4 жыл бұрын
I have one couldn't find it at the time so I used the next best thing, but I just bought a digital angle finder, you can put it on one and multiply the degrees by 2 and that is the total amount. So if you bend it to 45 degrees on one end it will be 90 total. It's pretty slick.
@JoeNunya-oz1ndАй бұрын
I wonder if using the next die down would have a similar effect by holding the bottom up from being the first point of contact for the overall force? Never used one before and I’m looking to do the same for a project. Thanks for the demo.👊🏾
@robertblackshear89632 жыл бұрын
Good job on the go-cart frame. And given what I'm observing, you definitely know what you're doing.
@JBRACINGinc2 жыл бұрын
Thanks bud
@AntonioClaudioMichael4 жыл бұрын
Very nice informative demonstration video
@gregorytimmons47773 жыл бұрын
Try the other type of bender that uses a bottle jack where the jack pushes against one side of the die bottom and rotates the die with the pipe end held by a u shaped strap bending it around the die as the jack rotates the die thru about 45° as the jack extends. Obviously this type while somewhat similar to yours takes some repositioning in a multi step process to achieve anything beyond 45° or so. A little oil on the pipe and die, packed with sand, perhaps a little warming with a torch? Basically some experimentation in the search for the highest quality bends repeatedly.
@matthewmoilanen78718 күн бұрын
Not to be a Donny downer but you go through all the effort to cap and pack tubes wasting how much for material supplies and time rather than just buy a little bit better bender. This is a ridiculous amount of nonsense to go through that still creates a smashed tube. That is why I saved up for about 3 months and bought a decent bender. Best decision in a long time!
@t.s.racing4 жыл бұрын
Times 2 on the large framing square on the outside of the bend. H-F, around 10 dollars, bright yellow, can't miss them. Good luck.
@wht240sxka4 жыл бұрын
I used to use a piece of fence pipe ripped down the center to go over top of pipe I was bending and had pretty good results.
@Makermook11 ай бұрын
Thanks for taking the time to make this video. I'm going to do a similar project and I was wondering how to bend the pipe without kinking it.
@jedhatcher2522 ай бұрын
I just bought a 16 ton version cause of him. I've been wanting to learn this shit for years.
@tfr64 жыл бұрын
Sand isn't necessary. Bend as you go. Mark every inch of the bend you want and bend little by little. Much faster than sand.
@jeffpatnode74463 жыл бұрын
Can't find your video
@treychastain46862 жыл бұрын
@@jeffpatnode7446 bleepin jeep did a video showing this method.
@jeffreypatnode52542 жыл бұрын
@@treychastain4686 this is good to know
@bracketracer20004 жыл бұрын
great informative video. dudes like you make youtube what it is thanks
@JBRACINGinc4 жыл бұрын
Thanks bud, glad to help
@miguelcarter19494 жыл бұрын
Exactly That’s a old school trick my pops taught me Common sense prevails
@alivenumber5 Жыл бұрын
Could we get tight 180 bends with this?
@ChristopherJones16 Жыл бұрын
Can I get some opinions on which bender is **better** for making motorcycle/ebike frames? This one or the hand wheel rolling one at HF? I see people buying the roller one but have to by the Swag Off-Road upgrades to make it work like a "$1000 bender" as some have claimed.
@hotratz694 жыл бұрын
Never had to use sand with mine, had it for 30 years, makes perfect radius's, no sand. I think you may have started with the wrong die? It doesn't look like your material actually fits the die. Right material?
@georgeowen20833 жыл бұрын
Believe it or not flower works really good it packs tighter.
@richarrrdj Жыл бұрын
You can buy the individual dies from harbor freight parts people. That's for the 12 ton bender.
@N.California11 ай бұрын
I wonder if a person wet the sand while in the tube, if it would make it absolutely compacted and therefore more effective as a stabilizer for/in the pipe?
@rkdev15 жыл бұрын
A carpenter square should be in your future. It's a long "L" shaped thingy!
@JBRACINGinc5 жыл бұрын
lol ya I have one... I was too lazy to go get it out of the basement.
@vaughnbarendregt40797 ай бұрын
Get your welding gloves on and heat the metal, not glowing red (not to lose it’s structural integrity obviously) but hot enough to make your steel soft and malleable. Several benefits from doing so but the main one being less force and more “flow” as the metal molecules spread apart it’ll act more like a liquid and form around your dyes rather then want to fold because of them. Maybe you already thought of doing so but felt it’s worth mentioning, anyway keep up the good work man!
@MrMcbuck483 жыл бұрын
Thanks for the tip, gona give it a try.
@JBRACINGinc3 жыл бұрын
Good luck
@Paladin_of_Justice2 жыл бұрын
You can use card board or a shop floor and draw out degree increments so it can be easier than with just a square .
@boostedgringo5885Ай бұрын
Thank you for the info
@theimpaler23173 ай бұрын
Are you doing this for a 4 wheeler brush guard? I wanna do the same, to build a simple brush guard for a 4 wheeler. And I am doing research, that’s how I ran across your video.
@mecano_s44862 ай бұрын
Bonjour... Si je souhaite cintrer un tube d'acier rond à 90' en cintrage hydraulique du fer, quelle est la distance entre les deux galets pour chaque tube ? ♥
@jeffnations66493 жыл бұрын
Good explanation!
@filmart4308 ай бұрын
Don’t forget that metal has “bounce back” so you might have to go a couple of degrees past your target angle.
@Mikewheeler1312 жыл бұрын
I appreciate it. I buy sand tomorrow lol. I was ready to take it back...
@TrevoPhD Жыл бұрын
Thank you so much man. I bought this bender marked down (returned item) and I was worried it was junk. Seemed like a pretty simple design though, so I wasn't convinced anything was wrong. I saw your video and found technique was the problem -- of course! You're a lifesaver 🫡
@brittanyb8394 жыл бұрын
4:24 "meow"
@daveharley83872 жыл бұрын
Use a large carpenter square and measure on the outside of the bend that might help you out on your angle
@nam1esiw3 жыл бұрын
The word you're all looking for is not downfall, it's drawback. Get a framing square to check right angles at that position.
@davidhauge57063 жыл бұрын
Love to learn thank you
@1956vern4 жыл бұрын
Looks like your doing a good job! I’m glad I seen this! In my backyard I have a four step precast concrete steps! This weekend I’m going to buy a bender! I want a railing for my friends and family! Hopefully it will make it so they feel safe! I had forgotten about sand in pipe! Thank you! Hopefully that suggestion will help me!
@RichardMiller-tq6ut4 жыл бұрын
If you are determined to spend time on sand to save time on multiple bends, freeze plugs are helpful. Really though, fuck sand, move your pipe a half inch every 12 pumps and you will get a nice bend in far less time with no mess. Use a level or mark a line down one side to keep each bend straight withthe next
@bakedpotato8583 жыл бұрын
I did a 90 first try just take your time and move the pipe back or forward like no more then 1/2in or less like 1/4 pump again and I only had to do that once for 90 but might need to do it more often for tighter bends. for 1in and bigger your going to want to by some pipe cut in half horizontally rest the tube in your cut pipe and bend I.D matches the OD of tube to super to make a sleeve or even weld your own die with pipe
@bfoehlinger14615 ай бұрын
I don’t own one yet but I do know 3/4 sch 40 is 1” OD should the bender be set up for pipe od? Or id? Again I don’t own one does the instructions specify?
@GotScout4 жыл бұрын
As you fill with sane. have long rebar inside the pipe... and jamb and exit a bit as you go. That will give you he greatest pack.
@hipairbrush10533 жыл бұрын
How do you get the sand out after the bend? Just push it with the rebar? Seems like it would be too packed ...
@sailawaybob9 ай бұрын
Cool video great tips
@alexandraodinlo27607 ай бұрын
Can’t kink if it’s full. Brilliant
@henrye7182 жыл бұрын
I'd say use a vibrating sander to pack the sand and get out any air pockets.
@mrbig45324 жыл бұрын
Could you heat the pipe up first with a cutting torch then bend it or is that not how it’s supposed to be done , I have bent black pipe around stuff that was in my way and I didn’t have room to turn a fitting to make an offset do I just heated the pipe up until it turned cherry red then carefully with welding gloves on I used the hole in the pipe vice for bending conduit and made a 45 degree offset with a 2 inch travel piece then bent another 45 degree offset back to the original direction I was going
@JBRACINGinc4 жыл бұрын
Using heat with this tool will just make it easier to kink the pipe in my experience.
@mrbig45324 жыл бұрын
JB's GARAGE ok was just curious I’m a plumber/heating mechanic and was interested in a pipe bender but it’s not real straight forward and seems like more of an art which takes a long time to become halfway decent...
@JBRACINGinc4 жыл бұрын
Definitely takes some time messing with it to get it right
@thomasdecker8502 Жыл бұрын
Having a clamp that corresponds with the die will help too
@neonnerd13644 жыл бұрын
Good info. Unfortunately silica sand is outlawed in Ohio where I live. My brother works for an industrial sandblastong recycle manufacturer and even they're not allowed to use it anymore.
@waveaddict22713 жыл бұрын
Quikrete sells "playground sand" advertised for children's sandboxes which is silica sand. They should be in prison for continuing to expose unknowing families to this stuff. Their Safety Data Sheet even lists the known potential for silicosis of the lungs. www.quikrete.com/pdfs/msds-b4-playsand.pdf
@MechInvent Жыл бұрын
That's embarrassing. Don't get sand in your jayjay
@mileswatkins216211 ай бұрын
If I need to angle the left vs right once I have the angles is that possible
@dangatto86662 жыл бұрын
Nice job. If you want to make 2 bends a certain width apart, do you line up the end of the shoe, or figure out the middle?
@JBRACINGinc2 жыл бұрын
I put a mark in the center of the shoe and then I mark the center of the bend on the pipe and line the marks up
@TyroneJose-k7y Жыл бұрын
@@JBRACINGinc hi sir thanks for showing us how it works, can you please tell me if it can bend 2" in pipe 1/8 thick? i want to buy it but idk if it will work thanks you.
@cameron3490 Жыл бұрын
Are you using steel pipe?
@DivineMisterAdVentures Жыл бұрын
Seriously? (Lllllllll) You need to get to a hardware store.
@DontStopBrent3 жыл бұрын
What’s your advice on square tubing? Can you use this bender on square?
@JBRACINGinc3 жыл бұрын
I haven't bent any square tubing so I can't help you out there, sorry
@DontStopBrent3 жыл бұрын
@@JBRACINGinc I appreciate the time you put in on my training. Thx thx!
@mr.sixstring63943 жыл бұрын
My pipe just called me daddy for some reason. Gotta hate kinky pipes am I right.
@jeremyoshea7941 Жыл бұрын
Pretty cool you have a same go kart I have
@hipairbrush10533 жыл бұрын
could you not put a carpenter's square on the outside of the pipe to see if you're at 90 degrees?
@nilla0034 ай бұрын
What about .095", 1" od tubing (go-kart frame)?
@user-qu6jf6ot5o Жыл бұрын
.5 bend looks good
@ShopperPlug3 жыл бұрын
What kind of pipe is that? how thick is the pipe's wall? would be nice if u provided the link to that pipe bender. Wouldn't the sand push out the duct tape as the pipe bends?
@JBRACINGinc3 жыл бұрын
3/4 schedule 40 pipe, the duck tape holds the sand no problem
@area3514 жыл бұрын
No safety glasses? Man you are brave with that Chinesium quality tool.
@JBRACINGinc4 жыл бұрын
I know, I should have had my m95 face mask on too knowing where that came from
@lonestarlows3 жыл бұрын
@@JBRACINGinc actually (2) n95 masks...
@JBRACINGinc3 жыл бұрын
@@lonestarlows lol ya can’t be too safe these days..
@hondafreak86134 жыл бұрын
If the side of the die came up around the sides of the pipe. It wouldn’t kink. The dies are not deep enough to hold the sides of the pipe. That smaller die holds tight on the edges from squeezing out and kinking. I would be welding plates to the sides of the die. It would never kink if the pipe was supported on the sides
@briantruck22843 жыл бұрын
Good point
@microfarmers2 жыл бұрын
I use grease on my bender so the die can slide against the pipe rather than getting bound.
@MrBlackbutang2 жыл бұрын
Never had a problem with kink in one of those.
@omorin342 жыл бұрын
Wasn't sure about the HF bender. You sold me on it and the sand. Hope the Go Kart is holding up well.
@JBRACINGinc2 жыл бұрын
It’s only been wrecked 2 times so far lol
@omorin342 жыл бұрын
@@JBRACINGinc sounds about right.
@autoprime124 жыл бұрын
Thanks for the video...
@JBRACINGinc4 жыл бұрын
No problem bud
@hubertrobinson88258 ай бұрын
It will work with some patience and sweet oil that sand trick really works many yrs ago I was building an air compressor and after lots of ruined copper tubing and frustration I guess a voice in my head said you damn idiot pack it with sand it worked my wife where did I get the idea from my answer was I really don't know but it stuck ever since then
@danvandertorre63493 жыл бұрын
kinda makes you wonder if using the sand is of any use I know its good for thin sidewall pipes
@alt-w71303 жыл бұрын
Have try 2 inch pipe? You can get a test plug from the plumbing store
@witosarlaw4 жыл бұрын
Mantap bang..makasi tipsnya 😁👍👍
@chrispy38664 жыл бұрын
People, you have to not only pack the sand tight, but you have to weld a cap at the end, so the sand braces agianst itself. Duct tape won’t provide any pressure at all. It’s useless what you’re doing.
@dmikeminks97684 жыл бұрын
Use diatomacious earth and ram it (not tapping on the side). Also, use some lubricant on the adapters.
@simonthomas37408 ай бұрын
Thanks👍
@GolfMotionAcademy2 жыл бұрын
Amazing. I need to bend 1in blk pipe to make hand rails
@ricky128112 жыл бұрын
Thanks brother
@stephenrolheiser62617 ай бұрын
thanks for sharing
@j.cleveland90317 ай бұрын
Thank you(I kept kinking it) 🙏💕🌎💝
@notthatdigusted74683 жыл бұрын
Looks like a great tool because I need to bend some pipe to customized my bmx bike frame to fit a motor onto it. Watch Neves Project motorized BMX.