Peterbilt | Steer Axle Repair | King Pin Replacement

[@mr.george-pht]

All the experts make things look easy. This guy has done this more then 100 times I bet. If I did it, it would take all day 😆

[@MarcoHernandez-du6im]

It looks so much easier and better on a truck, I have done a few king pins on a MCI bus and no joy as the whole bus is on top of you, this looks so free and open.

[@chucktaylor4958]

He sure makes it look easy.

[@johnmcgreevy742]

Another fine job there sir!! Thank you, I enjoyed watching it.

[@thealfaman12]

You made it look so damn easy it took me atleast 3-4 hours the time i did it and man this thing was dirty

[@wdobni]

excellent video......good content....excellent visibility....excellent editing

[@6.0C150]

Great video, something I learned that helped me with stuck wheel seals. If you remove the snap ring, leave the circular ring on and loosen the nut, the nut stays contained with the hub, bearings, and cone, also helps pull the seal off the spindle. Only downfall is you cannot suck the oil out of the hub.

[@troyharness7863]

Just done a set last week on a Pete came apart the same way gravy job

[@BonheurEsperer]

Great video!!

[@jeffsnider3588]

You make this look easy.

[@robpeters5204]

From the beginning of this video, it looked like you only checked to see if the wheel bearings had play from the one view. Did you look to see if their was any play from behind to verify it was the kingpin?

[@hindunaik4000]

Excellent mechanic

[@marcosandre-kw2ke]

Muito bom os vídeos não tem enrolação 😃

[@urioropeza7010]

Good job 👏

[@jonasavellan3626]

Excelente 👌trabajo 👍

[@williamlawrence1422]

I have a 2135 ingersol impact if you want to replace that old cp. Do you folks have 2 mechanics on this truck.

[@valenting4928]

Легко вышел,а у нас порой по 3 дня шкворень выбиваешь 😂😂

[@adamprost4037]

How long have you been working on the truck

[@agger838]

How do u fix new king pins that are too tight causing over steering?

[@Randomgdude]

They should be reamed to fit properly when new

[@bvelasco57]

@@Randomgdude or get ream less bushing kits

[@luisalejandronunezmartinez8660]

I learn somethings new for mi work

[@zephyteh2628]

Isn't that checking the wheel bearing play?

[@jlsims1276]

That’s the kingpin?? Man, I thought it was something else and waayyy smaller.. I’m learning. Thanks.

[@raulrojasmendoza5176]

Did he skip the bushings or it wasn't a full video

[@patriciaacevedo4429]

Is that a Rockwell or what?

[@michaelcostner5287]

what about the bushings ?

[@MarcoHernandez-du6im]

That’s a great question, if it doesn’t use any then I’m not familiar with them, the ones I’ve done use coper bushings.

[@MarcoHernandez-du6im]

That’s a great question, if it doesn’t use any then I’m not familiar with them, the ones I’ve done use coper bushings.

[@ckc2002]

Why don't you show putting in the new bushings

[@БорисМ-б9щ]

На КрАЗе попробуй выбить шкворень и поменять втулки.

[@Seveneleven44]

I do not miss turning wrenches on trucks one Bit.

[@48statenomad]

Me neither

[@whoisharo4689]

Thats a rad tool at 7:50

[@lgmorrow1]

you put it together dry, no lube. WHY??

[@ДенисРадин-р5х]

Не показывает как втулки менял в балке

[@fordpowersmoke2725]

I’ve never had one just fall out like that.

[@gregolson1824]

Me either, always have to drill the wedges to get them out. Then torch the bearing and cut the kingpin above and below the axle, pull the spindle then start hammering on what's left of the kingpin in the axle. It's pretty easy if stuff came apart like the video

[@hashanchamika3674]

👌😊

[@elsoncorrea5805]

Boa Noite Rio Branco do Acre

[@doudoumohamed7885]

👍👍

[@carlossegatti2626]

Es facil, si pones todo nuevo,....

[@Bigmike3406E]

It’s time .

[@mullerpascal2222]

👍👍👍👍👍👍👍👍🇫🇷

[@KANGGOOEv94]

That was all luck

[@supernut4021]

Tells us how much drivers dont take care of there truck with small things

[@DavidGurrney7589]

Good video but nothing works out that easy. LET'S GO BRANDON 🚵🚵🚵🚵🚵

[@josephwynn3163]

I'm trying to see why you beat the cross pins in like that, should t have to beat in... The king pin is slotted for the pins