Thanks for persevering when you ran into trouble and it didn't look like it would fit. Its nice to know that things don't always go so easy for the 'pros'. And of course it shows us what to do when we do encounter that situation. Many thanks!
@aaanton11 Жыл бұрын
Very true! Thanks for the great comments👍🏻👍🏻🛠
@dixitapatel42832 жыл бұрын
Thanks for explaining how to insert new rubber seal. You just made my work look easier as I was going to pay some else to do the job for me. Love it!
@aaanton112 жыл бұрын
Thanks for the great comments👍🏻👍🏻🛠
@74HC044 жыл бұрын
Thanks for another great tutorial! I sat on the edge of my seat, waiting to see if you would struggle with excess slack! Been there with the tailgate seal a couple of times and it was a nightmare of a job... Same issue - seemingly too much slack until you reposition it a few times and find the 'sweet spot'. I've even managed to ruin a brand new tailgate seal by tapping it on with a soft-faced mallet. That wasn't the cleverest thing I've done! Being gentle with these is important, otherwise the "U" shaped metal clips inside the rubber channel can get distorted. A common leak with these is supposedly around the bodywork flange. There is a soft white, putty-like, mastic in the rubber's channel which is supposed to stop water wicking through the channel (around the bodywork). When I replaced the tailgate seal, I removed some dirty mastic from the body and gave the area a good clean and dry before fitting the new seal.
@aaanton114 жыл бұрын
Some great similarities in there, its so funny how we all go through the same experiences, I have fitted many seals on different cars over the years but still whether is more than one part available doubt sets in😂, Thanks for all the great information👍🏻👍🏻🛠
@garrynutter8604 жыл бұрын
Nice recovery there mate. well done. Thanks for the measure aswell.
@aaanton114 жыл бұрын
Nearly got the knife out lol, and the big hammer, Thanks for the great comments👍🏻👍🏻🛠
@denniskoenderink48524 жыл бұрын
Thanks for these useful videos! I have a 2014 Peugeot 107 myself so i definitely can use one of them in the future! 👌🏻
@aaanton114 жыл бұрын
Thanks Dennis for the great information👍🏻👍🏻🛠
@IBANEZfil4 ай бұрын
Great video just did this on my Skoda Octavia! One tip I can give is to use some silicone spray. Mine was stubborn and didn't want to fit properly even after some force. I lightly sprayed the inside of the seal and then it fit like a glove!
@aaanton114 ай бұрын
Great tip! Thanks for the great comments👍🏻👍🏻🛠
@frankcoldwell3 жыл бұрын
Thanks for these videos. I first tried the one to gently bend the door back into place and that worked for a while, but now the puddle's back I'm hoping to invest in a new seal and hope that works!
@aaanton113 жыл бұрын
Glad it helped, there is a link in the description to a cheaper on on amazon, Thanks for the great comments👍🏻👍🏻🛠
@1972dazbo4 жыл бұрын
Glad you never cut that seal mate as i could tell it was correct.....all you need to do is push against it in the opposite direction of fitment as you go around to take away any excess. £130 quid for that is a joke and may not be the problem as water ingress could be through the crappy polystyrene seal behind the door card which was the case on my daughters car not the seal. These cars are a nightmare with water ingress as we run 3 of them and done all the usual water leak problems and i am now considering drilling some large holes in the bottom of the doors to stop water building up inside as in the most recent diabolical weather we have had i noticed the doors on my daughters car holding a lot of water inside which you could hear swishing about when opening/closing the doors ? Water was building up and coming through the inner door shell through the polystyrene cover and lapping down the inside of the door with water forming on top of the door seal then running into carpet ? Cured this with some car body seam sealer smeared around the bottom of the polystyrene door cover then replaced door card and all appears good,however still not happy with the water build up inside the doors,hence why i am considering drilling a couple of holes in the bottom of the doors so the water escapes down the outer cills on the car ? what do you reckon....Let me know your experiences with door leaks on these cars as they are a nightmare and the only negative for me owning them,otherwise cracking little motors....currently have a 2010 c1 3-door vtr+ and 2 x pug 107's both 2013 years so all keep me busy ( just put a exedy clutch in c1 vtr last week )....Keep up the good work pal,regards.
@aaanton114 жыл бұрын
Normally on the city bug doors there is are 4 drain holes, not round ones but rectangle ones, I have not experienced water in the doors but if yours are blocked up then that would explain the door filling up, if you look under the door frame it is possible to poke a cocktail stick up the drain holes to clean them out, Thanks for the great information👍🏻👍🏻🛠
@1972dazbo4 жыл бұрын
@@aaanton11 Yeah mate already done that so no idea why they still hold water so might add extra holes to make more drainage and also the other guy on here commented on the white putty in the door seal lip which i might try buying a tube of sommat similar if available and gunge the entire door frame with it or just inject the stuff into the seal all the way round then re-fit and see how i get on for a while ? Also wurth and others do that gummi fit pflege for rubber seal restorer silicone free just l@@k it up on fleabay,thanks for the info pal,regards.
@AlanL200Truckman4 жыл бұрын
Ello Fella... Great video as always. I know it can be hit & miss with aftermarket parts, but generally, they're not too bad & obviously can be a lot cheaper. Stay safe en good health to you en yours. Alan L200
@aaanton114 жыл бұрын
The aftermarket door seals are not as nice as the genuine ones, but they are watertight, they don't cover the trim side so not as pretty, but £115 cheaper, hope you are keeping well Thanks for the great comments👍🏻👍🏻🛠
@pilgrim3344Ай бұрын
Great video, thanks, my driver side footwell is absolutely sodden, how do you go about finding out where a leak may be coming from? Can rubber mats make the problem worse? I removed the rubber mat I had down, dried the carpet, it stayed dry for weeks untill i put the rubber mat back then a week later it was sodden again! in all honesty I assume it was just coincindence, my initial thought was air con evaperation pipe blockeage but i ran the aircon constantly once dry and it didnt get wet
@aaanton11Ай бұрын
This is the usual issue the water leaks in from the rear lights and makes its way to the front kzbin.info/www/bejne/gZanoomfhKaLarM Thanks for the great comments👍🏻👍🏻🛠
@anglosaxonbreed2 жыл бұрын
The wife says it straight away. The guy battle until he gets it right. That the difference the right man for the job.. I can't hear his wife saying well done.
@aaanton112 жыл бұрын
😂 Thanks for the great comments👍🏻👍🏻🛠
@willbedone175712 күн бұрын
What if I don’t have the seal yet but I only need to fill in the top middle of the drivers side…can I fill it in with something while I get the new seal???
@aaanton1112 күн бұрын
take off the old seal and rotate it, then refit with the good bit at the top, Thanks for the great information👍🏻👍🏻🛠
@telosfd2 жыл бұрын
Thanks nice video! Unfortunately I could not find the same sealing rubber with seam, that comes with it. Now there is a gap between the plastics and the sealing rubber. Is there any idea what I can do?
@aaanton112 жыл бұрын
There is a link in the description for an aftermarket rubber, Thanks for the great comments👍🏻👍🏻🛠
@MickyInsegnami2 жыл бұрын
Good content mate
@aaanton112 жыл бұрын
Much appreciated, Thanks for the great comments👍🏻👍🏻🛠
@Kuasarakyat22 жыл бұрын
neatly done. thanks
@aaanton112 жыл бұрын
No problem 👍 Thanks for the great comments👍🏻👍🏻🛠
@MsAngel4346 ай бұрын
Thank you❤
@aaanton116 ай бұрын
You're welcome 😊 Thanks for the great comments👍🏻👍🏻🛠
@millenwagon11 ай бұрын
Thanks for this video, it’s a much easier job than I though. Is it the same for all cars?
@aaanton1110 ай бұрын
Yes, absolutely Thanks for the great comments👍🏻👍🏻🛠
@rajjatkumar270311 ай бұрын
Thank you for this!! Do you have a link or a video on a seal for the back seat windows? My seals has a chunk missing and when it goes for a car wash the water splashes in and can see daylight out of the window seal.
@aaanton1111 ай бұрын
No, sorry Thanks for the great comments👍🏻👍🏻🛠
@martina19703 жыл бұрын
Thank you for this really brilliant informative video, can I ask you we have the 3008 and needs both driver and passenger doors seals replaced where can we purchase these seals? And do you think 4 metres per door be sufficient? Thank you again for the amazing tutorial.
@aaanton113 жыл бұрын
try these tweaks shown in this video before replacing the seals kzbin.info/www/bejne/on2vnHagp62hlac Thanks for the great comments👍🏻👍🏻🛠
@groutness90523 жыл бұрын
How u know as i have 3008 and im getting wind noise at 30 plus sounds like the left side but not sure
@underdogunchained3 жыл бұрын
You legend. Thanks for this video. I wonder how long the boot seal is? I got to replace the onside front and boot seals.
@aaanton113 жыл бұрын
Glad it helped, Thanks for the great comments👍🏻👍🏻🛠
@stevenpeers40299 ай бұрын
How many meters of the door seal will I need for the driver's door of a 3 door Mk 1 Aygo please? Just asking in case someone has already measured it accurately, to save me the pain of trying to do so on my drive in the rain. Many thanks for any help.
@aaanton119 ай бұрын
The seal comes in metre lengths, so 4m will cover it, Thanks for the great comments👍🏻👍🏻🛠
@daveeh62786 ай бұрын
there's a white putty like material behind the original seal on my car. did you fully clean off the metal lip or leave the old putty/seal on? many thanks
@aaanton116 ай бұрын
Leave it on don't clean it off, Thanks for the great comments👍🏻👍🏻🛠
@nothingmuch.30143 жыл бұрын
I fitted a 26mm × 17mm (same seller as descrp) door seal to the driver's door of my 3 door C1, then dried the carpet with a heater. A few weeks later, the driver's front & rear carpet is wet again. I can see where the water is going over the top of the seal, like it was doing with the old seal. Poured water down past the window to check the vapour barrier. No leaks there. I'm tempted to buy one of those D or L shaped, 3M taped seals off eBay, & add an additional seal. They're dirt cheap
@aaanton113 жыл бұрын
Door Seal Water Leak, How To Repair Peugeot 107 Toyota AYGO Citroen C1 CityBug tweak the door like in this video first, Thanks for the great comments👍🏻👍🏻🛠
@yasmaniflores518811 ай бұрын
I tried to change mine with the factory piece but now I can’t close the door properly.. any suggestions?
@aaanton1111 ай бұрын
You might have to pull the door a bit harder to close for a bit until the seals bed in, Thanks for the great comments👍🏻👍🏻🛠
@callummr19969 ай бұрын
What size will i need for the rear doors pls
@aaanton119 ай бұрын
Just measure the seal with a tape measure adding 30cm, Thanks for the great comments👍🏻👍🏻🛠
@juliespragg39993 жыл бұрын
I've brought the seal from your link but bit afraid to do it after read it don't sit as flushed like old one , anyone got any pictures to show as really need to do this ...thanks
@aaanton113 жыл бұрын
Its nice and easy Julie just remove the old one, then fit the new one in its place starting at the bottom & finishing at the bottom, cutting in situ to size, the only difference is the seal buts up to the Interior trim rather than going over it, Thanks for the great comments👍🏻👍🏻🛠
@MrGarymccurryАй бұрын
hi lads their selling the crown jewels again and there will be more, lots more. Where,s the new stadium?
@aaanton11Ай бұрын
?? Thanks for the great comments👍🏻👍🏻🛠
@debbiejarratt5603 жыл бұрын
Hi, Just watched the video of you changing the seal on the Peugeot 107 front door, is the seal the same measurement for the back passenger door as I need to replace this - also do you have the link please for the aftermarket for me to purchase a seal. thanks
@aaanton113 жыл бұрын
Link to previous video on door adjustment to tighten seal kzbin.info/www/bejne/on2vnHagp62hlac Link to After market seal, £4 per meter amzn.to/2wsCZQx ,Note the seal would not go over the carpet edge like the original, but it fits flush to it. Link to silicone spray £8 amzn.to/2wwqAv4 The best thing to do is measure the old seal and add 30cm for good luck, when it arrives you can trim to fit, Thanks for the great comments👍🏻👍🏻🛠
@oxcki2 жыл бұрын
I've just come across this mate it might sound like a daft question but I can't find it anywhere online where to find a rear window seal for my pegeout 308 and mines is deteriorated and cracked / come away from the window. Just wondering if you'd be able to help or give advise
@aaanton112 жыл бұрын
have a look on amazon, Thanks for the great information👍🏻👍🏻🛠
@orfeous2 жыл бұрын
Im having issues with my seal on left rear. Volvo S40 2006. My issue is that the seal is loose. From like half top to middle right. When i push it in it just pushes out like if the seal is too short. Dont know how to fix. The seal does not have a grabby feeling when pushing it in. I have not manipulated the seal in any ways. I mean like banging on it or such. A new one as you say costs about 150 euro.. Any ideas how to repair? Maybe rotate the seal so the "bad" part goes to the bottom or at the left side. Dont understand why it seemt that the seal are short? Do i have to apply some kind of chemicals to the lip on the car so the seal grabs better? glue it down with silicone? Dont know if there are something there OEM.. some kind of something. Maybe put on tape to make it a tighter fit? Please help.
@aaanton112 жыл бұрын
The seal will grab itself, it has a metal structure beneath the rubber, if its too short, a new one will be needed, there are loads of shapes and sizes on amazon you should be able to match one up, something like amzn.to/2wsCZQx Thanks for the great comments👍🏻👍🏻🛠
@orfeous2 жыл бұрын
@@aaanton11 I might have fixed it allready.. i grabbed it and pulled :D matches much better now.. not short now..
@reecevince21663 жыл бұрын
Hey I have a 2006 Peugeot 107 as you know by now 😂😂 and I wanna replace the front bumper with one from 2009 to 2011 only problem I don’t know if it fits I think it well but I don’t wanna risk 130 quid on something that won’t fit any chance that you know if it will from what I can tell all of the mounting holes lineup and looks right
@aaanton113 жыл бұрын
Sorry Reece not one have tried, I think others have done it, definitely worth asking in the city bug forum on Facebook Thanks for the great comments👍🏻👍🏻🛠
@BudsRPGreview Жыл бұрын
How many metres would I need to a 2009 Aygo 1L four door?
@aaanton11 Жыл бұрын
I am sure I mention it in the video, Thanks for the great comments👍🏻👍🏻🛠
@hayleyblackwell29013 жыл бұрын
Hiya have you used the aftermarket seals on your link are they are good as the genuine? Thanks in advance
@aaanton113 жыл бұрын
Many have used them, with great results, I have managed to repair with adjustments and silicone spray on the seals, Thanks for the great comments👍🏻👍🏻🛠
@joeyward98813 жыл бұрын
Hi mate, love your content i have a question if you could help me i have a 5 door Toyota aygo the rear passenger side floor is soaking wet do you think the passenger side door seal needs replacing or would you say i would need to get the rear side passenger door seal cheers.
@aaanton113 жыл бұрын
usually the water always comes from the rear, ie lights, or vents, then it runs forward, Thanks for the great comments👍🏻👍🏻🛠
@joeyward98813 жыл бұрын
@@aaanton11 would you buy door seal on the passenger side rear and then if that has not fixed it then go from there? Thanks for replying.
@joeyward98813 жыл бұрын
The boot is bone dry so it's not coming from there.
@jbebb6568 Жыл бұрын
I have Leak on both rear door windows on a 5 door Aygo and it's coming in through the window seal of the opening windows. The water gathers at the bottom of the seal and runs down the door and into the foot well. I'm looking out for some new seals. Likely to be rather expensive from the dealer.
@davidfoster90134 жыл бұрын
Whats the Red light that comes on the Rev counter when you open the Door ???
@aaanton114 жыл бұрын
I can't see one that comes on with the door, there is definitely no light on the rev counter, only the ones in the speedo unit, Thanks David for the great comments👍🏻👍🏻🛠
@davidfoster90134 жыл бұрын
@@aaanton11 must be a reflection Great videos have watched most of your videos on this car want something run easy to maintain and you made me decide to get one would like to see if its easy to fit a Rev Counter lot of these cars that have look at do not have thank.s again Dave Carlisle Cumbria
@aaanton114 жыл бұрын
Yes rev counters are a doddle to fit, they are just plug and play, the Couling needs a trim, Thanks for the great comments👍🏻👍🏻🛠
@davidfoster90134 жыл бұрын
@@aaanton11 you are Welcome keep the videos up
@zaink70374 жыл бұрын
Thinking of getting a 107 again due to my car not being ulez compliant when they bring it near my area next year. Is yours the allure spec as I'd aim to get this trim model from 2012 when they made the last face-lift.
@1972dazbo4 жыл бұрын
One of mine is a 107 allure on a 2013 plate.....has alloys,tinted rear quarter glass & tailgate,leather steering wheel & gear knob,bluetooth radio etc that is not on one of my other 2013 plate active models.Also between 2012 - 2014 years some are cable throttle and others fly by wire electronic which i never understood why they bothered as the old cable accelerator pedal works just fine without any electronics ?
@zaink70374 жыл бұрын
@@1972dazbo that's what makes me want the allure spec. Just about or is fully loaded and has the nice wheels and rear tints. Didn't know about it having a leather steering wheel and gear knob. I had a 2007 one as my first car before. Was just one spec up the basic one having electric windows and central locking. It didn't have AC which luckily the allure one from the newer models come with standard. Also looks like the newer model comes with front door speakers
@aaanton114 жыл бұрын
The one in the video was fully loaded, had all the spec, the tinted rear glass looks fantastic, fly by wire just optimises emissions I really don't think there is much in it but maybe they can cheat the system by using it ie vw esc, Thanks for the great comments👍🏻👍🏻🛠
@1972dazbo4 жыл бұрын
@@zaink7037 Yeah the allure has leather stitched wheel & matching gear knob,also the 2013 active model i have has front door speakers & air-con as standard.
@bjoernout2.0424 жыл бұрын
Hi, Tanks for these nice Video! I have a 2008 Peugeot 107 5 Door. I still have lil bit Water behind Co-Pilot Seat in the Top right Corner and dont know where this comes from. I made already every Leak tips from whole KZbin and fixed already all... only these place behind Co-Pilot Seat no one can find where it comes from...maybe you or anyone else have a hint? My Question about your Video is: These Door Seal fit for all 4 Doors? Or only for these Door you show in your Vid? Sorry for my bad english.. hope you still understand me ^_^
@aaanton114 жыл бұрын
The seal will fit all doors, if the length is correct, Thanks for the great comments👍🏻👍🏻🛠
@aaanton114 жыл бұрын
also have you sealed the rear lights?
@bjoernout2.0424 жыл бұрын
@@aaanton11 Sorry for my late answer. Lil bit busy since Corona. Yep i seal`d the rear lights already. thats why i dont know really where the Water comes from .
@juliedavie8353 жыл бұрын
Hi can you help I have a Citroen c2 after I have released the handbrake and pull away I get a beep , it has become really frustrating as all obvious checks had been done on it plz help. Thanks julie
@aaanton113 жыл бұрын
possible the hand brake switch is not clearing, and not going all the way down, Thanks for the great comments👍🏻👍🏻🛠
@juliedavie8353 жыл бұрын
@@aaanton11 ok thank you is there any way I would be able to rectify this ??
@avocado714 жыл бұрын
The aftermarket one you linked to wouldn't cover the cut edge of the carpet.
@aaanton114 жыл бұрын
No Andrew, it would fit flush to the carpet edge, granted it not as neat as the original but its another option, I have not found anything aftermarket that is better, If anyone has another option I would love to know as there is room for improvement Thanks for the great comments👍🏻👍🏻🛠
@avocado714 жыл бұрын
@@aaanton11 I'll have a look a other options and let you know!
@underdogunchained3 жыл бұрын
@@avocado71 Have you found anything better since your comment was posted?
@avocado713 жыл бұрын
@@underdogunchained the best solution seems to be to fit an additional door seal.
@zxckmatt2 жыл бұрын
I am wondering why the hell I can order this seal (which is made in Poland) at amazon for 3.89pounds for meter and... at the same time living in Poland I can buy the same seal with 35pounds per one single set for one door at domestic market. WHAT?
@aaanton112 жыл бұрын
Thats amazon for you 😂 Thanks for the great information👍🏻👍🏻🛠
@MrGarymccurryАй бұрын
Archie Gray(alan smith) no KALVIN
@aaanton11Ай бұрын
????? Thanks for the great comments👍🏻👍🏻🛠
@ramparmar608118 күн бұрын
Very bad quality this is too big size and method is totally wrong. Just see marking point from back side put normack joint on top and yellow mark on corner