Phantom 3 Pro Gimble Board Flash No Video Feed Fix

[@3da-io]

You just save my day... and my P3PRO ! It did the trick, I owe you one.

[@themiclic722]

The following is a forum I found with the zip file and pdf mentioned. phantompilots.com/threads/no-image-transmission-signal-p3p.116019/page-3

[@adventurousdavee]

thanks for the video ( 1 year later ) i sucessfully flashed my board following your instructions . Cheers 👌👌

[@minus1849]

In my case when flashing it gets stuck on the target. Please help me.

[@riverbankfisher]

I hope I don't have to embark on open gimbal surgery, but if I do this guide will be very helpful. Thank you sir. I just added this video clip to my archive of conventional wisdom.

[@jimmymauric2004]

Love the video and this is the problem with my gimble board. So I hope I can do it. You mentioned the zip files I will need that you was going to post. Where can i find the files and directions for that? Thanks, Jimmy

[@AlexAmys-xb7ez]

Thank you for this excellent information. I am struggling with the two small pads boot 0 and boot 1 i initially had them soldered and noticed some extra tin attaching from the wire to the component below. When i went to clean it up the wire came up and now i cannot for the life of me get any solder to those pads. I am curious if the pads came off while attempting to clean. Do you have any recommendations as to how to remedy this problem?

[@PamHorton-o4g]

ph3pns does not contain files. Could you reload them?

[@Wallabydam]

I believe I have this problem with mine I let it sit for over a year and when I went to go use it there was no video feed where would I find the software to reflash mine? I know this is a Old Post but I'm still trying to still fly my Phantom 3 professional

[@uavscientific]

Hello, The link in the description for the firmware files is still good.

[@Wallabydam]

@@uavscientific thank you

[@Ewertonnesmotovlog]

Can I get rid of the lack of image error on my DJI Go with this procedure? My PH 3 records but doesn't show live video on DJI GO

[@lucaspajarocauzzi]

Mi cámara no da señal de video, esta sería la manera de Repara ese error? Gracias

[@Ewertonnesmotovlog]

??

[@edmilsonandradematos3944]

Thanks for sharing your knowledge!

[@ahmmmedhijejoo7620]

Hello, I would like to ask you about the possibility of connecting an ordinary av camera to the phantom 3 pro video transmitter

[@uavscientific]

Hello, I am sorry, but the camera video feed is digitized right after the sensor. It would be a challenge to find the av feed before it goes into the chip.

[@BurnedUP78]

does this work on a phantom 3 advanced?

[@dronesetc9769]

The zip file shows empty as of 9/10/2022 for me . I still need these files. I think I downloaded them last year . will comment back if I find them

[@uavscientific]

Hello, Sorry for the slow reply. The link is good again. Click on the "Download All" and it will make the .zip file for you.

[@dronesetc9769]

This linked file wouldn't open, but found one on Github, search there today is 1/6/2024

[@dronesetc9769]

@@uavscientific Here I am a year later, I must have ten or twenty boards here to try flashing. the PDF shows wires to two devices, but you are using one flashing device. I bought a few types will see and report how many I fix for "no image"

[@Dr_dyslexic]

Can you tell me where to get this PDF?

[@uavscientific]

Links to the files keep dropping and popping up. As of now the following works:drive.google.com/drive/folders/0ByK3FyyZ9MnTNGQ0Y29ObU43STA?resourcekey=0-Z9UUddA8tKzkOFaZAMevWQ The PDF is in the zipped filed. You want to download the ph3pns.zip file.

[@Sam1970Sam]

Hi, thanks for the video , super like you ! I have DJI - Phantom 2 Vision the same problem , images are not transmitted to the phone , on DJI - Phantom 2 , too , as well as on video , do I need to do firmware ? That 's the reason , right ?

[@uavscientific]

Hello, Sorry for my slow reply. The PH2 has the same issue with the WiFi module that your cell phone binds to. I hope to make a video soon to flash the module.

[@WethenorthBacani]

Hi, the zip file is empty. Can you create another zip and share?

[@uavscientific]

Thanks for letting me know. Give me a couple of days, I will get the files put in another location and put up a new link.

[@WethenorthBacani]

@@uavscientific appreciate it much

[@JefSilv]

TKS, i would like take this file in PDF. How I can do it.. please

[@naailuschanel2286]

hello my friend from indonesia i tried to follow the method you taught in the video, but when i try to connect the ttl to computer, my dji device doesn't read. please help my friend, thank you.

[@cTeKJloBaTa]

hello, unfortunately I can’t use the link to download the program with repair software, please tell me how can I do this?

[@uavscientific]

Hello, Sorry for the slow reply. The link is good again. Click on the "Download All" and it will make the .zip file for you.

[@gab_nick4262]

When can we get the file

[@csonsdetailing]

Do you still have the board you flashed if so I will buy it from you

[@pavel1809]

i have a dji phantom 3 standard the cam wont move and most of the part have been replace and still doing the same any solution?

[@uavscientific]

Sorry, but this fix is only for the Phantom 3 Professional. It won't work on the Advanced or Standard models. It fixes the no video issue, it won't fix gimble movement problems. My guess is that your ribbon cable is torn.

[@pavel1809]

@@uavscientific ok thank you

[@danangdanang9288]

Hello thank you for the good post👍👍 could you please help me to get the files for my phantom 3 standard

[@inoffice]

HI and good day, thanks for your video, but zip file have folder empty. THANKS

[@Merckxbh]

cara to com esse problema no p3adv ='( ajuda aiii

[@uavscientific]

Sorry, but this fix is only for the Phantom 3 Professional. It won't work on the Advanced or Standard models.

[@bamboleorichie5264]

Hi, I saw yr video and u mentioned flashing P2V+ gimble board..can you share zip file and how to flash it. Thks

[@uavscientific]

Hello, Sorry for my slow reply. The PH2 has the same issue with the WiFi module that your cell phone binds to. I hope to make a video soon to flash the module.

[@R_Squared933]

Thanks for the video, however, the file linked is an empty folder.

[@uavscientific]

Hello, Sorry for the slow reply. The link is good again. Click on the "Download All" and it will make the .zip file for you.

[@uavscientific]

Hello, I am sorry, but I could never find files for the P3S model.

[@jimmymauric2004]

Love the video and this is the problem with my gimble board. So I hope I can do it. You mentioned the zip files I will need that you was going to post. Where can i find the files and directions for that? Thanks Jimmy

[@gab_nick4262]

Or where

[@kenanthonyadiaz2660]

My p3ad block screen but still record og my sd card

[@aldsn.project9741]

how fix this problem sir?