PHANTOM 85 LAST RIDE

UNTIL FURTHER NOTICE, THE PHANTOM 85 WILL BE SHUT DOWN

[@loganwilson5457]

Very surprised you got even the first ride out the price of junk Phantom 85

[@mybikes1970]

😂 Its fixed and still running lol but it was "a piece of junk" for a while👍

[@leonardarola]

Firstly, love your trousers choices (all of them), secondary, love Puerto Rico, thirdly, thanks for the ride.

[@mybikes1970]

Haha! Thanks for noticing my "riding pants"! Thanks again for watching

[@MixMusicArt]

the analog speedometer of your moped oscillates a lot because the whip cable is crooked. if you put it more straight the needle of your speedometer will not oscillate

[@mybikes1970]

Gracias por ese consejo👍 Ya lo saqué de la bici porque el engranaje que mueve el cable estába dañado

[@MixMusicArt]

De nada amigo

[@Littleevil9975]

Nice ride bro good luck getting it fixed

[@mybikes1970]

Thanks bro! I can always put a YD100 upgrade cylinder kit on it 😡

[@Littleevil9975]

I was wondering can you just get a wrist pin and bearing and stuff from a yd and put it in it to fix the problem

[@mybikes1970]

@@Littleevil9975 the stock YD has 10mm pin and the Phantom has a 12mm. For now I just bought a bushing for a vespa moped that will fit. I'll let you know how it turns out.

[@Littleevil9975]

O ok I see didn’t know that

[@mybikes1970]

@@Littleevil9975 when I take apart the Phantom 85, I'll make a video comparing the differences between the it and the YD100

[@ELISRACINGTEAM]

Bueno el video . Sube la cámara más esta muy para abajo y dale suave . Recuerda q entre mas dure el video mejor . Suaveeeeeeeee y sube la cámara . Saludos desde ny .

[@mybikes1970]

La cámara normalmente está en mejor posición pero se movió cuando estaba pedaleando. No me di cuenta hasta que vi el video. Saludos desde PR!

[@vincent10717]

I hope they fix the issues with the phantom... they have so much power!

[@mybikes1970]

That would be great but I doubt it. I don't think I will buy another especially not from bicycle-engines.com

[@user99524]

@@mybikes1970 they fixed it

[@mybikes1970]

@@user99524 kzbin.info/www/bejne/eanTiYF9Zs56f80 I know 😉🙏🏾

[@Krisanic]

How do you run the headlight

[@mybikes1970]

Four 3.7 lithium batteries

[@elpepewow4825]

Este motor esta a pruebas en México,,y le llaman el zt 85 pero es el phantom , pero detectaron defectos en el,al parecer son los bujes de biela,,,,pero a ti que referencia nos das de ese motor ,,??es buena la máquina?? Dinos de la potencia y torque y en subidas que tal?? Y cuantos dientes tienen sus sprokes?? Gracias ,, y saludos desde México

[@mybikes1970]

No compre ese motor. La potencia y torque es muy buena. Usé un sprocket de 40d y puedo subir cualquier cuesta y es muy rápido (más de 65 km h) pero la calidad es horrible. El buje de la biela y los anillos del pistón tienen un diseño defectuoso. Si el costo es barato, puede comprarlo y cambiar los componentes defectuosos, pero ya no vale la pena.

[@elpepewow4825]

@@mybikes1970 Muchas gracias por la información,, saludos

[@mybikes1970]

@@elpepewow4825 de nada bro👍

[@elpepewow4825]

@@mybikes1970 Feliz año broo

[@mybikes1970]

@@elpepewow4825 gracias bro! Feliz año para ti también

[@Rccrawlerhobbyplus]

ESTA Buena para pasear

[@mybikes1970]

A veces sí 😁

[@ballista2271]

how do you know if it has problems when it runs fine?

[@mybikes1970]

Remove the cylinder and inspect the piston and bushing for wear. It will run fine and strong right until the last moment before disaster strikes.

[@Adalbertomatos_]

De dónde eres porque según las imágenes del vídeo me atrevo apostar que es mi isla del encanto Puerto Rico yo soy de Ponce

[@mybikes1970]

Soy de Aguadilla. Saludos!

[@ne0tas]

they switched to a roller bearing

[@mybikes1970]

That's good news. It should be much better now but I don't want another one 😉

[@BuildBreakFix]

It sounds like it's made in china rofl!

[@jonnyc2.047]

YYYY SPAND 300 ON THIS WHIRTH REECALLS WIN U CAN BUY A KTM 50CC 3GERS 2STROKE FAST AS HEALL 60 EZ MPH

[@mybikes1970]

The KTM is fast but has a weak transmission compared to the manual clutch on that phantom motor.I can go up hills easier and for less than $30 the problems are already fixed. Thanks for watching👍

[@joneserupinsmoke9161]

What oil mix ratio did you use for break in ?

[@mybikes1970]

At that time, I used 24:1. When i rebuilt it, I used 16:1. I think it's better for the wrist pin bushing, so it doesn't get worn out too soon.

[@joneserupinsmoke9161]

@@mybikes1970 Bro and I just looked in muffler all the installation is blowing out of it and again we're talking only like six rides that were only for 15-20 minutes at the most girl these kids are disappointing me left and right

[@mybikes1970]

@@joneserupinsmoke9161 I wish I could have warned you before you bought it bro😔

[@joneserupinsmoke9161]

@@mybikes1970 Bro I just watched a clip .pop in does my two stroke run hotter with 50 to 1 or 25 to 1

[@mybikes1970]

@@joneserupinsmoke9161 if it's not lubricated enough, it will cause more friction and run hotter. But that's just my opinion.

[@ej8_haz33]

esos motores salieron malos pero so lo le tenies que cambiar lo q aguanta el piston

[@mybikes1970]

Ya cambié el bushing

[@zychozen]

Was that full throttle And how much do you weigh

[@mybikes1970]

No. Maybe 3/4 throttle,40T sprocket and I think I only hit 30mph. I weigh 173lbs

[@joneserupinsmoke9161]

@@mybikes1970 Damn bro that's it ? I got a anbull "100" cc and with a 44 tooth I hit 43 top rip and its all stock all I did to it was cut a hole in center of air filter

[@mybikes1970]

@@joneserupinsmoke9161 Lol that's as fast as I was willing to go Bro, too much vibration over 37mph and I couldn't feel my feet on the pedals. I thought about an Anbull100 but for now I am done buying 2strokes.

[@LaCourierInCrysis]

I'm trying to live in Puerto Rico help me I build

[@mybikes1970]

Bueno, para el futuro, si necesito ayuda para construir, se lo haré saber

[@awdrifter3394]

Is the Phantom 85 any better than the YD100?

[@mybikes1970]

It has more power than a YD100. It's a YD100 on steroids. But for now, they are unavailable due to poor quality piston pin bushings

[@awdrifter3394]

@@mybikes1970 I see. Thanks for answering.

[@joneserupinsmoke9161]

Bro hell yea it kills yd 100

[@joneserupinsmoke9161]

But it all depends on what ur looking for the 100 with rite set up hits really good top speed for what I heard on utube but as a plug and play with 44 tooth sprocket or 36 rite out the box definitely sweet.i like engine where it has good power and dnt have to go crazy on getting it up there until u want to ya kn

[@scotthansford3657]

when did these issues occur? how did you diagnose? and are you gonna make a video fixing them?

[@mybikes1970]

I dont know when these issues occurred or if they are true but I keep getting comments that the motors might fail. There is a video on youtube of a guy diagnosing the bearing and maybe I will make a install video

[@scotthansford3657]

@@mybikes1970 please do!

[@jaayse]

You need brass not that fake aluminum. The bearings for this piston and rod are 12x14x15

[@mybikes1970]

@@jaayse I already ordered a bushing as soon as I found out about the issue. It should arrive this week. Thanks👍

[@jerryb1234]

Parts for these aren't available yet, ya might want to fix it before it comes apart on ya.