Philips Saeco Syntia coffee machine. Grinder not working. Pre ground coffee mode works good.
Пікірлер: 29
@dioni82 Жыл бұрын
My machine stopped grinding ~8 years ago. I blindly replaced the motor and grinder sensor at the time but it did not help. I gave up and continued using it with pre-ground coffee only. After watching your video I managed to identify and replace a faulty resistor (R127) which was OL. I didn't have any spare components handy so I scavanged the resistor from an old broken pcb board which I had kept just in case. Cauple hours of work total and no extra cost and the grinder is working again! I can't thank you enough! You are a legend!
@beanmeup99023 жыл бұрын
Brilliant . . . thank you Sir! Fantastic primer on a basic diagnostic and repair method that can be extrapolated to diagnose other components on the Syntia/Saeco boards. Well made video!
@michaelgreig99703 жыл бұрын
Thanks, this was super helpful to me in troubleshooting my machine!
@moisesbursztein28305 жыл бұрын
Thank you for sharing. My problem was that the grinder was working and the grounded bins start first going to the waste basket and then the grinder will spin but no coffee was delivered. Thanks to your video I was able to take the brewer apart, unclog the grinder and now it seems to work fine.
@rookiediagnosticsandrepair59565 жыл бұрын
Glad that worked for you!
@alberona1003 жыл бұрын
@@rookiediagnosticsandrepair5956 how did you take the brewer apart and unclog the grinder? i would appreciate your answer. than you, tony
@MrSznajder952 жыл бұрын
"E S Presso" to repair the coffee machine - brilliant!
@dannydries50943 жыл бұрын
thanks!!! i had a bad r63! very cloos, very helpful!
@en2oh2 жыл бұрын
can this resister cause "intermittent" no beans problem? My grinder always "works" it just doesn't always sense the beans
@dioni82 Жыл бұрын
I had to replace R127 and R111 for the grinder to start working again.
@en2oh2 жыл бұрын
just checked my board.... missing the cap above the Triac and the resistor you have identified as 330ohm is 181 on my board.
@HappyHighwayman Жыл бұрын
Any idea how to clean the grinder that works but is oily from oily beans and won't suck in the beans?
@truenorthmuskoka90773 жыл бұрын
I have the Saeco Syntia and it seems to go through periods where it dumps the ground beans for the first espresso without actually brewing it. It seems to do this regardless of the brand of beans. Any idea why it does this.
@coucouj27818 ай бұрын
I have a problem with my display. All the color works green yellow and red, but the pictures are barely noticeable. I changed the LCD again, I thought I had a bad one. Any idea on the problem? Very fainted pictures (icones)
@fekrabrico82034 жыл бұрын
I thank you very much for what you have given us, in particular, clarifying a corridor, starting from the electricity inlet circuit to the electrical outlet of the coffee grinder, and found us the reason for the damage. Can you help me please ? I have the same model as Philips Cynthia and I think you will know where the problem lies first. The card is clean and its problem is that the electricity is connected but nothing works like this hand does not ignite and there is nothing that works as if it is disconnected from electricity. When I arrived at a meter using the meter, I couldn't figure out which circuit was responsible for opening the switch so that all the power outlets for the engine and screen would work for others. Can you show me the places to look? I doubt Optecopler. and thank you
@rookiediagnosticsandrepair59564 жыл бұрын
I'd start with fuses. Sorry it was long ago.
@fekrabrico82034 жыл бұрын
@@rookiediagnosticsandrepair5956 Please, you are the only one who can help me. You can tell me where the electronic parts are, and the rest will be very hard for myself and my Lord will reward you on the day of reckoning Please my dear machine, my wife and I beg you
@evarosbergcody5725 жыл бұрын
Hi, it seems like I have a different problem with my own broken machine, no water ever reaches the brewing unit. Instead all comes out under the machine. I could have a broken overpressure valve? The instructions are great, but I cannot get the round front knob, nor the steamer off to even start disassemble the machine. Any chance you could explain this? Eva
@rookiediagnosticsandrepair59565 жыл бұрын
It was some time ago if I remember right you need just to pull the shiny part of the round knob and there will be one screw under it. Steamer can be removed after external panels removal but you need to undo the steamer plastic cover that is held by two clips two very fragile clips to the metal on the machine. You can also try to search youtube I believe there was another video with disassembly of this machine )
@evarosbergcody5725 жыл бұрын
@@rookiediagnosticsandrepair5956 Thank you so much. I will have a go at it tomorrow!!
@littlebitfromeverything4 жыл бұрын
I did open service mode, on grinder menu, i am pushing and grinder start for 2 second and setup and screen turn to red. What is problem?
@rookiediagnosticsandrepair59564 жыл бұрын
Sorry I am not a professional service for these things.
@dasboot18204 жыл бұрын
My machine is a bit older, no fancy multicoloured display. IN the morning the machine will not prime. It tried to prime goes through the motions but no water comes out of the coffee spout. It errors with water pump issue. I crank the knob to the right, water comes out of the hot water spout and everything is Okay. after that.. Not sure what is causing it but it is a pain to deal with in the mounting. After that the machine works fine all day long. Any ideas?
@rookiediagnosticsandrepair59564 жыл бұрын
Sorry i am not that goid with these machines. I would check if voltage appears on waterpump during fault and normal work. If voltage is present both times than pump is faulty
@mikeballmball3 жыл бұрын
Hey man, just in case you are still dealing with this... Take the brew group out, remove the filter assembly and unscrew the shower screen. It can get quite clogged. If the micro coffee grounds are dry, they won't let the priming function work, however once they get a bit wet they loosen up enough for the coffee to come out. Once it dries up again the same issue presents itself. Because the holes are so small, I had to give the screen an ultrasonic bath using my wife's jewlery cleaner to unclog everything. Hope this helps.
@dasboot18203 жыл бұрын
@@mikeballmball I got it sorted but I will try to as a maintenance issue. Thanks for that.