DIY Kydex Mag Carrier Part 3

[@dbirk3285]

My favorite part of this video is Clutch playing in the background during the press. You just gained another sub

[@ewilsonheritage]

great video! I started making mag holders recently. It is definitely an addicting hobby. I enjoyed the video...

[@SH4DOWTROOP3R]

Hey brother, love the vids! I've used a hair straightener on the body curve sides. Works pretty well and focus' more heat where you want it and not where you dont. Keep it up!

[@thomasgreen8532]

using a center punch after you marked the location of your holes will help you from missing your Mark as you drill. It does not need to be much just enough so that the drill bit can locate the place you want to mark also using a smaller drill first helps to make sure you don't bugger up the hole as you are drilling.

[@thajuice0]

What temp does the kydex need to reach before it is pliable?? Can body heat and wearing them when its extremely hot deform them?? Great vids bro!

[@daltonleitz9999]

Stoked when I heard Clutch and the Misfits. Awesome video aswell!

[@elkbow]

nice, but you forgot to put on the belt loops, but noticed you had them when drawing the magazine at the end, thanks for the video's

[@krayzeetat2s]

haven't heard canderia since high school... whoa! lol i been watching all your videos... i just ordered stuff to make my own holster... i appreciate u takin the time to film everything... btw .. i work in south philly ... where u from... thanks again

[@kenpoist7]

Nice work Jon!

[@52hubcap]

Why won't the part 2 video play?

[@johnrice1943]

Banned in America for copyright. Try a VPN.

[@turkeycreekknives133]

Rebar protection tops in home centers carrying rebar required on construction sites these days

[@LiquidZ2k]

What is the best point to use for retention on the mag carriers, guns are easy with the trigger guard... but the mag carriers seem to just need sheer tightness all around.

[@nathanstotts8519]

PhillyEDC do you use a special bit for drilling the holes?

[@turkeycreekknives133]

Drill bit is a bradpoint drill bit don’t lets these supply guys tell you it’s custom made for kydex just charging you more HD or Lowe’s carry

[@PHLster]

@Lordie2099 Thanks for your feedback, man! I'll take a look at your videos and learn from your example.

[@swaffy101]

Great work and thanks for the info!

[@PHLster]

@12345NoNamesLeft Gotcha. They're just referred to in the catalog as a rivet and if someone wanted to order from the same source as me, they'd never find any "eyelets."

[@PHLster]

@SentryGunleather Lol! They're all over my house. I find those sumbitches EVERYWHERE!

[@MajorGRecording]

Have you ever tried using a chamfer tool (for reloading brass) to remove the bits of kydex from your drilled holes? I am wondering if it might be a better tool than a knife.

[@cliffcares6455]

Have you tried to drill out a bad rivet instead of just crushing it?

[@PHLster]

Cliff Cares If the drill bit causes the rivet to spin, the rivet can bore through the plastic. If you drill really slowly, you can maybe avoid this, but it's faster and easier to just crush down the unfinished side and push it out.

[@cliffcares6455]

PhillyEDC Thanks for the fast reply.

[@sethsheppard7008]

How much u sell those for.

[@510DEACON]

Heyn cool videos I see u mention how many holsters it took to pay for the tools but in video 2 u didn't mention how many beers u could buy with one holster had to say it good little hobby and u can make some cash if u want

[@nerd9684]

@Welsh y not unless you reach 320 degrees that's the temperature to make it plyable lol

[@zato6226]

If you haven't figured it out yet, it's catching on the bullet.

[@jbellis11]

+1 for Clutch

[@mikefromwa]

The only problem with these mag holders is they're about 3 times as wide as the magazine, which seems like a lot of wasted space.

[@12345NoNamesLeft]

What you're calling an "open rivet" is an eyelet.

[@CQBSLITHERS]

the kydex itself is expensive

[@5150madawg]

thats a horrible way to remove the eyelet way easier to drill it out !! imo