Piaggio Fly - CVT Removal - variators, belt, rollers, clutch | Mitch's Scooter Stuff

In this video I show you how to remove drive belt, rollers,variators on Piaggio Fly scooter.
TOOLS I USED:
#2 Phillips Screwdriver - amzn.to/2fgdZDL
Flathead screwdriver - amzn.to/2jN7lpE
Nose pliers - amzn.to/2yetDDj
Bar - to lock the wheel
Magnet stick - amzn.to/2CkmFhx
Rubber mallet - amzn.to/2BsqAMz
Variator / clutch bell holder - amzn.to/2YC8L6B
Breaker bar 1/2 drive - amzn.to/2HenuMI
1/2 to 3/8 drive socket adapter - amzn.to/2xGFAUG
19mm socket 3/8 drive - amzn.to/2CiXNqo
Ratchet 1/4 drive - amzn.to/2xcJEu1
3” / 6” extension set 1/4 drive - amzn.to/2wDuzzW
8mm socket 1/4 drive - amzn.to/2xMhsBl
Dr Pulley Sliders - amzn.to/2GFUUCC
Drive belt: amzn.to/2Bsz0n3
More videos on this scooter - bit.ly/2fB7mdS
SHOP MY SCOOTER STUFF: amzn.to/2CbqQku
Want more free Scooter Tip / Tutorial videos - Please support MicBergsma!
Paypal donation: bit.ly/2fghrwN
IMPORTANT
Please only use and share this embed code of the original video.
Third party downloads and distribution is not permitted.
If you are interested in buying footage or for booking information please contact:
[e-mail]
*******************************************************
Website - bit.ly/2gvBRyI
KZbin - 2nd channel - bit.ly/2g4i5d5
Instagram - bit.ly/2fB8gay
Facebook - bit.ly/2gEsYpt
Google Plus - bit.ly/2fPb423
******************************************************

[@jamesconner3437]

Have done two belt and roller changeouts by now. Mitch is very good...i was a complete newbie to cvt transmissions before.

[@berlitzvonternitz]

tatellos ohne nervige musik im hintergrund und man sieht alles perfekt vielen dank

[@700tbm]

Thank you Mitch! Greetings from Finland. Without your videos, I would never have had the nerve to take my scooter apart. I just successfully replaced my rollers/sliders to lighter ones! Even got my scooter back together with zero parts left over 😅 2015 Piaggio fly 125cc.

[@eisenbahn-fuzzi2804]

Sensationell leicht verständliche und detaillierte Beschreibung. Vielen Dank dafür.

[@MitchsScooterStuff]

TOOLS I USED: #2 Phillips Screwdriver - amzn.to/2fgdZDL Flathead screwdriver - amzn.to/2jN7lpE Nose pliers - amzn.to/2yetDDj Bar - to lock the wheel Magnet stick - amzn.to/2CkmFhx Rubber mallet - amzn.to/2BsqAMz Variator / clutch bell holder - amzn.to/2YC8L6B Breaker bar 1/2 drive - amzn.to/2HenuMI 1/2 to 3/8 drive socket adapter - amzn.to/2xGFAUG 19mm socket 3/8 drive - amzn.to/2CiXNqo Ratchet 1/4 drive - amzn.to/2xcJEu1 3” / 6” extension set 1/4 drive - amzn.to/2wDuzzW 8mm socket 1/4 drive - amzn.to/2xMhsBl Dr Pulley Sliders - amzn.to/2GFUUCC Drive belt: amzn.to/2Bsz0n3 More videos on this scooter - bit.ly/2fB7mdS SHOP MY SCOOTER STUFF: amzn.to/2CbqQku

[@TankumK]

Great job Mitch. Thank you!

[@martintylsar7782]

Super, pomohl jste mi, nevěděl jsem kam patří ta podložka pod matkou na variátoru se zářezi.

[@Red-sr7vo]

Your awesome dude me and the lady followed this and now we are a rockin keep doin the do buddy

[@RafikiAWF]

Great and very helpful video. Thanks!

[@timjhonson925]

Mitch, do you have a video on how to remove clutch assembly, I think I have lube leaking out of the oil seal. Thanks for all the videos.

[@myname6169]

I need help with my 2007 piaggio fly - steering is tight making it hard to turn at faster speeds. Your videos have been a great help to me thus far

[@garrysutcliffe6254]

hi Mitch,thanks for the great videos , I'm struggling to split the case any tips, got the far left part out but rest is stuck around oil funnel

[@renditabak6428]

great master you are,thanks for your all videos.saluti from Croatia town of Split

[@marcellusxiii]

Awesome man!

[@DJSherman]

perfect camera work. no annoying music. right to the point. I guess there has to be shitty how-to videos out there to know how good this one is. Thanks!

[@MitchsScooterStuff]

No problem!

[@richardshomemechanics5566]

good video very well explained well done 👍

[@neilmitchell8378]

Excellent

[@SmartDrug]

Thank you for this!!!

[@gm32801]

What a wonderful guy😊🎄✨🤝

[@ninomorris2593]

Bravo

[@7eis]

Thanks for the great visual explanations Jesus ❤️

[@AmericanPunjabi1313]

i learn much more from your video

[@MitchsScooterStuff]

:)

[@rieewoldt]

Hi - awesome video! does he variator need to be off before the clutch assembly can come off, my clutch seems to not budge with the variator on still

[@drummerdem50]

Nice job

[@user-dz6vm3su5g]

Bravo nice job

[@jerrymulholland5752]

thanks for the videos, big help. One tip. work with bike on center stand. remove lower shock bolt and push shock back. lowers engine and makes cover easy to remove and install.

[@MitchsScooterStuff]

😄👍🏼👍🏼

[@albind.386.]

Omg. Thank you. I didnt manage it before. 👍👍

[@user-vw9uy7kq6k]

Excelent video of great help, thanks for share,Like !

[@paulquiroz4070]

Hello Mitch, thank you for every video that you have posted.... now I need help. I have a 2006 Piaggio FLY150, and it does not go over 30 miles/hr. Already replaced the belt and the weights. Any suggestions? Thank you in advance

[@destanstein1875]

Hello Thank you for your Videos I like it. I have a piaggio hexagon 125 4stroke but it Runs only 90 km/h can you Tell me what can i remove or do to make it faster Thank you :)

[@cpasmoimoicpas]

Parfait !! tu es excellent merci beaucoup👍

[@MitchsScooterStuff]

You’re welcome! 😄👍🏼

[@AmericanPunjabi1313]

best technic thank u

[@eeronieminen]

Impact gun is great

[@jaslovecraft]

Gracias...

[@joerigillissen9324]

I feel like my clutch is engaging too early, so i want to change out my clutch springs. Is that hard to do? Thanks in advance

[@facundoclavoalfano4626]

Bravo!!

[@michelepintuspaci5378]

How do you remove the plastic covers that prevent access to air filter and cover (the lower one I mean)?

[@williamsalazar2188]

Sería bueno que explicaras cómo sacar los plásticos. Para no partirlos pues. Gracias

[@shwanabdulqader5096]

Good job.....from iraq

[@Bender_Rodriguez]

Man use for clutch Buzzetti 5428! for safety and good job! cheers!

[@Rebuild-ub5cu]

Hi! , thanks for posting this video- friends Typhoon has snapped belt. :)

[@MitchsScooterStuff]

Anytime! Glad to help out!!

[@Ipuffiiiiii]

Thanks dude

[@MitchsScooterStuff]

Anytime!

[@tomweaver7442]

Hey Mitch, Great videos. It seems that my 2010 Piaggio BV 250 clutch? isn't disengaging. Sometimes I can't push it backwards or forwards. Also, I'm having a difficult time finding someone who is confident to work on it in the Monrovia, CA area. Any suggestions?

[@MitchsScooterStuff]

Hi Tom, thank you! It sounds like your clutch shoes are wore out... remove the clutch housing to check the shoes... you could try modernvespa.com

[@sergiohidalgomartin3050]

Hola,, el caso es que cuando intento aflojar la tuerca de la tapa de afuera me es imposible,, esta durisima,, pero me e dado cuenta que por el lado derecho donde el tubo de escape la tuerca también da vueltas y no se si irá en conjunto o no,,, por sujetar ambos lados o no tiene nada que ver,, no se si me podéis ayudar,,

[@pinpon853]

Hey Mitch! do you know how to desconnect the piaggio fly 150 side stand to motor keep the motor on when you move the stand? Thanks man!

[@vcpunx8]

I want to deristrict my new 50cc Yamaha zuma 2015 anything on modes to this at all need more speed.

[@AmericanPunjabi1313]

good job specialist

[@MitchsScooterStuff]

Thanks!

[@dennisdouglas]

Hi Mitch. Love your videos. I have something bad going on inside the gearcase or maybe the clutch. not sure which but sometimes when i take off it makes a horrible sound like my kickstand is dragging on the ground but its not. Sometimes with the sound it jerks a bit for a few feet. Only occasionally and more so when its hot outside. Other times it runs smooth, quiet and perfectly. Do you have any idea what may be causing this noise?

[@omrizaitman1752]

following 🙂

[@MitchsScooterStuff]

Hey thank you so much! Hmm sounds like your clutch pads are gone… here’s old video kzbin.info/www/bejne/gH-8pIaajNVqq8k I posted long time ago how to inspect the clutch pads… pads should be 2-4mm thick. How many miles on yours?

[@dennisdouglas]

​@@MitchsScooterStuff I have close to 9000 miles on it. All original stuff in it. Where can i order new clutch pads? Like I said 99% of the time it runs like a new bike. Once in awhile i get that noise on takeoff just like my kickstand is dragging on the cement. I check and it is up. Could clutch pads make that terrible metalic sound?

[@StodgyFoot93]

hello..the key that locks the variator which measure are the screws and how long is the key..thanks

[@gupta704]

Can you please give guide why scooter Piaggio Liberty 50 CC, doesn't start electrically; battery is good, fusible is good. manually with crick it does start..

[@erkanmustafa4495]

My roller plate does not come out. How can I get it? The scooter is Piaggio Liberty 125.

[@telosfd]

My Piaggio fly 150 last time creating noise ( like vibrating) in the front of the steering any idea what's going on? Thanks a lot.

[@JDMz]

Could be brake disc or head stud bearings in the steering

[@andonimunarrizgainza6002]

what is the function of the tube that has a ziptie ?

[@jgrinnell7431]

Hi daft question but these 4 stroke piagio have restrictor

[@maxfroeder]

Aí mano vem trabalhar comigo aqui na SOS SCOOTER

[@forevercomputing]

I don't agree on using a screwdriver to hammer with. Steel into alloy means the alloy will mar or become damaged. Either some wood, brass bar, or something else softer would be better.

[@jmconner356]

Forever....maybe put it in your own how-to video. This guy is as good as it gets for us, and most of us know not to beat soft stuff with harder things using much force.

[@alfredlummer9617]

You should include the removal of the panels.....

[@viciousviolet3783]

Question. Mine vibrates on and off when you have the throttle on. What could it be?

[@mukulsingh2540]

where is the outlet of cvt cooling air? it enters via duct but where does it exit?

[@Fredjoe5]

There's an opening to the rear of and below the clutch. Basically, just a square hole, I believe.

[@rosannatodisco5785]

Ciao scusa com devo mettere la pompetta della benzina del liberty 125 perde benzina

[@romaincbdt3146]

Bonjour sur l'embrayage vous avez pas les ailettes c'est le même moteur que le x8 x9 125 150 sa chauffe pas du coup. Moi mon x8 2004 jai lever les ailettes l'écrou 46 ne rentre pas comme il faut est ce que il y a un risque de cassée. Merci

[@kalyangautam7345]

In my scooter there’s too much noise coming from clutch box I already changed belt, clutch shoe, clutch shoe bearing but still noise coming like motor.will you give me solution?

[@nancy_lessard3030]

Mine does the same, it is normal this thing is spinning very very fast

[@kalyangautam7345]

@@nancy_lessard3030 but there was no that problem

[@chuchu2301]

Hi Mitch! I need some advice please?.. I have a 2011 piaggio fly 125 which started having a slight issue.. while almost coming to a complete stop, there is a flapping sound coming from the rear of the engine. The sound is like flicking a piece of paper with your finger. But this sound only happens when you the scooter is coming to a complete stop. The sound is louder when the scooter is cold and when it has warmed up, the sound is not so pronounced.. any ideas?

[@gupta704]

it gives sound cric while pressing electric button to start;

[@user-nq9fl2hg9x]

👍👍👍👍👍👍👍

[@Jimbo505]

Is it essential to moan like you do to remove the vario ring or is it just part of the experience?

[@juliocesarmonzonsangama2889]

Saben la medida de la faja de la piagio?

[@andreasfriso2946]

Mi potresti dire la coppia esatto in nm di seraggio variatore e frizione Grazie dal Italia

[@MarjanrDicoski]

what are the dimensions of the rotor holder.

[@ermelindogomes3494]

👍👍👍👍👍👍👍👍👍👍

[@robertosorrentino133]

Ciao, o visto il video ti vedo molto preparato, , su questo scooter piaggio fly 150, Io ciò 1 problema Nn fa più di 90 km orario, voglio cambiare i rulli, secondo te di quanti gradi devo mettere i rulli, x arrivare a 110 km????.

[@isaacguerra7621]

Que numero de correa utiliza

[@Mk3_mf]

What is the measurement Qaish?

[@jcsworkshop5906]

0:17 I didnt know the video was about how to finger the airbox of your piaggio 🤔

[@lindaterry9422]

Why I feel shaft to short get back on shaft

[@slutica]

Step 1. Show me how to get the bloody fairing off! Fark me!. Ok so manage to get to 3:50 with the farings on, but just cant pull the cover off over the oil inlet (yes the cap is off). Jiggle, Jiggle jiggle last 3 hrs. So frustrating.

[@Fredjoe5]

Looks like your swingarm bushings might need replacing.

[@Mk3_mf]

اشكد قياس القايش

[@tiehut]

what year scooter is this?

[@MitchsScooterStuff]

+tiehut 2009

[@user-mn2in8mf5h]

شنو اسم الدراجة هاي

[@frml6048]

Nadie le dijo para q son los dos agujeros en la tapa de carter !! Jaja

[@brendamake1760]

Locking wheel with bar worked good. They also make this for holding clutch: www.scooterwest.com/items/?_pageCCS=t#page=/item_details/Clutch-Holder-Tool-ET4-LX-150-GT200-GTS250-and-More/1309

[@souloukex6680]

+Brenda Make or 2 screwdrivers it works too

[@pirpir3496]

+souloukex Just put on the rear brake

[@souloukex6680]

+Pir Pir no it doesn t work

[@Bender_Rodriguez]

and buzzetti 5030 for variator......

[@NshsShdh-jx9ob]

❤️👍👍👍🥰🥰

[@user-wb7qn6ew8k]

ماكو واحد يصيح مي ارو

[@AlvaroSanchezChile]

Hi Witch, great video, this is the Piaggio Leader engine? I`m planing get this scooter www.gildemeistermotos.cl/sr-motard-125/ here cames with the Leader model engine manufactured by Piaggio. Thanks in advance for your input