Picasso Interior Fan Only Works on Speed 4 - Resistor Change - Also Shows Glovebox and Motor Removal

In this video we have a Citroen Xsara Picasso in which the interior fan only works on top speed. We fix it by replacing the heater resistor. The step by step also shows removal of the glove-box and fan motor.
#iofix​
This video is brought to you in association with We Buy Cars Bristol (UK). webuycarsbristol.co.uk
WE BUY CARS BRISTOL ALSO BUY BOATS:
webuycarsbristol.co.uk/sell-m...
... AND CAMPERVANS:
webuycarsbristol.co.uk/value-...

[@alexkharitonov3339]

Thanks for the video. Here is a tip to make your life easier next time: Twist resistor clockwise and pull. It'll drop down with the connector. Now, there's no need to vandalize the poor old thing. There are two side tabs on the connector, just press them and pull off your old resistor. It took me less than 10 seconds to get it removed from the shaft. BTW, if the heater motor is squeaking, give it a gentle tap and it'll stop.

[@iofix]

Thanks for the comment.

[@richrichard100]

Great tip thanks, saved me a lot of stress .

[@mixerfistit5522]

Excellent addition to the video Alex. Came out easy Also thank you iofix for this video

[@garvie88]

Thank you for the video, would never have attempted this without your help. Replaced and working great

[@iofix]

Glad it helped - sorry for the late reply.

[@bruceBruceDowellocoUk]

Thanks excellent demonstration. I was dreading doing this I have hands like shovels and a big 6”4” it was good to see the issues you had and steered me away from doing the same. it took me 20 minutes start to finish. spending time on the video saved time plus probably money not breaking things. My wife now thinks I’m a mechanic. Little does she know. Note when moving the wires to twist the fan, the connectors were on holders stuck to the frame, so they just pull off and I didn’t have to take them apart. The resister just twisted and I just pinched the connector straight off. I did have to mutilate it to take off. Thanks again🎉

[@iofix]

Glad the video helped u, and thanks for the extra info.

[@amandajarvis4009]

Thank you for this video, I amazed my husband replacing the blower motor with this, I'm now a super star, mine was slightly different being the air con version, just an extra plug really, We now have air perfect thank you.

[@iofix]

Great, glad the video helped u! :)

[@glynduffield2383]

The hole in the motor where you think there could be a screw is there in the event you break the tab when you twist out the motor. If that happens to you, just put the motor on and secure it using this hole and a self taping screw

[@iofix]

Thanks for that info - sorry for the late reply.

[@michaelloundes4469]

thanks for the vid, my blowers stopped on all settings, changed the resistor and all good now, vid helped a lot

[@iofix]

Great, glad the video helped, thanks for messaging.

[@Ma7hiu5]

I'm so glad I found this video, need to attempt this tomorrow, hoping all goes well..

[@iofix]

Glad it helped you - hope it goes well.

[@markwilliams2830]

Great Video.Very VERY well explained.Your tips about removal are invaluable.Thanks for sharing.

[@iofix]

Great, glad u found it helpful, thanks for the comment.

[@richrichard100]

Great video, saved me a lot of stress also Great comment from Alex.

[@iofix]

Glad it helped - thanks for messaging.

[@davidgriffin7949]

Really helpful video, followed instructions and yes it is a job to get at but it is a well filmed video. Thanks for attention to detail

[@iofix]

Great - glad it helped.

[@DannyCKJ]

Great vid man thankyou only one cud find aswell :)

[@nickoosthuizen2678]

Thanks for the vid helped me a lot

[@iofix]

Great, glad it helped you.

[@johncuthbertson2565]

Thanks to this video I had a go myself. It was successful though i did snap a connector off the holder attatching it to the bulkhead. I recon it was because I'm not giid with gentle and the plastic was cold (winter) The resister holder came out the housing with just my hand squeezing the tabs which was a bonus but payback because id snapped the motor plastic lug getting it bent out the way to twist. When twisted back on it all seems pretty secure so I'll leave it as is. All working well so 🙏 thank you.

[@iofix]

Glad it helped, thanks for the extra info.

[@johnelliott9415]

Yes those plastic clips are very difficult and tricky well done

[@iofix]

Thanks

[@propatria6382]

Great video; thanks!👍🏻 Do you know if it is the same with a left hand drive? Steering column cover instead of glovebox?

[@iofix]

Hi, I've never worked on a left hand drive one but I imagine it should be roughly mirror image configuration.

[@propatria6382]

@@iofix Thanks for your answer! I think i just have to take it apart. I fear it's the same as BSA might find too expensive to make a left and a right mounted v.motor. And if i'm right the job is a bit more complicated than the glovebox.😭 Christmas greetings from Denmark

[@hugonilsson6067]

Old comment but i suspect you found this out the hard way, like i just did, a real pain working under the steering wheel 🤦

[@mouftie618]

​@@hugonilsson6067Well, I guess I should have read trough the comments to know that in left hand drive, the motor still is on the left hand side

[@wendywhales2310]

Hi... Been watching another video where they are replacing bulbs in the panel at the top above the radio. With this top peoce removed. Would you have access to the Resistor for the blower motor.??.

[@iofix]

Hi, no I don't think so.

[@hugonilsson6067]

If anyone is trying this on a left hand drive car the motor is facing the same way which means you have to go in under the steering wheel, and yes it is a pain

[@20Fix]

but maybe you could get to the resistor through the glovebox side no?

[@paulroach3053]

I'm