2007 GMC Yukon Engine Replacement Part 2

[@EKHondaMotive]

Gotta hand it to you, knowing how much time setting up camera shots adds to the job, you stuck to it. Kudos! Makes you wonder if someone you know, perhaps in the shop (!), was the lone thumbs down... Good work bro!

[@1TexasDallas]

You're doing an awesome job with your videos great lighting not a lot of speaking or gibberish. I'm shocked that you don't have more likes and more subscribers than you do!!

[@АндрейЭлектрик]

Thanks for the piece of cardboard on 21:59. I thot one bolt is missing on my bell house. Bolt with nut- tranny dipstick bracket, two top left with brackets - breathers for transfer case, tranny harness and fuel lines.

[@quentinfrost2531]

Great content. I dread dealing with exhaust bolts.

[@baxrok2.]

Alrighty, making progress. Thanks!

[@throttlebottle5906]

so much for the days of "simple" engine swaps, unhook exhaust, fuel, half dozen wires, unbolt trans/converter engine mounts and go, maybe the hood. now, you start at left rear tail light work towards the front right across, diagonal to the left rear and repeat 12 times. there's far too large a divide between, design, engineering and mechanical departments. anyone whom works designing automotive should have minimum 3 years hands on in service departments, including the bean counters and management :)

[@EKHondaMotive]

throttle bottle While that may be true, about the complexity of modern powertrains, one has to take into consideration several differentiating factors between them. Reliability, fuel efficiency, specific power output are the the net results of design... ...old monochrome computers were easier to work on than the average touch screen enabled tablet... I guess my question is, would you rather old school simplicity or new school power?

[@tuxlinux1752]

Heat! on those exhaust manifold nuts...I use a venum hp anytime I have to do exhaust...just had an 08 brought in on a roll back and will get an engine next week

[@roadkill5333]

Heyyyy! You have a new schtick!! THE MIME MECHANIC!! :-)

[@roadkill5333]

Even when a wrench slips, you can't curse out loud!!

[@pinpointautomotiverepair1592]

lol it's just easier to work and not talk. I did my best to say more with my actions than with words.

[@JVerschueren]

I don't know how you do that. I work in a totally different field (electronics), but I talk to and cuss out the stuff I'm working on all the time. :D

[@DependableAutoTruck]

on exhaust i have a old 15mm cornwell impact mid lenght impact swivel socket and a 3ft breaker bar works good most of the time

[@tajcolvin785]

Bro u did aGreat job,, how many labor hrs involved in r&r

[@joshuamrshll22690]

If I wanted to change the bearings, do I have to remove the entire engine block or could I leave it in, expose the front like in this video and the change the bearings??

[@mikemichael9117]

I get the engine hot and then remove the exhaust flanges; have to do this first, before disconnecting everything else and still can be a pain

[@lpz3665]

Cant wait to play with my escalade.. has a slight rear main leak and a noisey lifter on start up.. time to remove complete engine for new stuff. Plus a supercharger. Im like a 52 year old kid.. already did my vette and the power is amazing. Im gunna supercharge my push lawnmower jus 4 fun

[@Sniperssx]

man thanks a lot please upload part 3 as soon as possible also if you have time can you epxlian by video how to change transmission oil level

[@DependableAutoTruck]

never removed crossmember have always gotten top bolts from the top after removing intake manifold might try your way on next one

[@comingundone27]

It must be nice working with music playing in some headphones. I am always taken off by phone calls.

[@ericcorse]

Those exhaust bolts didn't even look bad.

[@Limitlessmaint]

I don't understand why this subs come with that starter so hard to take off. It took me more than two hours to replace mine

[@luamayav]

Lol damn he went right to cutting before heating

[@deadone3503]

HE MUST GET PAID BY THE HOUR .CAUSE THERE IS A LOT OF SHORT CUTS HE COULD HAVE DONE

[@captainvanaroo1729]

Soon bestbuy will be the standard car truck dealer in USA there 90 percent made in China computers and parts in them and they should depreciate 50 percent after I second of puchase and 90 percent drop in value in one year like everything else at Best Buy sells.

[@testosteroneinc.3800]

FIRST😁

[@roadkill5333]

Aristotle Yiannis BEST!! :-D

[@pinpointautomotiverepair1592]

If I had t-shirts you'da got one 😂

[@captainvanaroo1729]

Hey wouldent it have been easyer to change the engine using a car crusher and go buy a 40 or 50 year old truck it’s a little cheaper