A less expemsive alternative to a true directional drill, probably best suited for residential/small commercial use in limied spaces.
@jackrichards18638 ай бұрын
I worked with a same assembly that pushed 20' drill rods in a 25' pit. Was worth $millions. 3" rods that would pull HDPE 200 mm diameter for 60 or 100 metres from pit to pit. Still a great deal of work but we could.never set foot on your land and pass a massive pipe under you without disturbing anyone much. Thrust angles were absolutely vital. And shoves rock right out of the way.
@superchuckie8 ай бұрын
What a lovely bit of kit 👌
@JustPlaneAround8 ай бұрын
If you are running across a field... there is no need to unscrew the pipes on the return trip. Just push the pipe through to the next pit and move your machine to the next pit... continue to the last pit and then unscrew the pipe. The cable follows the whole way. If you are going that far, I agree, just dig the trench and be done with it.
@williammorris3303 Жыл бұрын
Looks like it works great , except in areas like where I work where we would hit 63 boulders in that distance
@plissken94th579 ай бұрын
You’re absolutely right, I’m from Ventura county in California, anything in the conejo valley is easy to pull, hardly rocky and if it is, it’s usually gravel type rocky. If it is Rocky, we’ll usually reroute to main sewer and use a liner to repair the rest of the mainline, main reasoning being the one you stated, you get stuck in rocky areas, the machine pulls itself into the wall of the hole.
@RandomFandom19 ай бұрын
It could push a pipe under a sidewalk, amd that is about it.
@robertboykin18289 ай бұрын
well, there is something called C-4
@skitidet43028 ай бұрын
I live on the side of an esker, so 63 is an understatement. It's just rocks all the way down ranging from like 2 inch ones up to 200 inch ones. You are lucky if you can even burry half a spade before you hit a rock. Digging is a pain, even with an excavator.
@semperfi25078 ай бұрын
Or tree roots ?
@michaelp7618 ай бұрын
Nice. 👍👍 It’s a similar version to a pipe bursting machine which pulls a cable through an old existing pipe.
@chrisoakey98419 ай бұрын
You need slightly longer rams so you dont have to do the half steps, or slightly shorter sections wiuld work. It would also be wise to add a loop over the top, or holes on either side of the chassis so the unit can be easily lifted and lowered using the mini ex you power it with. Save the manual handling of a heavy piece of equipment.
@Drakoman078 ай бұрын
Lots of small details like you mentioned would be nice. Also, a way to clear between those pipe sections where he had to locate and clear it each time. It probably wasn’t necessary for him to clear it but it was obviously his preference so it’d be nice for the manufacturer to consider that use case
@youngprince7168 ай бұрын
Fawkit lift it right by the hose lol jk
@jzeerod7 ай бұрын
used an old model once, inside were a set of grips, you pulled the entire mechanism out and flipped it around, when you pushed it would grab and when you turned it around, it would grab on the reverse because basically you flipped the grabbers around. something like cantilever, the more you pull the harder it would grip. this looks like a nice set up but the manual moving it around would disturb your levels, with the inset grabber, your entire frame stayed in place as you just flipped the grabbers reversed, put the plug on the end and start pulling or attach the water line and pull it back to the outside.
@bradley58197 ай бұрын
This has changed my life
@kbrod7Ай бұрын
Impressive rectangular box hole BTW
@guyh.41218 ай бұрын
Did you get the idea when you were using a log splitter? Nice machine👍
@ralphriffle11268 ай бұрын
Southern cal. Gas co. Used a tool similar to this. The operator and the person next to him died instantly when they pierced into a 50 thousand volt underground electrical conduit
@6181green8 ай бұрын
That's why locates are required before digging and free of charge
@ralphriffle11268 ай бұрын
@@6181green not always accurate. Use at your own risk
@tellmesomething2go8 ай бұрын
very sorry to hear that!
@jobfrancisco47708 ай бұрын
Eu gostei é uma ferramenta muito bem bolada que adianta e facilita o trabalho parabéns
@dtoad488 ай бұрын
how do you pull the cable the rest of the way now?
@rudyyarbrough51228 ай бұрын
If I had that excavator I would have had it all done in half the time.
@tractor93918 ай бұрын
not if there were a side walk or driveway and that what this thing is about, sorry all cant read between the lines for this demo.
@michaelp7618 ай бұрын
And 10 times the mess! Reinstate etc
@betrickey9 ай бұрын
Pretty slick!!!
@robertmccully27928 ай бұрын
Very cool for getting under sidewalks if you do not have buried boulders everywhere like in my area.
@tractor93918 ай бұрын
yep
@jesstreloar77068 ай бұрын
The first length added should be painted, (red?). When it comes back you'll no the next one is the last one. I suppose counting them works, but humans are visual.
@vinimarshall73019 ай бұрын
6 years later , yip we don it covered a full 5 meters 😂😂😂
@cwmbc8 ай бұрын
How long ar those joint threads going to last. It only takes one person to not fully thread it. Then it pulls apart on the retract. And no way of retreiving the rods.
@robertboykin18289 ай бұрын
the thing for going under roads etc. they have been using them for about 40 years. gotta look for buired electrik etc.
@johnbower7 ай бұрын
why have all the revs on the digger
@gradyrm2378 ай бұрын
Could you do a longer bore next video without an edit where you unscrew 300 ft of pipe?
@everythingtv19107 ай бұрын
hello man can you tell me the name of this machine and how much price where i find it .i need it for some reasons . i enjoyed watching this video you teach me something good .thank you for bring this vidieo to watch . awaiting your reply .REGARDS
@assassinlexx19936 ай бұрын
Rocks, roots, change in the dirt. Will play havoc.
@stephaneleroy11958 ай бұрын
Why you put the Wood?
@tellmesomething2go8 ай бұрын
you need a half-pipe to bring the new pipe out some more.
@rohanpatekar9266 Жыл бұрын
The machine cannot drill through hard soil and also the machine has lack of support so the base frame rises from its place as soon as the load starts to increase also it require a big pit to carry out the operation can @roddie inc has any machine that could be used for house hold connection which has less space accumulation and has more strength ?
@luisdeleon7058 Жыл бұрын
I bough one a few months ago and I had the same issues with it. I’m still trying to re-sell it. This machine needs more upgrades for it to work well. I probably would recommend purchasing the basement buddy instead of the pipe ram.
@rasmo2439 ай бұрын
Grundomat mole is much quicker and hole doesn't need to be as big.
@roberttouhey21245 ай бұрын
Absolutely
@xpezeiro9 ай бұрын
a hole this deep dug in Brazil anywhere here would already be flooded with water
@user-ep7ou6nv8l2 жыл бұрын
На сколько метров она делает прокол?
@informer6 Жыл бұрын
Pipe Ram Trenchless Pipe installation system for 25mm to 100mm. Good for Landscapers, electricians, communications and plumbing. This uses 61cm long rods instead of cables, you can use a locator with a sonde to track every move in the ground.
@nikadib9 ай бұрын
@@informer6what about pipe 160mm? Could it use this ram too?
@joeyrutherford17908 ай бұрын
wait till the find a directional drill its cool tho
@bulldozercambodia25485 ай бұрын
GOOD
@danielrichardson36139 ай бұрын
Run a piece of rope through the middle of the rods, then anchor the rope at the other end - tow line for pulling pipe or cable??
@kc8pnd9 ай бұрын
The service line is attached to the end of the push rod/pipe and pulled back in reverse.
@JohnRaySalazar7 ай бұрын
So this is what Farva meant!? Ram Rod!!!! 😂
@james107398 ай бұрын
Probably could have edited out most of the rods in the middle and just told us how many it was
@rutulpatel97492 жыл бұрын
Can you deliver this machine in India?
@informer6 Жыл бұрын
soon it will be in India.....contact info@terragontechno.com
@kempaswe40228 ай бұрын
Build one yourself for smal money
@skitidet43028 ай бұрын
To bad a machine like this can't work where I live. You can't push that rod more than an inch or two before you hit bolder after bolder.
@ChemurakaM2 жыл бұрын
А если камень?😉
@b.malnit89838 ай бұрын
Yup. Boulders would be a problem.
@bunsdad45309 ай бұрын
If you shim rod up pipe will drop in ground?
@logancarter21348 ай бұрын
If you would dig deeper where you are standing you could make it a lot easier on your back by not having to bend over so far.
@mubasharshoukatsindhu89432 жыл бұрын
Where from we can buy this machine and what is the machine model
@tractor93912 жыл бұрын
Roddie Inc 888-406-3821
@informer6 Жыл бұрын
soon it will be in India.....contact info@terragontechno.com
@mikeiver9 ай бұрын
Sure seems allot of work compared to a thumper...
@kawasaki80518 ай бұрын
I've had a lot of bad luck with missiles lately and it's getting old
@mikeiver8 ай бұрын
Yah, down side of them are the rocks. They are sure not perfect. Then again neither is this method since rocks can deflect it too. @@kawasaki8051
@PeterLee-zn3jl8 ай бұрын
Rocks...roots...hard pan ....water.....clay....oh my Short distances in soft sandy seems ok Leveling kit/stand for rig..? Loops/lugs for lifting..? Sizes ...section lengths...core removal in both pits for sleeve...?
@keanea78883 жыл бұрын
Pneumatic missles >
@markalton4610 Жыл бұрын
Are awful. I’m going to replace mine with one of these
@abhijeeths6770 Жыл бұрын
Can you provide the existing contact and dealer/distributor number to purchase this product in India.
@titovillarreal119 Жыл бұрын
In India 😂 people there don't pay 😂
@audisoundproductions Жыл бұрын
In India they use a guy with small shovel to dig a small hole to pass a cable 😂
@nhilistickomrad42598 ай бұрын
Its cheaper to use manual labor in india mate. And itll be faster with less headache prolly cost you like 800 bucks (10 usd ) and 3 hrs with 2 doods Source: im an indian in bihar.
@kemalkoese91788 ай бұрын
per fakt 👍👍👍
@user-ed2or3xe7r Жыл бұрын
а если вода и грязь в яме ?
@pffeffi7 ай бұрын
works until you hit a big rock i guess
@GROP3005 ай бұрын
стоит экскаватор, а в ручную опускает
@georgiablinds33218 ай бұрын
wow, it’s amazing how many negative comments. We’re doomed!
@tractor93918 ай бұрын
what do you expect from negative people, its just a small tool for going under side walks and driveways when an air mole tool is to big and you don't what to rent or buy a 250 cfm air compressor . selling the shit out of them and that's what there really mad about.
@StimulatingPresence6 ай бұрын
Sorry, my junk drawer is full. Looks like another solution looking for a problem. There are several better, faster, cheaper ways of doing this.
@King_TuTT8 ай бұрын
really damn slow. but does the job well
@Ultra310x8 ай бұрын
Nice idea but way to much work and labor intense just use air compressor and a bullet alot faster 🤷♂️
@grassmanBoca8 ай бұрын
That n an easy job in the yard nothing in the way
@kempaswe40228 ай бұрын
No problem if it damage a gas line, then you will have a nice hole for a pond 😂
@jmsengnaw25438 ай бұрын
ပိုက်သိုး သရုပ်ပြ
@jmsengnaw25438 ай бұрын
ရှုခင်းများ
@dardaniakosova14 ай бұрын
A
@brabuslgsonymansorytesla8138 ай бұрын
TASHKENT UZBEKISTAN SVARCHIK
@kempaswe40228 ай бұрын
Would not work here. Boulders big as a old wv beatle
@terryharris33938 ай бұрын
Another solution looking for a problem to solve. Not all ‘inventions’ are innovative nor necessary.
@kawasaki80518 ай бұрын
Some like this are. When you trying to run a water service under a busy road that can't be dug up.
@Flowing238 ай бұрын
no mention of the 17 different electrical, sewer, water, comm wires/pipes he broke on the way, without the ability to know he broke them, Hummmmm!
@kawasaki80518 ай бұрын
So basically when you can't use any type of boring machine is what your saying
@The_Sword33 жыл бұрын
You could have dug a trench with the shovel in half the time and effort
@maxreed5012 жыл бұрын
Often used under driveways, where you don’t want a mess etc.
@griznatle9 ай бұрын
Tell me you don't understand the point without telling me
@The_Sword38 ай бұрын
@@griznatle The point between your ears ?
@griznatle8 ай бұрын
@@The_Sword3 yeah you seem to be missing that material, or at least its fairly smoothed out
@StimulatingPresence6 ай бұрын
@@maxreed501 There are cheaper, faster, easier ways to get a water service under a 20 foot driveway span.
@user-en3bu3yp1l8 ай бұрын
Полное говно ... А как он будет извлекать эти пробойники ? Землю рыть ? 😢😂
@mikel95678 ай бұрын
Crappy, inefficient system only good for very limited conditions. Why would I waste money on a product like that which requires that much equipment. A pneumatic mole would be far more efficient and cost effective for small jobs and an HDD better for larger jobs. You can even buy boring drills to mount on a skid steer. No way would you ever see a system like this on a real job. To many better options out there.
@RandomFandom19 ай бұрын
This is a nothing demonstration. You could confidently push a pipe under a sidewalk, and that is about it.
@griznatle9 ай бұрын
That's what this machine is for, short trenchless work. Congrats
@RandomFandom18 ай бұрын
@@griznatle a drill with extensions works better, and has way more uses.
@griznatle8 ай бұрын
@@RandomFandom1 the amount of torque you would need to do that with a drill is.... Alot. And every time an extension is added, torque is lost
@RandomFandom18 ай бұрын
@@griznatle I think you under estimate this drill. It's a black and decker hammer drill out of the 80's with the spline drive. I've drilled 8ft long holes with no issue. We routinely use it for drilling 1.25" × 12" holes for dowels on the job. This tool gets used daily for the last 30 years