Piston Rings Installation Easily l How To Install Piston Rings

Easily install the piston rings in a typical way to ensure the longest life of the engine.
This video includes an easy way to install piston rings for a four-stroke engine
If you are servicing an engine yourself, this video contains notes that interest you. Some notes on installing piston rings from the spaces between each ring and the direction of the rings
The video shows the correct way to install the piston inside the engine.
I will be happy to subscribe to my channel and wait for your comment
• Install piston rings /...
• Piston Rings Installat...
• Piston & Rings l How t...
• Restoration Old engine...
How To Restoration Brush Cutter : • Restoration Brush Cutt...
How To Power Sprayer Pump Repairing : • Restoration Power Spra...
How To Repair the Carburetor : • How to Repair the Carb...
How to repair pull starter : • How to repair pull sta...
Thank you
Ahmed Adel.
___________________________________________________________________________
Juice by tubebackr | / tubebackr
Music promoted by www.free-stock...
Attribution-NoDerivs 3.0 Unported (CC BY-ND 3.0)
creativecommon...

[@yasoyaso2208]

احسن وانجح طريقة 180 درجة حتى بشعار المرسيدس شائع

[@funv3188]

Lord of the rings 😂😂😂 Verry nice work and informative video. Keep it up 👍

[@saidufontykargbo7457]

Your video is educative, thanks.

[@RepairingShow]

Thank you for your comment ❤️

[@SkypowerwithKarl]

I always put the gap of the ring away from the exhaust valve if possible. I also use a ring spreader. It helps the possibility of a twisted, out of round ring or damaged grove. Use the ring tool.

[@williamjacksebastian]

That is only really important in two stroke engines because in four strokes the rings can (and do) move around freely and one will probably face the exhaust anyway. I agree for two stroke engines, it is vital to do so to avoid ruining the engine once the rings get a bit too hot.

[@Pork-Chopper]

@@williamjacksebastian I'm not sure if what your saying is correct. 4 stroke engines not withstanding. Piston rings in 4 strokes "do not" move around freely, unless it's a super worn engine. First of all, the Pistons, with rings are installed with a piston ring compressor. Why? Because the piston rings have to be squeezed to fit the bore, and they will "expand" exerting spring pressure on the walls of the cylinder to make a tight seal. This spring pressure, that can be several pounds, holds the piston rings in place, therefore, they Do Not move around "freely" as you say. And yes, piston ring position does matter, and it is logical that you start the upper compression piston ring pointing away from the exhaust port, because you don't want the hot flaming exhaust gases to enter the piston gap. It's heat will distort the piston rings, it will reduce lubrication of the cylinder walls and increase blowby. So, no, piston rings Do Not move around freely. They are not designed to move around freely, like my Nuts....

[@williamjacksebastian]

@@Pork-Chopper My expertise leans much more toward two stroke engines however I have rebuilt half a dozen four stroke engines, I was always told that the rings are able to move freely and have not required any special equipmement to install them.

[@williamjacksebastian]

I have always been able to slot the piston in slowly compressing the rings with a small piece of metal or wood one by one, and yes I am very aware they fit the bore otherwise there would be no compression. They are not held in place by pins like on two stroke engines, and I'm going to go ahead and read up on if they can move on their own or not!

[@williamjacksebastian]

@@Pork-Chopper I have consulted the internet and it would appear the rings do move even inside the cylinder albeit not very much.

[@igmotors577]

This is an exemplary work and the way of explanation is very easy, thank you

[@RepairingShow]

Thank you so much

[@emredoruk35]

Wouldn't it make more sense to place 180* separately? For 180* compression leak. when you do it will be 120*. let me know if i'm wrong.

[@TheDeadMan3848]

I agree with you, however there are people who say the rings rotate while running 🤷…

[@rezarahman5]

​@@TheDeadMan3848it is possible to happen on 4 strokes piston

[@TheDeadMan3848]

@@rezarahman5 Some say yes, l personally don’t know 🤷‍♂️

[@yasoyaso2208]

احسن وانجح طريقة 180 درجة حتى بشعار المرسيدس شائع

[@yasoyaso2208]

احسن وانجح طريقة 180 درجة حتى بشعار المرسيدس شائع

[@s.c.o.t.t.7743]

Now that makes a lot more sense, seperating the gaps position will increase the compression. I know 1 side of the ring is sharper than the other, make sure the sharp end is the bottom to prevent the oil from leaking through to the combustion area.

[@jainuriplm1532]

Semoga bermanfaat buat cenelnya salam otomotif dari Palembang 👍👍🇮🇩.

[@RepairingShow]

Thank you very much

[@scorps9398]

Great video. I've been looking for one like this straightforward!!

[@adeelautosworkshop373]

Nice work 👏

[@RepairingShow]

Thank you

[@henkmeiring01]

Ring gap position is actually pointless.Because rings turns in grooves randomly due to vibration,you cant control it.Only two strokes keep rings stationary,due to pins on piston.You can allign all ring gaps at installation,if ring gaps are what they should be,compression will be 100 percent and oil consumption nothing to speak of. Far more important is lack of info and clarity by some manufacturers what should be top and second ring and clear markings which side up

[@bluegizmo1983]

Old post, I know, but this is absolutely NOT true. A lot of four stroke pistons even have small notches inside the ring lands to help you align the rings to a specific spot, and those notches will absolutely not allow a ring to spin. Rings should NEVER be spinning inside the bore. If they do, you have a problem.

[@tansugunal]

​@@bluegizmo1983Some of them are really confusing. For my 110cc kit they are 99% arr the same. And their machining angles are against the industry traditions that you can find on internet. I don't know why they have a secret code to install some super primitive pieces... What I only believe is 2.nd ring is a little bit thicker and harder.

[@ulyfix3261]

Very wrong piston ring position.. never ever put ring end gap on piston pin hole..

[@archiedentone5950]

If you ever played attention when you take the piston out of a run engine it is just as likely to be there as anywhere else

[@chegechegeh4545]

What happens if u do plz help us

[@archiedentone5950]

Bullshit

[@archiedentone5950]

@@chegechegeh4545 nothing

[@spencertawandakufakunesu7170]

Neither should you put ring gaps on thrust side of piston

[@chamathransara4342]

Nice bro 💘

[@RepairingShow]

Thank you for watching

[@twinturbo3900]

Bro APAche bike piston aeromark is lnlet side or exhaust side tell me plz

[@hebagallop1061]

So good 💪💪💪💪

[@RepairingShow]

Thank you for watching

[@narasingaraodadi3558]

Excellent

[@RepairingShow]

Thank you for watching,❤️

[@jimmaag4274]

This must be the "new and improved" way. Thanks but I'll stick with the old (correct) way.

[@jaeda88]

How much does it take to replace pistons on a 2005 A3 petrol 1.6L? Just curious... Tia

[@ilcnnd]

Why did you install shiny ring as the second and black as the first?

[@RepairingShow]

I have received a lot of comments and this is the first comment that mentions this error, I apologize for this error

[@MrAedes_96]

Good👍👍👍👍

[@gmc-roots-blown273]

Hastings says not to spiral the compression rings on but then you have to expand them a bunch. Not sure which is worse

[@mitreswell]

Most important aspect is to set the ring gap properly.

[@RepairingShow]

Right

[@mohsinshahzad475]

Meny rings change karwai hein , zyada race deny sy bike missing karta hei is ki kya waja hei

[@alaakhalifa2419]

Thanks for your great effort ❤️

[@RepairingShow]

I really appreciate your comments

[@tiepnguyen646]

@@RepairingShow được nhiều sự quan sát của phóng

[@newera3135]

Really amazing and brilliant

[@RepairingShow]

Thank you for watching and your kind comment

[@calebengelbrecht7812]

Hi, i am busy working on my compressor, but after re-assembly the piston feels rough. Any advice?

[@RepairingShow]

Check that the piston rings move easily inside the cylinder and that the connecting rod is installed correctly or not

[@hebagallop1061]

ولله انت بطل

[@intech2688]

Good

[@RepairingShow]

Thank you

[@eddiesolidarios8207]

very good demonstrationm

[@CamperTG]

where is piston cup located?I didnot find any video related to this!

[@RepairingShow]

What is the piston cup 🤔

[@nv1493]

You never twist the top rings into position. Use the right tool.

[@RepairingShow]

you are right. I will do that thank you

[@fabrivila2774]

Excelent vídeo, thank you so much.

[@RepairingShow]

Thank you for watching ❤️

[@jesusjesus9722]

Super

[@gboysumampong4004]

Wrong. Firts ring nilagay sa second ring. Ung oil ring nsa butas at sa pin. Susuka ng langis pag ganyan install mo

[@joadirkuster6261]

Top!

[@orvillecoronado3080]

Use piston ring expander

[@RepairingShow]

Thanks you for the clarification. I'll do it

[@manilynmartinez1196]

Sir anu sira ung ng hahalu ng langis at tubig Ty,

[@RepairingShow]

Sorry, hindi ko maintindihan ang ibig mong sabihin

[@Pianissimo1970]

Split the ring with your thumbs and place it carefully into the groove, You're putting too much stress on those rings, they'll probably break later

[@RepairingShow]

you are right. I was very careful while installing the loops. Thank you very much

[@somu_v9668]

Yep.. I follow this way while removing and installing.. It's good approach

[@kd5ozy]

This exactly how not to do it!!! use ring pliers!!!!

[@RepairingShow]

I promise you

[@hafeezabubakar9697]

Hi engine

[@lucientjinasjoe1578]

This is a 4stroke piston and have no exhaust port and flush port

[@cengizeroglu5020]

Bu olay her araçta geçerlimi tenkhu

[@RepairingShow]

This applies to any small engine

[@ahmetdemir6830]

Piston rings cannot be installed by hand, you are using the wrong method.

[@justicemoyo651]

That way can break those rings easily

[@kennethmartin-sm1mr]

How to tell which is whitch

[@RepairingShow]

Thanks for watching, but I didn't understand the meaning of the question

[@shehan8603]

❤️❤️❤️

[@RepairingShow]

Thank you

[@archiedentone5950]

It doesn’t matter how you stagger the rings as they rotate as soon as the engine fires

[@hashimamin340]

i think its a heavy bike engine ?

[@RepairingShow]

This is a multi-functional engine but not much different from a bicycle engine

[@hebagallop1061]

❤❤❤❤❤❤

[@ChiefCabioch]

Oiling the ring lands is asking for trouble, that oil will turn to carbon when the engine fires and runs for a while, you only lube the skirts below the rings, and the cylinder walls, that's more oil the the top2 rings will ever see, and the engine won't puff blue smoke when you fire it,

[@marshalllhiepler]

True, but you generally can't reason with a mechanic. He will keep oiling ring grooves, fouling new plugs, and gumming up the compression rings. Oh well.

[@ChiefCabioch]

@@marshalllhiepler then that makes him an idiot, and loses his "mechanic" moniker

[@ChiefCabioch]

Spacing ring gaps less than 180° apart give combustion gases an easier path, space them ALL 180° apart, starting from the top ring down top gap at top of cylinder and second bottom of cylinder, oil expanders 180° also

[@ВладимирВикторов-ю1м]

Никогда так не делайте!

[@stephenmacdonald912]

As long as the gaps are staggered it doesnt matter exactly which way the go. Itll still work

[@RepairingShow]

Actually any way, but what is important is the spacing of the rings

[@Phiyedough]

I am pretty sure this method would result in broken rings if the oil rings were the cast iron one piece type.

[@RepairingShow]

Welcome. Thanks for the comment, but it works after installing the rings a year and a half ago

[@jabber18jabber18-ru1hf]

Hello

[@KarimKarim_91]

WRong position

[@samuelesios5609]

Ayaw ka mag kanit ng piston rong ng gat sa or mlalapit sa piston pin

[@Funistudo]

USE

[@customizer6509]

Кольца нумеруются наоборот бестолочь. И где ты видел чтобы кола сразу одевали на своё место диот

[@DaveMcLain]

Absolutely the wrong way to install the rings. NEVER spiral the rings into place use a ring expander. Otherwise they are now junk.

[@ahmetdemir6830]

You are showing people wrong that piston rings cannot be installed by hand. Circlips bend when installed by hand.

[@joeblowjohnny2297]

Wtf ? He didn't show rotation if rings gap placement location before dropping piston in ? Wtf ?

[@kimienick6721]

Left and right and doesn't matter akso can right and left but dont put into EXHAUST OR INTAKE place... the answer is BURN BABY BURNT 🥵🥵🥵

[@RepairingShow]

Thank you for watching

[@redenora7840]

Its wrong piston ring pisition,you don't have to installed the piston ring gap along the piston pin,😁

[@daweil]

I never understand why you would even stagger the rings because they rotate when the engine operates. I have removed many pistons. All the gaps tend to go to one spot.

[@RepairingShow]

The piston and rings do not move in a circular motion inside the engine until they move

[@thembelihleduma5903]

Great explanation you are ryt the rings doesn't rotate coz if they rotate the smoke can occur

[@ChaucerMolly]

Lee Joseph Jackson Thomas Perez Patricia

[@alvinlabao6044]

Its very wrong position bro dont do this because cunssuming oil after also breater smoke to much

[@philouphil]

twist the segments 😲 Sorry this is not a decent job

[@malikrameez703]

Wrong innastlation

[@danielsalvatierra854]

Mal manipulados para la colocacion

[@marshalllhiepler]

Simple logic dictates that the two compression rings should have their gaps positioned 180 degrees apart. The gap for the oil control ring is not sensitive to position, but logic again suggests that it not be placed on the "thrust" side of the piston, thus allowing a less sressful break-in for it. You can either install rings in the fashion that is recommended for stupid mechanics, or you can use your brain.

[@JustinPaul1st]

You dont have to be insensitive...each to there own baba...🐵🐵🐵

[@marshalllhiepler]

@@JustinPaul1st, Indeed. Let your limitations guide you.

[@nickleinonen]

For all the engines I’ve worked on, I never put compression ring gaps on the major or minor thrust locations. So nothing inline with the wrist pin, nothing perpendicular to the wrist pin. 45° to one of those is fine, and 180° between the 2 compression rings. All my work has been on large diesels (1200-4500hp) but same theory applies to all IC engines. The oil ring I usually clock the gap at 90° from the bottom compression ring.

[@bernardjara6461]

Wrong

[@RepairingShow]

Why?

[@Funistudo]

daM

[@nishadebrahim8922]

Don't fix the rings in that pin side

[@RepairingShow]

Thank you for the correction

[@duartejoao3430]

Bad info. Use the ring tool

[@RepairingShow]

I will. I promise you

[@jp-me9zz]

WTF… This is wrong in so many ways..

[@RepairingShow]

Why?

[@neildougherty3377]

Totally wrong

[@RepairingShow]

Why?

[@VernonBryansnyders]

I need a better video to install. Pistens

[@RepairingShow]

Thanks for the comment. I will make a video later

[@marijamagdalena1356]

Total nonsense, pistons rings like my grandmother skills.

[@andrerousseau5730]

What complete and utter rubbish! This video perpetuates the tired, old erroneous myth that circumferentially separating the ring gaps somehow 'helps' engine compression - IT DOESN'T!! Not a shred of difference because the rings rotate in their grooves (unless pegged, eg 2-strokes) (around ~ 150-200rpm) while the engine is running. You fools!!

[@RepairingShow]

Your comment made me research the matter extensively and scientifically. Your comment is really good for me. Thank you

[@ChotuuSian]

Good work 👍

[@RepairingShow]

Thank you for watching 💚

[@Tluangaa-h5b]

Good

[@RepairingShow]

Thank you for watching

[@henkmeiring01]

Ring gap position is actually pointless.Because rings turns in grooves randomly due to vibration,you cant control it.Only two strokes keep rings stationary,due to pins on piston.You can allign all ring gaps at installation,if ring gaps are what they should be,compression will be 100 percent and oil consumption nothing to speak of. Far more important is lack of info and clarity by some manufacturers what should be top and second ring and clear markings which side up

[@veraoluchi9723]

Hi

[@RepairingShow]

Hi Welcome to my channel

[@mumuniharuna1282]

Good

[@RepairingShow]

Thank you for watching