Haha! What are the odds, I go on KZbin, grab the first video on spray gun problems, and the first thing you illustrate is my exact issue! Thanks for the vid I needed!
@JKheller197 ай бұрын
Haha! Me too! I took it off and cleaned it but still seem too have this issue. But it's way better though
@kevwills85810 күн бұрын
Me too "Fluttering" But it took 5 previous videos that didnt address any problems or fixes.
@nippychippy5 жыл бұрын
Best video I have found on gun issues. Thanks for taking the time to make it
@mikethomas64084 жыл бұрын
You bloody beauty. She was pulsing, you solved my problem. Good onya Mate
@kiwi35117 ай бұрын
Thank you so much for your video, it fixed my issue straight away! no more fluttering. I only had it hand tight after first using my gun and the clean up, thanks mate.
@ocendo113 күн бұрын
Thank you for your good work in comunity.Long live and prosper
@willyisaac39553 жыл бұрын
Great video my dude!! Just awesome thank you so much, even went in detail about fixes. Your the man!
@sonnycoasta2 жыл бұрын
October 2022 and this video is still helpful. Thank you 👍🏽
@gerryfaught835311 ай бұрын
Man this was helpful I was about to junk this clear gun.....Thank You
@MrMechanicandy Жыл бұрын
The hvlp gun I have that looks like this one wasn’t picking up enough paint but the vent tube was plugged and I realized something was wrong cause you unhook air hose and gun still has pressure enough to squirt out paint . Vent pipe at the 90 elbows was plugged I cleaned them will try again tomorrow
@williamwixon2 жыл бұрын
Thank you so much!!! My gun was pulsing. I haven’t tried yet but I am praying that this will resolve the issue!! Goddamn urethane paint so expensive! I was praying there was an online video so that I didn’t have to spend hours and hours trying to figure it out on my own!
@4myeyes9252 жыл бұрын
Do you have a fix for air coming out of the gun with out squeezing the trigger? And once the trigger is squeezed it stops the air flow??
@marinvremes57026 ай бұрын
Thank you for sharing valuable information. I have a SATA 5500, used to make spray outs only at the moment ( not a painter yet, still in training). Since yesterday, it started something strange : with the trigger half way on, jut to blow air to dry the card, the air is going in to the paint cup ( 3M single use ), literally inflating the cup like a balloon. What can it be the cause of this issue?
@svenphelps29211 ай бұрын
Why is mine building up paint at the tip of the gun? Is it too much air? Is the fan too wide? I can’t ever get a good spray with these guns. Are you not supposed to use oil based paint with these? Everything I paint looks bad bc I can’t get a good spray. This video was helpful in other cases, but not with what I need. If my question could be answered that would be great
@johnnytocino93132 жыл бұрын
Great info. Thank you a thousand times over.
@leeedwards73582 жыл бұрын
He touched on some series points (awesome)!!!!! Keep up the the good work
@killablooz5 жыл бұрын
Thanks for this. Sorted out my pulsing spray problem.
@masterofpc114 ай бұрын
I've had a really really annoying weird problem, where the paint would come out in big blobs instead of a nice mist like expected. I've tried everything - air pressure lower/higher, fan adjustment tighter/bigger, adding thinner etc. but nothing would solve it. In the end, the small holes in the air cap on either side of the nozzle were plugged with old paint. After soaking in thinner and blowing out with 6 bars of compressed air, it works like a charm again. This wasn't mentioned in any of the troubleshooting videos, probably because it's so easy? So I'm leaving this here for others who might have the same problem... TL;DR when the gun doesn't work like it's supposed to, first thing is to really really clean it well including all the small holes.
@sambodutch54337 ай бұрын
This helped me a lot today. Thanks.
@Dragonclaw1032 жыл бұрын
My gun requires not to exceed 50 psi. I have my compressor set anywhere from 30 - 50 and I get nowhere the same air pressure that you are getting out of your gun. Could possibly my gauge be off?
@blaiketillman3691 Жыл бұрын
Did you buy a new gauge or borrow one to see if yours might be inaccurate?
@Dragonclaw103 Жыл бұрын
@@blaiketillman3691 I went back and looked up my model instructions. Where it said not to exceed 50psi.. it was referring to working pressure, as in the pressure reading as the gun is spraying, and not sitting pressure, or not spraying.. I made that adjustment and it is spraying well now.
@aprilmarcha95873 жыл бұрын
Thank you ! Got me up and going again !
@LiloUkulele4 жыл бұрын
Problems solved! 2 thumbs up 👍
@kenneth673110 ай бұрын
How does a gun like this stack up to modern guns like the HF black widow?
@JesemanuelRamirez5 жыл бұрын
What if the nozzle is tight and it still stutter?
@jamesthompson62692 жыл бұрын
Same issue here i can't find no leaks yet still pulsing
@슈퍼리치베어3 жыл бұрын
im korea painter . The tip to control paint amount is broken. this is my devilbiss luna. i think the screw line is worn out a little. please tells me how to repair this problem?
@derekdickinson1 Жыл бұрын
great content listened to content but couldn't watch the video as the blurred picture drove me mad.
@gregsantos9731 Жыл бұрын
Thank youvery much, this is very helpful 😊
@theematrixhasyou13 жыл бұрын
What about when you have dead spots/no paint within a wide fan pattern ?
@SamFBM2 жыл бұрын
mine has a problem , i hook it up to air and theres air hissing out the tip without touching the trigger.
@Martink91913 жыл бұрын
My gun sprais droplets instead of fog... what causes that? I noticed airbubles in container also.
@abtra5 жыл бұрын
I have a lvlp gun that has a stream of paint when I take my finger off the trigger. If I tighten the screw at the nozzle all the way right it doesn’t drip but I get a very small spray pattern.
@PittsburghSprayEquipmentCo5 жыл бұрын
Most likely your fluid needle return spring is worn or your nozzle, needle are worn (more likely that the fluid needle return spring is worn though) Thanks
@jamesfraser13403 жыл бұрын
Stick a couple of small washers onto the back of the spring
@Psychomantis619 Жыл бұрын
Honestly thank you.
@shreejithaindrajith44933 жыл бұрын
Great tips brother , helped me out
@mrprecious12346 жыл бұрын
Thanks for the tips.
@1mcl4768 ай бұрын
Thank you so much help a lot 🎉
@VladanLukovic0114 жыл бұрын
Great video, thank you. Still I have strange problem not covered here: My Sagola paint gun worked well until one day just started to blow air into paint dish instead suckin it. Can anyone advise please? (Detail cleaning with dissasembling and assembling was already done). I can't figure out what is wrong.
@abrahamjimenez13793 жыл бұрын
i have the same problem and looking for a solution, did you found out what was it?
@VladanLukovic0113 жыл бұрын
@@abrahamjimenez1379 Not really. I'm pretty sure that it is sealing issue, but I didn't found spare parts for this old model here in Serbia. Try to replace sealings if you can find them to buy. At the end i bought Italco HD2 advance and it works like charm.
@keyikush3 жыл бұрын
I had the same problem too. I Opened all screw. And wrap all thread with white seal tape and put everythings back. make sure all screw are tightened
@d477a52 ай бұрын
Thank you!
@MimiFlores-p6cАй бұрын
Anybody kmoes why My sprayer males a buzzing sound
@SunShine-nh7yo9 ай бұрын
Excellent, thanks
@rustynuckles36625 жыл бұрын
I was just spraying paint with a Sanborne siphon gun and went to clean it out for clear coat, now I have no flow. What causes that?
@jermainemiglietti12443 жыл бұрын
So helpful thanks mate!
@deepahareesh90303 жыл бұрын
How I solve Leak from back side of nozzle?
@michaelcribb72054 жыл бұрын
What about from the paint tube in the bottom that feeds the paint is not spraying all the way barely getting paint out of it and it's a bottom feed paint gun not an expensive one
@PittsburghSprayEquipmentCo4 жыл бұрын
If its a siphon feed and not siphoning then it's a air cap issue maybe its not tight enough maybe its not a good enough air cap for the paint to siphon these would be the most common reason
What should I do when there is no material flowing? I only get air instead.
@PittsburghSprayEquipmentCo3 жыл бұрын
Hi you may need to remove the needle and clean it. You can also check if the needle is being pulled when you pull the trigger , it should be, finally you may have to small of a tip for your paint
@vmaniac47893 жыл бұрын
@@PittsburghSprayEquipmentCo alright i give it a try, thanks
@Michigunner4 жыл бұрын
Sata minijet. No air at the cap. Does not atomize fluid. Has me stumped. Cleaned it can't figure out
@PittsburghSprayEquipmentCo4 жыл бұрын
Don't know sata to well maybe a baffle missing behind the fluid nozzle or your air valve is not in tight
@andrewsnider78896 жыл бұрын
What is the problem when the gun does not pickup any paint or thinner in cup??
@PittsburghSprayEquipmentCo6 жыл бұрын
Hi Andrew with a siphon feed (cup on bottom) this is usually due to your fluid nozzle not being tight enough, or it could be an air cap that doesn't siphon (pressure feed caps will not siphon)
@deanflatt20352 жыл бұрын
My spray gun is blowing air but no paint coming out
@CleanCutt Жыл бұрын
thank you ...
@2-4outdooradventure533 жыл бұрын
Thank you! I was about to throw this sprayer in the trash!
@angelolivarez86923 жыл бұрын
Lol me too
@ericescalante55212 жыл бұрын
Same here .lol
@xiangruiairmachineryequipm37752 жыл бұрын
Very good
@jeremyspecce5 жыл бұрын
I'll give you a pass on the audio quality because you got my gun working again in like 5 minutes.
@jamesfraser13403 жыл бұрын
Bet he sleeps better now
@realestateinfonet90413 жыл бұрын
Great video! Thanks!
@kevwills85810 күн бұрын
Thanks 👍🇦🇺
@heidel4203 жыл бұрын
"So if you have a plug in the cap, that''ll do that ... so we fixed that ..." Umm, I was hoping you'd show how you fixed it.
@PittsburghSprayEquipmentCo3 жыл бұрын
Plug in an air cap use a small pick and dislodge it if that doesn't fix it may need a new air cap
@juankduyvestein16294 жыл бұрын
Y en español cuando o dónde lo puedo ver
@johnbergeron34865 жыл бұрын
Very informative
@mondomg6 жыл бұрын
Quick Morty, get the spray gun!
@RareParts3769 Жыл бұрын
Nice
@brianburgess5909 Жыл бұрын
Get closer to the mic. Cannot hear.
@LiloUkulele5 жыл бұрын
my tip keep clogging?????
@codywebb93024 жыл бұрын
Are you useing high quality paint and thining out your paint
@ahmadnazir9943 Жыл бұрын
Hello
@rong41893 жыл бұрын
The reason your gun is spraying to the right is because there’s a piece of duct tape stuck to it. You’re welcome. Seriously though, this is a helpful video, thanks!
@randomaccount4873 Жыл бұрын
Not spreying not...spill
@mariodellatorre12996 жыл бұрын
Dalle foto sembra eccezionale ma ci vorrebbe una prova pratica
@randomaccount4873 Жыл бұрын
Air flow 10%....no section 0%
@mastmec4 жыл бұрын
Stop talking while spraying, can’t hear you.
@tucayojct4164 жыл бұрын
Get hearing aids.
@TheShittyCyclists Жыл бұрын
Bang on mate cheers 🖐this spray gun has has been driving me fuckin nuts👌😎👍